VSC8541XMV-04 Single-Port Gigabit Cu PHY | Microchip
MPN: VSC8541XMV-04 ✓ NakahandaVSC8541XMV-04 Ulas
A copper PHY, or physical-layer transceiver, is the circuit that converts logical Ethernet data into signals suitable for transmission over twisted-pair cabling. Within the network hierarchy, the VSC8541XMV-04 is an Ethernet interface IC that connects a digital network processor, switch, router, or other host controller to a 10/100/1000BASE-T copper network. Its multiple interface options allow it to address systems with different clocking, data-width, and board-layout requirements.
The device combines Gigabit-class network connectivity with low-power operation and a compact 68-QFN package. Energy Efficient Ethernet can reduce link power when the traffic load permits it, while Wake-on-LAN supports remotely waking compatible networked equipment. Synchronous Ethernet provides a mechanism for transferring timing information over Ethernet links, making the PHY relevant to infrastructure equipment that requires synchronization.
The available GMII, RGMII, MII, and RMII interfaces are important selection criteria because they determine how the PHY connects to the host controller. GMII and RGMII support parallel Ethernet signaling, while MII and RMII are commonly associated with lower-speed or lower-pin-count implementations. The exact clocking, voltage, timing, and pin-level requirements should be verified against the manufacturer datasheet and hardware design checklist before layout is released.
Typical uses include industrial Ethernet gateways, compact network switches, routers, telecommunications access equipment, set-top hardware, and embedded systems that require a single copper Ethernet port. Its 8 mm by 8 mm footprint saves board area compared with larger multi-port PHYs, while EEE and WoL features can improve power management and remote-access behavior.
PCB implementation requires careful attention to high-speed digital routing, clock integrity, copper media interface layout, and power and ground distribution. Follow the VSC8541 Hardware Design Checklist for recommended component placement, magnetics-interface geometry, decoupling, and signal-integrity practices. Confirm the selected transformer, line-side filtering, and board stack-up against the applicable channel requirements.
This product page combines the manufacturer feature description, package information, ordering-code comparisons, and practical implementation guidance. It also organizes same-family drop-in candidates and identifies which parameters still require confirmation from the individual device datasheet, helping engineers narrow a hardware revision or sourcing decision before completing a first-pass design.
Mga alternatibo na pwedeng ilagay na VSC8541XMV-04 — parehas na package, pin-to-pin na katugmang. Hindi kasama ang mga bahagi ng iba't-ibang package na nangangailangan ng pagpapaayos ng PCB.
Variante sa Seri na ito
Katulad na modelo sa serye na katugma sa pagpasok VSC8541XMV-04 (parehas na form factor at footprint) — pagkakaiba sa Energy Efficient Ethernet, Package, Product Type, Synchronous Ethernet, Package Dimensions.
VSC8541XMV-01
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →VSC8541XMV-02
✅ Drop-In ⚠️ Mga Talaan Hindi Naiwerikmo📋 Alternatibo na Reference (hindi sa katalogo)
VSC8541XMV-05
✅ Drop-In📋 Alternatibo na Reference (hindi sa katalogo)
VSC8541XMV
✅ Drop-In ⚠️ Mga Talaan Hindi NaiwerikmoMagkontak para sa presyo
Tingnan ang Datasheet →VSC8541XMV-04 Mga Spesipikasyon
| Device Type | Single-port copper Ethernet PHY |
| Supported Ethernet Rates | 10/100/1000BASE-T |
| Port Count | 1 copper port |
| Host Interface | GMII, RGMII, MII, and RMII |
| Energy Efficient Ethernet | Supported |
| Wake-on-LAN | Supported |
| Synchronous Ethernet | Supported |
| Packhaging | 68-QFN (8 mm x 8 mm) |
| Bilang ng Pin | 68 pins |
| Uri ng Pagpapasok | Surface mount |
| Maximum Link Rate | 1000 Mb/s |
| Media Interface | Copper twisted-pair Ethernet |
Gabay sa Pin Configuration ng VSC8541XMV-04 68-qfn (8 mm x 8 mm)
Pin configuration para sa VSC8541XMV-04 (68-qfn (8 mm x 8 mm) package). Ang pagnunumero ng pin, mga function, at connection diagram ay tinukoy sa datasheet ng manufacturer. Sumangguni dito para sa eksaktong footprint at mga alituntunin sa soldering.
Wala ng detalyadong pinout data na magagamit para sa VSC8541XMV-04.
Sumangguni sa datasheet para sa buong pin configuration.
Tipikal na mga Gamit
VSC8541XMV-04 ay nararapat para sa 6 aplikasyons: Industrial Ethernet Gateway, Compact Network Switch, Telecommunications Access Equipment, Networked Security Camera, Robotics and Automation Controller, Set-Top and Connected Media Device.
Industrial Ethernet Gateway
The VSC8541XMV-04 fits a compact industrial gateway that connects an embedded controller to a 10/100/1000BASE-T network. Its single copper-port architecture reduces board area compared with a multi-port PHY, while the 8 mm by 8 mm 68-QFN package supports dense equipment layouts. EEE can reduce link power when traffic is intermittent, and WoL supports remote maintenance. The design should use MII, RMII, RGMII, or GMII according to the host controller and must follow the manufacturer layout checklist for the magnetics interface and high-speed traces.
Inirekomenda
Compact Network Switch
The VSC8541XMV-04 can provide the copper-facing physical layer for a compact switch port in access equipment or an embedded network appliance. Support for 1000BASE-T allows the port to negotiate Gigabit operation over twisted-pair cabling, while GMII and RGMII offer parallel paths to a suitable switching fabric. The 68-QFN footprint leaves routing area for the network transformer and line-side components. EEE is useful in fanless equipment where link power can be reduced during low-traffic periods, subject to host and network configuration.
Inirekomenda
Telecommunications Access Equipment
The VSC8541XMV-04 is applicable to compact telecommunications equipment requiring one 10/100/1000BASE-T service port. Synchronous Ethernet support is particularly relevant to infrastructure designs that transfer timing over the Ethernet link, while Wake-on-LAN can assist remote maintenance of installed equipment. The 8 mm by 8 mm 68-QFN package supports space-constrained line cards, but synchronization mode, recovered clock architecture, line impedance, and isolation requirements must be confirmed in the device documentation and channel design.
Inirekomenda
Networked Security Camera
The VSC8541XMV-04 can serve as the copper Ethernet physical layer in a compact camera or surveillance endpoint. A single 10/100/1000BASE-T port supports common network architectures, and Energy Efficient Ethernet can reduce link energy consumption when the camera traffic stream is relatively static. Wake-on-LAN may support remote restart or maintenance functions when supported by the host stack. The camera design should pair the PHY with the approved magnetic network interface, observe high-speed trace-length constraints, and validate the complete link with the intended network transformer.
Inirekomenda
Robotics and Automation Controller
The VSC8541XMV-04 is suitable for a robot or industrial controller that needs a wired Ethernet link for configuration, telemetry, and process integration. The low-power, small-form-factor design aligns with embedded control boards where board area and standby consumption are constrained. The controller can use RMII or RGMII for a practical host connection and negotiate 10, 100, or 1000 Mb/s copper operation. Robust layout must separate the high-speed digital host interface from the line-side transformer network and provide the decoupling and return paths specified by the hardware design checklist.
Inirekomenda
Set-Top and Connected Media Device
The VSC8541XMV-04 fits a set-top box or connected media appliance requiring a single wired Gigabit Ethernet connection. Its compact 68-QFN package preserves board area for storage, video processing, and power systems, while EEE supports lower link power in a continuously connected product. RMII or RGMII provides integration options for embedded hosts with different clock and lane arrangements. The implementation should use the manufacturer’s approved magnetics and filtering approach, verify link startup behavior, and complete electromagnetic and conducted-emissions testing for the finished enclosure and cable configuration.
Inirekomenda
Buod ng mga Inirekomendang Produkto
Impormasyon ng Talumpati sa Engineering for VSC8541XMV-04 — ikabit, gabay sa disenyo, at impormasyon ng pagsunod sa kautusan.
Paunawang Hanapin
Ikabit sa Mga Alternatibo
| Parametro | Ito ang Producto | VSC8541XMV-01 | VSC8541XMV-02 | VSC8541XMV-05 | VSC8541XMV |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 68-QFN (8x8) | 68-QFN (8x8) | 68-QFN (8x8) | 68-QFN (8x8) | 68-QFN (8x8) |
| Port Count | 1 copper port | 1 copper port | 1 copper port | 1 copper port | 1 copper port |
| Supported Ethernet Rates | 10/100/1000BASE-T | 10/100/1000BASE-T | 10/100/1000BASE-T | 10/100/1000BASE-T | 10/100/1000BASE-T |
| Ordering Suffix | -04 | -01 | -02 | -05 | Base ordering code |
Pangunahing mga Pagkakaiba
- Combines Gigabit copper connectivity with compact integration (kumpara saKSZ8041TLI-TR)
- Multiple host-interface choices in one PHY family (kumpara saKSZ8081RNACA)
- Synchronization and remote-management features (kumpara saKSZ8041MLL-TR)
Talaan ng Disenyo
Follow the VSC8541 Hardware Design Checklist for the copper media interface, magnetics, filtering, decoupling, and component-placement scheme. Keep the host-side clocks and parallel data routes short and continuous, provide a low-impedance return path beneath each high-speed interface, and keep the line-side network physically separated from sensitive logic. Treat the checklist as a starting point, then validate the final stack-up and channel with simulation and hardware testing.
Confirm the exposed-pad, thermal, and pin-1 details from the package drawing before releasing artwork. The 68-QFN land pattern must match the manufacturer’s recommended footprint, and the exposed center pad should use the specified via and solder pattern. Also verify whether a particular ordering code or board revision changes any interface assignment; the family suffix alone is not sufficient evidence for a blind footprint reuse.
Maintain the timing and impedance constraints of the selected GMII, RGMII, MII, or RMII interface, including clock-to-data relationships and trace-length matching. Because these interfaces use parallel signals, route them as a coherent group over a continuous reference plane and avoid stubs or unnecessary test pads. Validate rise time, fall time, jitter, crosstalk, and channel margin on the final PCB rather than relying on nominal interface naming.
Do not substitute a different VSC8541 ordering suffix solely because the package name matches. Compare the exact device datasheet for interface enablement, register behavior, silicon revision, electrical limits, qualification, and documented changes. Similarly, do not assume that Wake-on-LAN, EEE, or Synchronous Ethernet are automatically available in every operating mode; confirm the required software, clocks, magnetics, and system configuration.
Impormasyon ng Pagsunod sa Kautusan
The manufacturer feature description and exact-part distributor listings do not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations for VSC8541XMV-04. Confirm these statements against the current manufacturer product documentation and the applicable quality document.