VSC8541XMV-04 Single-Port Gigabit Cu PHY | Microchip
Référence : VSC8541XMV-04 ✓ ActifVSC8541XMV-04 Présentation
A copper PHY, or physical-layer transceiver, is the circuit that converts logical Ethernet data into signals suitable for transmission over twisted-pair cabling. Within the network hierarchy, the VSC8541XMV-04 is an Ethernet interface IC that connects a digital network processor, switch, router, or other host controller to a 10/100/1000BASE-T copper network. Its multiple interface options allow it to address systems with different clocking, data-width, and board-layout requirements.
The device combines Gigabit-class network connectivity with low-power operation and a compact 68-QFN package. Energy Efficient Ethernet can reduce link power when the traffic load permits it, while Wake-on-LAN supports remotely waking compatible networked equipment. Synchronous Ethernet provides a mechanism for transferring timing information over Ethernet links, making the PHY relevant to infrastructure equipment that requires synchronization.
The available GMII, RGMII, MII, and RMII interfaces are important selection criteria because they determine how the PHY connects to the host controller. GMII and RGMII support parallel Ethernet signaling, while MII and RMII are commonly associated with lower-speed or lower-pin-count implementations. The exact clocking, voltage, timing, and pin-level requirements should be verified against the manufacturer datasheet and hardware design checklist before layout is released.
Typical uses include industrial Ethernet gateways, compact network switches, routers, telecommunications access equipment, set-top hardware, and embedded systems that require a single copper Ethernet port. Its 8 mm by 8 mm footprint saves board area compared with larger multi-port PHYs, while EEE and WoL features can improve power management and remote-access behavior.
PCB implementation requires careful attention to high-speed digital routing, clock integrity, copper media interface layout, and power and ground distribution. Follow the VSC8541 Hardware Design Checklist for recommended component placement, magnetics-interface geometry, decoupling, and signal-integrity practices. Confirm the selected transformer, line-side filtering, and board stack-up against the applicable channel requirements.
This product page combines the manufacturer feature description, package information, ordering-code comparisons, and practical implementation guidance. It also organizes same-family drop-in candidates and identifies which parameters still require confirmation from the individual device datasheet, helping engineers narrow a hardware revision or sourcing decision before completing a first-pass design.
Alternatives de remplacement direct pour VSC8541XMV-04 — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
Variantes de cette série
Modèles de la même série directement compatibles avec VSC8541XMV-04 (même facteur de forme et même empreinte) — différant par Energy Efficient Ethernet, Package, Product Type, Synchronous Ethernet, Package Dimensions.
VSC8541XMV-01
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →VSC8541XMV-02
✅ Remplacement direct ⚠️ Spécifications non vérifiées📋 Alternative de référence (hors catalogue)
VSC8541XMV-05
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
VSC8541XMV
✅ Remplacement direct ⚠️ Spécifications non vérifiéesContactez-nous pour le prix
Voir la fiche technique →VSC8541XMV-04 Spécifications
| Device Type | Single-port copper Ethernet PHY |
| Supported Ethernet Rates | 10/100/1000BASE-T |
| Port Count | 1 copper port |
| Host Interface | GMII, RGMII, MII, and RMII |
| Energy Efficient Ethernet | Supported |
| Wake-on-LAN | Supported |
| Synchronous Ethernet | Supported |
| Boîtier | 68-QFN (8 mm x 8 mm) |
| Nombre de broches | 68 pins |
| Type de montage | Surface mount |
| Maximum Link Rate | 1000 Mb/s |
| Media Interface | Copper twisted-pair Ethernet |
Guide de configuration des broches du VSC8541XMV-04 68-qfn (8 mm x 8 mm)
Configuration des broches du VSC8541XMV-04 (boîtier 68-qfn (8 mm x 8 mm)). La numérotation des broches, les fonctions et les schémas de connexion sont définis dans la fiche technique du fabricant. Consultez-la pour l'empreinte exacte et les directives de soudage.
Aucune donnée de brochage détaillée disponible pour VSC8541XMV-04.
Consultez la fiche technique pour la configuration complète des broches.
Applications typiques
VSC8541XMV-04 convient pour 6 applications: Industrial Ethernet Gateway, Compact Network Switch, Telecommunications Access Equipment, Networked Security Camera, Robotics and Automation Controller, Set-Top and Connected Media Device.
Industrial Ethernet Gateway
The VSC8541XMV-04 fits a compact industrial gateway that connects an embedded controller to a 10/100/1000BASE-T network. Its single copper-port architecture reduces board area compared with a multi-port PHY, while the 8 mm by 8 mm 68-QFN package supports dense equipment layouts. EEE can reduce link power when traffic is intermittent, and WoL supports remote maintenance. The design should use MII, RMII, RGMII, or GMII according to the host controller and must follow the manufacturer layout checklist for the magnetics interface and high-speed traces.
Recommandé
Compact Network Switch
The VSC8541XMV-04 can provide the copper-facing physical layer for a compact switch port in access equipment or an embedded network appliance. Support for 1000BASE-T allows the port to negotiate Gigabit operation over twisted-pair cabling, while GMII and RGMII offer parallel paths to a suitable switching fabric. The 68-QFN footprint leaves routing area for the network transformer and line-side components. EEE is useful in fanless equipment where link power can be reduced during low-traffic periods, subject to host and network configuration.
Recommandé
Telecommunications Access Equipment
The VSC8541XMV-04 is applicable to compact telecommunications equipment requiring one 10/100/1000BASE-T service port. Synchronous Ethernet support is particularly relevant to infrastructure designs that transfer timing over the Ethernet link, while Wake-on-LAN can assist remote maintenance of installed equipment. The 8 mm by 8 mm 68-QFN package supports space-constrained line cards, but synchronization mode, recovered clock architecture, line impedance, and isolation requirements must be confirmed in the device documentation and channel design.
Recommandé
Networked Security Camera
The VSC8541XMV-04 can serve as the copper Ethernet physical layer in a compact camera or surveillance endpoint. A single 10/100/1000BASE-T port supports common network architectures, and Energy Efficient Ethernet can reduce link energy consumption when the camera traffic stream is relatively static. Wake-on-LAN may support remote restart or maintenance functions when supported by the host stack. The camera design should pair the PHY with the approved magnetic network interface, observe high-speed trace-length constraints, and validate the complete link with the intended network transformer.
Recommandé
Robotics and Automation Controller
The VSC8541XMV-04 is suitable for a robot or industrial controller that needs a wired Ethernet link for configuration, telemetry, and process integration. The low-power, small-form-factor design aligns with embedded control boards where board area and standby consumption are constrained. The controller can use RMII or RGMII for a practical host connection and negotiate 10, 100, or 1000 Mb/s copper operation. Robust layout must separate the high-speed digital host interface from the line-side transformer network and provide the decoupling and return paths specified by the hardware design checklist.
Recommandé
Set-Top and Connected Media Device
The VSC8541XMV-04 fits a set-top box or connected media appliance requiring a single wired Gigabit Ethernet connection. Its compact 68-QFN package preserves board area for storage, video processing, and power systems, while EEE supports lower link power in a continuously connected product. RMII or RGMII provides integration options for embedded hosts with different clock and lane arrangements. The implementation should use the manufacturer’s approved magnetics and filtering approach, verify link startup behavior, and complete electromagnetic and conducted-emissions testing for the finished enclosure and cable configuration.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour VSC8541XMV-04 — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | VSC8541XMV-01 | VSC8541XMV-02 | VSC8541XMV-05 | VSC8541XMV |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 68-QFN (8x8) | 68-QFN (8x8) | 68-QFN (8x8) | 68-QFN (8x8) | 68-QFN (8x8) |
| Port Count | 1 copper port | 1 copper port | 1 copper port | 1 copper port | 1 copper port |
| Supported Ethernet Rates | 10/100/1000BASE-T | 10/100/1000BASE-T | 10/100/1000BASE-T | 10/100/1000BASE-T | 10/100/1000BASE-T |
| Ordering Suffix | -04 | -01 | -02 | -05 | Base ordering code |
Principaux différenciateurs
- Combines Gigabit copper connectivity with compact integration (vs KSZ8041TLI-TR)
- Multiple host-interface choices in one PHY family (vs KSZ8081RNACA)
- Synchronization and remote-management features (vs KSZ8041MLL-TR)
Notes de conception
Follow the VSC8541 Hardware Design Checklist for the copper media interface, magnetics, filtering, decoupling, and component-placement scheme. Keep the host-side clocks and parallel data routes short and continuous, provide a low-impedance return path beneath each high-speed interface, and keep the line-side network physically separated from sensitive logic. Treat the checklist as a starting point, then validate the final stack-up and channel with simulation and hardware testing.
Confirm the exposed-pad, thermal, and pin-1 details from the package drawing before releasing artwork. The 68-QFN land pattern must match the manufacturer’s recommended footprint, and the exposed center pad should use the specified via and solder pattern. Also verify whether a particular ordering code or board revision changes any interface assignment; the family suffix alone is not sufficient evidence for a blind footprint reuse.
Maintain the timing and impedance constraints of the selected GMII, RGMII, MII, or RMII interface, including clock-to-data relationships and trace-length matching. Because these interfaces use parallel signals, route them as a coherent group over a continuous reference plane and avoid stubs or unnecessary test pads. Validate rise time, fall time, jitter, crosstalk, and channel margin on the final PCB rather than relying on nominal interface naming.
Do not substitute a different VSC8541 ordering suffix solely because the package name matches. Compare the exact device datasheet for interface enablement, register behavior, silicon revision, electrical limits, qualification, and documented changes. Similarly, do not assume that Wake-on-LAN, EEE, or Synchronous Ethernet are automatically available in every operating mode; confirm the required software, clocks, magnetics, and system configuration.
Informations de conformité
The manufacturer feature description and exact-part distributor listings do not provide explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations for VSC8541XMV-04. Confirm these statements against the current manufacturer product documentation and the applicable quality document.