TJA1041T/N1 - 1Mbit/s CAN Transceiver | NXP | SOIC-14
MPN: TJA1041T/N1 ✗ 停產TJA1041T/N1 概覽
A CAN transceiver is an interface IC within the automotive network-communication hierarchy. It translates the controller's logic-level TXD and RXD signals into a differential bus waveform for transmission and converts received differential bus levels into a logic signal for the controller. This physical-layer function complements the CAN protocol controller, which handles message identifiers, arbitration, error handling, and higher-level data exchange.
The TJA1041T/N1 provides differential transmit capability, differential receive capability, and compatibility with high-speed CAN protocol controllers operating up to 1 Mbit/s. Its single-transceiver arrangement suits conventional CAN nodes that do not require the additional transceiver features found in sleep-capable variants. The SOIC-14 package supports surface-mount assembly while providing separate pins for the bus interface, logic interface, ground connection, and stabilization.
Automotive and industrial CAN networks benefit from the robust differential signaling inherent in the TJA1041 architecture. Differential reception rejects common-mode voltage present on the bus, while the controller and transceiver can use twisted-pair wiring to maintain signal integrity over longer cable runs. The manufacturer's product documentation identifies the device primarily for automotive high-speed CAN applications and confirms compatibility with suitable CAN protocol controllers.
Typical deployments include engine-control units, transmission controllers, body-control modules, gateways, electronic control units, industrial automation controllers, and CAN-based sensor or actuator networks. In these systems, the TJA1041T/N1 handles the physical bus layer while a separate CAN controller manages frame arbitration, acknowledgments, error counters, and communication with the host processor.
Designers should follow the manufacturer's recommended transceiver and bus-line application circuit, including termination, common-mode choke or split-termination options where required, decoupling, and PCB routing guidance. The 1 Mbit/s capability does not remove the need for controlled bus topology, adequate ground references, correct termination placement, and protection suited to the vehicle or industrial environment.
This page combines the TJA1041T/N1 lifecycle information, verified source links, same-footprint alternatives, application guidance, and engineering design notes to support component selection, PCB planning, and long-term supply-risk assessment.
直接替換替代品,適用於 TJA1041T/N1 — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: TJA1041T/N1 (相同外形與佔位) — 差異在於 Bus Interface, Package, Product Type.
TJA1041T/CM,118
✅ 直接替換📋 參考替代品(不在目錄中)
TJA1050T/N1
✅ 直接替換聯絡詢價
查看資料表 →TJA1041T/N1 規格
| Product Type | High-speed CAN transceiver |
| Supported Data Rate | Up to 1 Mbit/s |
| Transceiver Configuration | 1/1 half transceiver |
| Bus Interface | Differential CAN transmit and differential receive |
| Protocol Compatibility | Compatible with suitable high-speed CAN protocol controllers |
| Primary Application | Automotive high-speed CAN nodes |
| 封裝 | 14-SO |
| 安裝方式 | SMD/SMT |
| Manufacturer | NXP Semiconductors |
| 生命週期狀態 | End of Life |
| Supply Chain Status | Shipping discontinuance and replacement information available from NXP |
| Number of Transceivers | 1 |
| Interface Category | CAN interface IC |
TJA1041T/N1 14-so 腳位配置指南
TJA1041T/N1(14-so 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。
無詳細腳位定義資料: TJA1041T/N1.
請參閱 資料表 以查看完整腳位配置。
典型應用
TJA1041T/N1 適用於 6 應用s: Automotive Electronic Control Units, Body-Control Module Networks, Powertrain and Transmission Controllers, Industrial Automation CAN Gateways, CAN-Based Sensor and Actuator Networks, Vehicle Network Gateways.
Automotive Electronic Control Units
The TJA1041T/N1 fits an automotive electronic control unit that requires a high-speed CAN physical layer, because NXP identifies the device for automotive CAN nodes operating up to 1 Mbit/s. The IC sits between the CAN protocol controller and the differential bus, translating TXD into the bus waveform while converting received bus levels into RXD for the controller. Its 14-SO surface-mount package supports compact, automated PCB assembly. The design must follow the manufacturer's bus-line application circuit and account for automotive ESD exposure, ground reference, bus topology, and termination placement.
推薦
Body-Control Module Networks
The TJA1041T/N1 is appropriate for a body-control module that exchanges switch, lighting, door, and sensor data over a 1 Mbit/s CAN network. Its differential transmit and receive interface reduces susceptibility to common-mode noise found in vehicle wiring, while the separate CAN controller remains responsible for arbitration and error management. The SOIC-14 package allows placement on a conventional multilayer automotive PCB. Layout should minimize loop area around bus and ground paths, keep transceiver supply decoupling close to the device, and place the network termination at the physical bus endpoints.
推薦
Powertrain and Transmission Controllers
A transmission or powertrain controller can use the TJA1041T/N1 as the 1 Mbit/s physical interface between its CAN controller and vehicle network. Differential signaling supports reliable communication over twisted-pair harnesses, while the transceiver's dedicated transmit and receive functions separate bus drive from logic-level reception. Because this is an End-of-Life device, an automotive program should evaluate lifecycle continuity, approved-source availability, date-code control, and change notification before committing the part to a new platform. The PCB and bus implementation should follow the manufacturer's reference topology.
推薦
Industrial Automation CAN Gateways
The TJA1041T/N1 can provide the physical layer for an industrial CAN gateway that links sensors, drives, remote I/O, or factory controllers at up to 1 Mbit/s. Differential CAN communication is useful in environments where cable routing passes near motors, switching equipment, or other noise sources. The gateway still requires a separate CAN protocol controller, and the bus must be designed for its maximum length, node count, topology, and termination. Engineers should verify temperature and environmental requirements for the installed enclosure and consider the device's End-of-Life status when planning product longevity.
推薦
CAN-Based Sensor and Actuator Networks
The TJA1041T/N1 is suitable for a distributed node that connects a sensor or actuator to a 1 Mbit/s CAN backbone. The controller can originate periodic measurement frames, while the TJA1041 provides the differential physical signaling required across the wiring harness. In a multi-node installation, correct termination and topology are as important as transceiver speed because reflections and excessive cable length can impair bit timing. The 14-SO footprint simplifies conventional surface-mount assembly, although the circuit should include the supply and bus-network components specified in the manufacturer's application guidance.
推薦
Vehicle Network Gateways
The TJA1041T/N1 can form the high-speed CAN side of a gateway connecting separate vehicle network segments. One CAN controller manages protocol activity on the selected bus, while the TJA1041 handles differential transmission and reception at up to 1 Mbit/s. This separation keeps physical-layer behavior separate from message filtering, diagnostic handling, and gateway software. For a new production design, lifecycle risk should be resolved through NXP's discontinuance information and a structured request for current supply. PCB routing must preserve the intended bus-impedance path and provide a low-impedance ground reference.
推薦
推薦產品摘要
工程參考資料,適用於 TJA1041T/N1 — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | TJA1041T/CM,118 | TJA1050T/N1 |
|---|---|---|---|
| Package | SOIC-14 (14-SO) | SOIC-14 (14-SO) | SOIC |
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Product Type | High-speed CAN transceiver | High-speed CAN transceiver | High-speed CAN interface |
| Supported Data Rate | Up to 1 Mbit/s | 1 Mbit/s | 1 Mbit/s |
| Primary Application | Automotive high-speed CAN | High-speed CAN interface | High-speed CAN interface |
| Mounting Style | SMD/SMT | SMD/SMT | SMD/SMT |
主要差異化特點
- Established 1 Mbit/s automotive high-speed CAN positioning (對比TJA1050T/N1)
- Standard N1 ordering configuration (對比TJA1041T/CM,118)
- Single 14-SO high-speed CAN transceiver (對比TJA1041T/CM,118)
設計說明
Route CANH and CANL as a closely coupled differential pair, referencing the PCB ground plane. Avoid long stubs, test pads that break coupling, and unnecessary vias. Keep the transceiver, its CAN controller, and the bus-line conditioning components close together so that transmit and receive paths remain compact. The manufacturer's application circuit should be used to determine trace geometry and the location of any common-mode choke.
Do not assume that a 14-pin CAN transceiver can be replaced solely because the package matches. Verify TXD, RXD, ground, supply, stabilization, mode-control, and no-connect assignments against the manufacturer pin table. In particular, TJA1041T/CM,118 adds standby and sleep-mode characteristics, and TJA1050T/N1 may differ in logic-pin implementation. Confirm propagation delay and mode behavior before approving a substitution.
Place the transceiver's required supply-decoupling components close to their associated pins and follow the manufacturer network recommendation. Keep switching regulators, inductors, and high-current return paths away from the CAN receive path to reduce differential and common-mode noise. If the bus requires a split termination or common-mode choke, select its values and placement according to the manufacturer's application guidance rather than general-purpose rules.
Evaluate transceiver power dissipation from the actual supply voltage, dominant current, and bus activity rather than from a nominal output-current rating alone. The 14-SO package should be placed on a PCB with an appropriate copper area and solid ground reference. Confirm the manufacturer's operating-temperature limits and maximum electrical ratings for the selected grade, particularly for automotive applications exposed to temperature extremes.
End-of-Life status should be treated as a supply-planning constraint. Record the exact ordering suffix, quantity, date-code preference, inspection level, and traceability requirements when requesting supply. Do not substitute another TJA1041 packing suffix or family member without engineering approval, because the ordering code can represent a distinct mode configuration even when the package and headline CAN data rate are identical.
合規資訊
The NXP product page provides environmental quality and lifecycle information, but the verified product records do not explicitly state the required compliance statuses. No compliance claim should be inferred from the automotive application description.