Ürünler (46.000+)

LAN9118-MT 10/100 Ethernet Controller | Microchip
LAN9118-MT

LAN9118-MT 10/100 Ethernet Controller | Microchip

The Microchip Technology LAN9118-MT is a single-chip 10/100 Base-T/TX Ethernet controller with a 32-bit external parallel interface, a 3.3 V supply, and a 100-pin TQFP package. It combines an Ethernet controller and PHY for embedded systems requiring local network connectivity without a separate PCI bus controller. The device supports 10 Mbps and 100 Mbps Ethernet operation and is identified by the commercial temperature-grade -MT ordering suffix. An Ethernet controller is an interface integrated circuit that connects an embedded processor or microcontroller to a physical Ethernet network. The LAN9118 family belongs to the broader hierarchy of Ethernet controller -> network interface controller -> interface IC -> semiconductor. Integrating the controller and PHY supports embedded product designs for industrial controls, communications equipment, data acquisition, and networked peripherals, while the parallel host interface gives the host processor direct register and data access. The verified product information identifies a 32-bit external data bus, a 7-bit address bus, a 25 MHz clock capability, a 3.3 V supply, and a 100-pin TQFP package. The 100-pin package exposes the substantial parallel host interface required by the non-PCI architecture. The LAN9118-MT is therefore most appropriate where an embedded system has enough I/O and board area for a high-pin-count parallel interface rather than a compact serial Ethernet controller. The part is described as a high-performance single-chip 10/100 non-PCI Ethernet controller. Its combined controller and PHY architecture can reduce the number of external network-interface components compared with a separated MAC and physical-layer design. Ethernet magnetics and the RJ45 connector remain external, and the final signal-integrity and layout implementation must follow the manufacturer hardware guidance. The provided verification also identifies IEEE 802.3 and IEEE 802.3u compliance in a product comparison source. Typical uses include embedded Ethernet gateways, industrial monitoring equipment, serial-to-Ethernet systems, test instruments, and control systems that require 10/100 connectivity. The parallel interface makes the LAN9118-MT most attractive to designs with a processor bus capable of supporting the required data width and pin count. It is less suitable for highly constrained systems that favor a serial Ethernet interface or a smaller package. Designers should verify the complete pinout, voltage tolerances, clock requirements, decoupling, reset behavior, magnetics selection, and PCB routing against the manufacturer datasheet before layout release. The verified search results identify the manufacturer LAN9118 product page and multiple datasheet mirrors, but do not provide every electrical timing, pin-level, or lifecycle value needed for a complete production design.

RFQ İletişim
LAN91C100FDTQFP - 10/100 Ethernet MAC Controller | Microchip
LAN91C100FDTQFP

LAN91C100FDTQFP - 10/100 Ethernet MAC Controller | Microchip

The Microchip Technology LAN91C100FDTQFP is a single-chip 10/100 Mb/s Ethernet Media Access Controller with an integrated Media Independent Interface, designed for first-generation Fast Ethernet adapters and embedded connectivity products. It is packaged in a 208-pin TQFP measuring 28 x 28 mm and uses CMOS technology. The controller supports IEEE 802.3 Ethernet operation, full-duplex capability, and an integrated 10/100 Ethernet MAC with MII connectivity. An Ethernet MAC controller is an interface IC that manages frame transmission, reception, address filtering, and access to the physical network medium. In the product hierarchy, the LAN91C100FDTQFP belongs to Ethernet controllers, within interface ICs and semiconductors. Its MII provides a standardized digital connection to an external Ethernet PHY, allowing system designers to separate network-medium conversion from MAC processing while retaining flexibility in magnetics and transceiver selection. Key characteristics include support for 10 Mb/s and 100 Mb/s Ethernet, IEEE 802.3 operation, full-duplex capability, commercial-temperature construction, and low-power shutdown. The MII interface makes the device suitable for embedded systems, industrial controllers, print servers, set-top equipment, and other legacy Fast Ethernet products that were designed around a dedicated MAC rather than an integrated Ethernet transceiver. Because the MAC does not include the physical-layer circuitry, the board still requires a compatible 10/100 Ethernet PHY and the associated magnetics and network interface components. The LAN91C100FDTQFP was developed for first-generation Fast Ethernet adapter designs, where implementation flexibility and external PHY selection were priorities. Its 208-pin package provides a broad set of parallel host and MII signals, while the large lead count makes careful high-speed trace routing, plane use, and ground-return design important. The controller operates from a digital CMOS environment, and its shutdown capability can reduce power consumption when the attached system does not require continuous network connectivity. Typical deployments include embedded industrial Ethernet equipment, legacy network adapters, printers, multifunction peripherals, embedded control systems, and purpose-built communication appliances. The controller is most appropriate when the host processor requires a dedicated Ethernet MAC but the product specification allows use of an external PHY. It is less attractive for new compact designs where an integrated MAC-and-PHY device would reduce board area, component count, and design effort. For implementation, follow the pin-description and reference-circuit tables in the manufacturer datasheet when assigning every ball or lead and selecting bypass capacitance. Preserve continuous ground-plane returns beneath the high-speed MII and host interface paths, terminate unused inputs according to the device requirements, and validate signal integrity with the selected PHY and board stack-up. This product page combines device identification, interface guidance, comparison considerations, and sourcing support to support legacy Fast Ethernet design work.

RFQ İletişim
LAN91C110-PU - 10/100 Ethernet Controller | Microchip
LAN91C110-PU

LAN91C110-PU - 10/100 Ethernet Controller | Microchip

The Microchip LAN91C110-PU is a 10/100 Base-TX Fast Ethernet controller with a generic 16/32-bit host interface, packaged in a 144-pin TQFP measuring 20 mm by 20 mm. It is designed for second-generation Fast Ethernet PC Card adapters and other non-PCI connectivity products. The controller implements the Media Access Control portion of the Ethernet protocol, placing Ethernet framing and medium-access functions in a dedicated interface IC. An Ethernet controller is a semiconductor that manages frame transmission and reception between a host processor and a network medium. The LAN91C110-PU provides a hardware interface suitable for systems whose CPU or system bus is not based on PCI. By using a generic parallel host interface, it can be connected to compatible processors and bus bridges without requiring a PCI-specific interface architecture. The principal feature set includes support for 10/100 Base-T/TX networking, a selectable 16-bit or 32-bit host interface, and an integrated Ethernet MAC function. The parallel interface provides a practical connection point for embedded systems, industrial controllers, legacy computer systems, and custom communications equipment. Its 144-pin TQFP package supports the numerous digital host, clock, reset, media, and power connections required by the controller and its external physical-layer interface. The LAN91C110-PU separates network-medium handling from the host-side system bus. The MAC processes Ethernet frame activity while the generic 16/32-bit interface transfers control and data information to the host processor. This division of responsibilities is particularly useful when a system already has an established embedded bus architecture but requires standards-based 10/100 Ethernet connectivity rather than a PCI peripheral arrangement. Typical applications include Fast Ethernet PC Card adapters, embedded control systems, industrial data-acquisition equipment, legacy network upgrades, and custom host-bus designs. It can also suit embedded Linux platforms and other processor-based equipment requiring a parallel Ethernet connection. System-level clocking, physical-layer connectivity, magnetic-interface components, and host-bus timing remain part of the complete design rather than functions implied solely by the controller IC. Designers should review the manufacturer datasheet before assigning signals because the complete 144-pin assignment, operating limits, interface timing, clock requirements, and recommended external networks must be followed exactly. PCB layout should preserve the required short paths, appropriate grounding, and controlled clock and data-routing geometry. Host firmware must also initialize the controller and configure its medium-access and host-interface operation according to the manufacturer procedure. This page organizes the confirmed device identity, package information, host-interface capabilities, use cases, sourcing path, and design considerations into an engineering-focused reference. It also distinguishes the controller's documented role from the additional PHY, magnetics, firmware, and bus-interface engineering required to build a complete Ethernet-connected product.

RFQ İletişim
LAN91C111-NC 10/100 Ethernet MAC/PHY | Microchip Technology
LAN91C111-NC

LAN91C111-NC 10/100 Ethernet MAC/PHY | Microchip Technology

The Microchip Technology LAN91C111-NC is a mixed-signal Ethernet interface IC that integrates a 10/100 Mbps Media Access Controller and Physical Layer in a 128-pin TQFP package. It supports 32-bit, 16-bit, and 8-bit host bus configurations, provides a MII interface, and includes 8 KB of dynamically configurable transmit and receive FIFO memory for embedded Ethernet designs. An Ethernet MAC-and-PHY controller provides the bridge between a host processor and a physical network connection. The MAC manages frame handling and CSMA/CD access, while the integrated PHY handles the physical signaling required for 10BASE-T or 100BASE-TX links. Integrating both functions into one device reduces component count and allows a host processor to connect to copper Ethernet without requiring a separate transceiver. The LAN91C111-NC supports data rates of 10 Mbps and 100 Mbps and implements the MAC and PHY portions of the CSMA/CD protocol. Its host interface can operate with 32-bit, 16-bit, or 8-bit data widths, helping the device accommodate processors with different bus capabilities. The internal MII connection between the MAC and PHY helps maintain throughput without using a separate external PHY bus. Internal transmit and receive FIFO memory is dynamically configurable and totals 8 KB. This buffering allows the host interface and Ethernet network activity to proceed at different effective rates, improving tolerance of host-bus access intervals. The MII interface also provides a standardized connection for additional physical-layer equipment and simplifies integration with related network-interface circuitry. Typical uses include industrial embedded systems, factory automation equipment, building controls, test equipment, print controllers, and compact embedded servers. A 100 Mbps link provides sufficient bandwidth for supervisory data, configuration traffic, telemetry, and moderate local file transfer. The selectable host-bus width is especially useful when adapting the controller to legacy parallel processor buses. The principal design task is matching the host-bus timing, interrupt structure, address mapping, and I/O voltage to the system processor. Place the device and its required external network components close together, route MII and host signals as controlled-impedance traces, and terminate unused inputs according to the manufacturer datasheet. Validate signal integrity and recovery behavior across the full set of line-rate and environmental conditions. This product record combines the Ethernet function description, package details, sourcing guidance, practical PCB considerations, and application-specific engineering context. It also distinguishes the device from true pin-compatible alternatives by applying a strict same-package and pin-compatibility requirement rather than presenting merely similar Ethernet controllers.

RFQ İletişim
LAN91C111-NE - 10/100 Ethernet MAC + PHY | Microchip
LAN91C111-NE

LAN91C111-NE - 10/100 Ethernet MAC + PHY | Microchip

The Microchip LAN91C111-NE is a single-chip 10/100 Ethernet controller integrating a Media Access Control layer and Physical Layer in a mixed-signal Analog/Digital device. It supports 10 Mbps and 100 Mbps operation, configurable 32-bit, 16-bit, or 8-bit host interfaces, full-duplex switched Ethernet, and 8 KB of dynamically configurable transmit and receive FIFO memory. The device uses an IEEE 802.3-compatible Ethernet architecture for embedded systems. An Ethernet MAC and PHY combined on one IC form the interface between an embedded host processor and a physical copper network. The MAC manages frame processing, addressing, collision handling, and data movement, while the PHY converts logical data into signals that can be transmitted over twisted-pair Ethernet. Integrating both functions reduces external component count and simplifies PCB routing compared with a separated MAC and transceiver design. The LAN91C111 family provides dual-speed 10/100 Mbps connectivity, AutoNegotiation, burst data transfer, and selectable host-bus widths. Its 8 KB internal FIFO buffer separates host processing from Ethernet timing, helping manage burst traffic on embedded processor buses. The flexible 8-, 16-, or 32-bit host interface allows the same controller architecture to address systems with different data-bus capabilities. The controller implements the MAC and PHY portions of the CSMA/CD protocol. Its receive path aligns scrambled data to IEEE 802.3 5B word boundaries, descrambles the recovered data, and transfers it to the 4B/5B decoder. On the transmit side, the integrated Ethernet engine prepares frames for the physical layer while the internal FIFOs buffer host and network traffic. This architecture supports both 10 Mbps and 100 Mbps links without requiring a separate Ethernet interface controller. Typical uses include embedded industrial controllers, factory automation equipment, embedded Web servers, set-top boxes, print systems, and network-connected embedded products. It is particularly useful where a host processor needs compact 10/100 Ethernet connectivity without a PCI bus or a separate physical-layer transceiver. The selectable host width also helps optimize external bus wiring and processor interface overhead. PCB design should preserve short, controlled impedance Ethernet traces and provide the external magnetic-interface components required by the application circuitry. Place the controller and supporting clock, decoupling, and interface components according to the manufacturer datasheet layout. Check the host-bus voltage, reset requirements, interrupt connections, and FIFO configuration in firmware before finalizing the system interface. This page combines the manufacturer architecture description with practical interface guidance, verified MPN comparison points, and implementation-oriented design notes. It is structured to help engineers identify the correct LAN91C111 ordering variant, plan the host interface, and evaluate the controller for compact embedded Ethernet designs.

RFQ İletişim
LAN91C111-NS - 10/100 Ethernet MAC+PHY | Microchip
LAN91C111-NS

LAN91C111-NS - 10/100 Ethernet MAC+PHY | Microchip

Microchip Technology LAN91C111-NS is a mixed-signal 10/100 Mb/s Ethernet controller integrating a Media Access Controller and Physical Layer in a 128-pin QFP package. It implements the MAC and PHY portions of the CSMA/CD protocol, supports 10 Mbps and 100 Mbps operation, and provides a parallel host interface selectable as 32-bit, 16-bit, or 8-bit. An Ethernet MAC and PHY controller is an integrated network interface for embedded equipment. The MAC manages frame handling and the CSMA/CD protocol, while the PHY connects the digital controller to a 10/100 Base-T Ethernet physical layer. Combining both functions reduces system complexity, conserves board area, and allows an embedded processor to communicate through a parallel host bus rather than requiring a separate Ethernet PHY. The LAN91C111-NS supports dual-speed operation at 100 Mbps or 10 Mbps with AutoNegotiation, as described in the manufacturer application note. Its architecture includes 8 KB of dynamically configurable transmit and receive FIFO SRAM, helping decouple host-bus traffic from network-frame activity. The parallel interface can operate at 32, 16, or 8 bits, providing flexibility for embedded processors with different external-bus capabilities. For 100BASE-TX operation, the descrambler processes the scrambled data recovered from the medium, follows the IEEE 802.3 scrambling rules, aligns the data on correct 5B word boundaries, and passes it to the 4B5B decoder. This mixed-signal architecture supports both 10BASE-T and 100BASE-TX networking while maintaining a host-facing digital interface. The manufacturer identifies the device as suitable for third-generation embedded Fast Ethernet connectivity solutions. Typical uses include industrial automation controllers, embedded network gateways, factory data-acquisition equipment, building-control systems, print servers, and compact network-access appliances. The selectable host-bus width is especially useful when balancing throughput, PCB routing, and processor-bus compatibility. AutoNegotiation allows the controller to operate with 10 Mb/s or 100 Mb/s network links while reducing manual speed configuration. Design the power, ground, clock, magnetics, and network-line interface according to the manufacturer reference implementation. Preserve the recommended placement and decoupling of the Ethernet magnetic components and provide the specified oscillator and crystal arrangement to avoid timing or compliance problems. Validate the completed board for conducted emissions, immunity, and Ethernet link performance before production. This page organizes the controller's principal network functions, interface options, package characteristics, application guidance, and qualified same-footprint alternatives. It also highlights design considerations that help engineers distinguish protocol coverage, host-bus flexibility, FIFO behavior, and physical-layer implementation without treating the device as a generic Ethernet block.

RFQ İletişim
LAN91C111-NU - 10/100 Ethernet MAC/PHY | Microchip
LAN91C111-NU

LAN91C111-NU - 10/100 Ethernet MAC/PHY | Microchip

The Microchip LAN91C111-NU is a single-chip 10/100 Base-T Ethernet controller integrating a Media Access Control layer and Physical Layer in a 128-lead TQFP package. It supports 10 Mbps and 100 Mbps operation, provides an 8/16/32-bit parallel host interface, and includes an 8 KB dynamically configurable transmit and receive FIFO. The device combines digital host-facing logic with analog PHY functions for embedded Ethernet connectivity. An Ethernet MAC and PHY are the two principal layers required for a conventional 10/100 Ethernet connection. The MAC organizes frames and manages access to the network, while the PHY converts digital data into signals suitable for twisted-pair cabling. Integrating both functions into one controller reduces external component count and simplifies embedded network designs compared with separate MAC and PHY implementations. The LAN91C111-NU belongs to the broader interface IC and Ethernet controller hierarchy. Key features include 10/100 Mbps dual-speed operation, support for 8-bit, 16-bit, and 32-bit host bus configurations, and 8 KB of internal FIFO memory. The manufacturer describes the LAN91C111 as implementing the MAC and PHY portions of CSMA/CD and using a parallel host interface suited to embedded processors. Its mixed-signal construction places network termination and transceiver functions alongside the digital controller logic. The configurable host interface allows a design to balance throughput, wiring, and memory efficiency. An 8-bit bus can reduce the number of processor connections, while a 32-bit bus can transfer data more efficiently when the host bus and system timing support it. The internal transmit and receive FIFOs help decouple host access from network timing, although firmware, interrupt handling, and buffer configuration remain essential parts of a reliable driver design. Typical applications include embedded industrial controllers, print servers, set-top boxes, embedded Linux systems, instrument-control equipment, and compact network appliances. The integrated 10/100 Ethernet interface is useful when a system needs a deterministic parallel host connection rather than a serial network interface. It can also support legacy Fast Ethernet equipment where both 10 Mbps and 100 Mbps operation are required. Layout is the primary design consideration. Place the Ethernet magnetics, line-side protection, and PHY-related components close to the network connector, while keeping the parallel host bus away from sensitive analog network traces. Confirm power, clock, reset, transceiver, and host-interface requirements against the manufacturer datasheet before releasing the PCB layout. The package library does not contain a dedicated 128-lead TQFP drawing, so use the manufacturer pin-description table for assignments. This page combines the LAN91C111-NU device function, verified family variants, cross-reference findings, application guidance, and practical integration considerations. It also distinguishes true same-package options from unrelated Ethernet controllers that may require different hosts, PHYs, packages, or driver changes.

RFQ İletişim
LAN91C111I-NU-E2 - 10/100 Ethernet Controller | SMSC
LAN91C111I-NU-E2

LAN91C111I-NU-E2 - 10/100 Ethernet Controller | SMSC

The SMSC Corporation LAN91C111I-NU-E2 is a single-chip 10/100 Ethernet controller with an integrated physical layer, parallel host interface, and non-PCI architecture, housed in a 128-pin TQFP package measuring 14 x 14 mm. It supports 10 Mbps and 100 Mbps Ethernet operation according to IEEE 802.3 and IEEE 802.3u, while operating from a 2.97 V to 3.63 V core supply. An Ethernet controller is an interface integrated circuit that connects an embedded processing system to a physical Ethernet network. In the hierarchy, the LAN91C111 belongs to Ethernet controllers, interface ICs, integrated circuits, and semiconductors. Integrating the MAC and PHY reduces the number of components required for an embedded Fast Ethernet port, while the parallel interface provides direct access between the controller and external host-bus circuitry. The LAN91C111 uses a four-bit Media Independent Interface for connections to either 10 Mbps or 100 Mbps Ethernet networks. Three device pins support the two-wire serial MII management protocol. This combination allows the controller to participate in MII-based network designs without requiring the parallel interface to be limited to one Ethernet speed. The controller is intended for embedded systems requiring dedicated Fast Ethernet connectivity rather than a PCI-based desktop adapter. The device is identified as a 10/100 Base-T/TX PHY controller with a parallel host interface. Its 128-TQFP package provides the mixed-signal and digital connections needed for the MAC, PHY, host interface, and MII functions. Because it combines analog and digital circuitry on one device, PCB implementation requires controlled trace routing, suitable grounding, and careful separation of high-speed digital signals from sensitive network and clock connections. Typical applications include embedded industrial controllers, test equipment, print servers, communications appliances, and other systems requiring a compact 10/100 Ethernet interface. The integrated MAC and PHY are especially useful when a system cannot accommodate a discrete Ethernet PHY or a separate PCI Ethernet controller. The parallel host interface must still be matched carefully to the target processor, bus logic, and firmware architecture. When designing around the LAN91C111I-NU-E2, verify the host-bus timing, MII connections, magnetic-interface implementation, and available board area before releasing a PCB layout. The 128-pin package is not physically interchangeable with smaller Ethernet interfaces without a complete board redesign, so footprint and firmware compatibility are as important as nominal Ethernet performance. This page combines the manufacturer interface information, package identification, ordering details, and engineering guidance for the LAN91C111I-NU-E2. It also documents the distinctions among related LAN91C111 ordering codes and provides practical considerations for evaluating this non-PCI Ethernet controller in an embedded Fast Ethernet design.

RFQ İletişim
LAN91C113-NC 10/100 Ethernet MAC/PHY | Microchip Technology
LAN91C113-NC

LAN91C113-NC 10/100 Ethernet MAC/PHY | Microchip Technology

The Microchip Technology LAN91C113-NC is a 16-bit 10/100 Base-T Ethernet single-chip MAC and PHY controller. It combines media-access control, physical-layer signaling, and a parallel host interface in one integrated circuit, reducing the component count required for embedded Ethernet connectivity. The controller is associated with the SMSC FEAST family and is identified in the manufacturer catalog as LAN91C113. An Ethernet MAC and PHY single-chip controller is an interface IC that connects an embedded host processor to a copper Ethernet network. The MAC handles Ethernet frame processing and host-facing data exchange, while the PHY converts between digital signaling and the physical signals used on 10/100 Base-T networks. In the broader semiconductor hierarchy, the device belongs to Ethernet controllers, interface controllers, integrated circuits, and networked embedded systems. The principal feature of the LAN91C113-NC is its combination of a 16-bit parallel host interface with an integrated 10/100 Ethernet MAC and PHY. This integration can simplify embedded networking designs that previously required separate Ethernet controller and physical-layer devices. The 16-bit interface provides a direct path between the controller and a compatible host processor, while on-chip Ethernet physical-layer functionality supports connection to a network transformer and magnetics. The LAN91C113 family is associated with SMSC's FEAST Fast Ethernet controller technology. Its architecture is intended to provide Ethernet connectivity in embedded systems where a non-PCI parallel interface is preferable to a PCI-based controller. The combined MAC and PHY arrangement also reduces board-level integration complexity by consolidating the digital controller and physical-layer transceiver into one package. Typical uses for this controller include industrial embedded platforms, data acquisition equipment, communications modules, embedded test systems, and legacy controller-based products being connected to 10/100 Ethernet. It is particularly relevant when the host processor already provides a 16-bit parallel bus and the design needs a dedicated Ethernet interface rather than an integrated network controller in the processor itself. Design work should begin with the manufacturer pin-description and reference-circuit sections, including the external clock, reset, magnetics, decoupling, and network-isolation requirements. PCB signal integrity is particularly important because the device combines parallel host signaling with Ethernet physical circuitry. Maintain the specified component placement and controlled impedance around the Ethernet network path, and use the manufacturer reference design as the basis for a first revision. This product page combines the device identity, catalog description, distributor records, package guidance, application analysis, and engineering design notes into one purchasing resource. It also distinguishes direct ordering information from replacement analysis so engineers can assess fit, interface compatibility, and board-level integration before committing a design.

RFQ İletişim
LAN91C113-NE - 10/100 Ethernet MAC PHY | SMSC
LAN91C113-NE

LAN91C113-NE - 10/100 Ethernet MAC PHY | SMSC

The SMSC LAN91C113-NE is a highly integrated 10/100 Ethernet MAC and PHY solution for embedded networking, with support for 10Base-T and 100Base-TX Ethernet applications. It combines a 10/100 Ethernet Media Access Controller with a physical-layer transceiver in one device, reducing the component count and simplifying the hardware architecture of embedded network equipment. The LAN91C113-NE is associated with a 128-lead TQFP package configuration for compact surface-mount PCB designs. An Ethernet MAC is the controller that manages frame transmission and reception between a host processor and the physical network medium. The PHY converts digital data into the electrical signaling required by 10Base-T and 100Base-TX Ethernet. Integrating both functions in one IC gives embedded designers a single network interface component that connects to a host system through a parallel interface and uses standard Ethernet magnetics and cabling for the physical network connection. The LAN91C113-NE is positioned for designs requiring 10/100 Ethernet connectivity rather than gigabit Ethernet. It can support industrial controllers, embedded gateways, print servers, set-top equipment, test instruments, and other network-enabled products. Because the MAC and PHY are combined, board designers can reduce the number of separate network-interface ICs and simplify the relationship between software control, packet handling, and physical-layer signaling. In a typical embedded design, the host processor connects to the LAN91C113-NE for frame exchange, while the Ethernet PHY section connects through the required external network interface components. The device is intended for 10Base-T and 100Base-TX links, making it appropriate for legacy and cost-sensitive Ethernet installations where 100 Mbit/s operation is sufficient. Software drivers and host-side configuration are necessary to initialize the controller and manage Ethernet traffic. The principal engineering consideration is interface and system integration. The design must provide the correct power rails, decoupling, clocking, reset behavior, host-bus connections, and Ethernet magnetic interface required by the selected board architecture. Pin assignment, voltage levels, timing, and exposed-package details should be confirmed against the manufacturer datasheet before the PCB footprint is released. LAN91C113-NE is a practical choice when an embedded product needs a dedicated 10/100 Ethernet MAC-PHY with a parallel host interface in a surface-mount package. Its value comes from combining controller and transceiver functions, reducing board complexity while retaining support for both 10Base-T and 100Base-TX network operation. This product summary combines the manufacturer product information and distributor references for the LAN91C113-NE. The Request a Quote form on this page is the appropriate route for current commercial availability, pricing, and delivery information.

RFQ İletişim
LAN91C113-NS - 100Mbps Ethernet Controller | Microchip
LAN91C113-NS

LAN91C113-NS - 100Mbps Ethernet Controller | Microchip

Microchip Technology LAN91C113-NS is a 100 Mbps Ethernet controller with integrated 10/100 Base-T/TX PHY and a parallel MII interface, supplied in a 128-QFP package. The device supports a 2.97 V minimum supply voltage, operates at 3.3 V, and is specified for a 0°C to 85°C temperature range. Its integrated MAC and PHY combine Ethernet packet processing and physical-layer connectivity in one IC. An Ethernet controller is an interface integrated circuit that connects a digital processor or system bus to an Ethernet network. The LAN91C113 belongs to the Ethernet interface controller category, which combines a media access controller, physical-layer transceiver, and host-facing parallel interface. This integration can reduce the number of external network components while providing a standardized 10/100 Ethernet connection for embedded equipment. The principal operating characteristics are a 100 Mbps data rate, compliance with IEEE 802.3 and IEEE 802.3u, MII host connectivity, and a 3.3 V supply. The listed supply current is 100 mA, while the operating temperature extends from 0°C to 85°C. These specifications position the device for industrial, communications, and embedded systems that use a parallel host interface instead of a serial media interface. The 128-QFP package provides the physical footprint and pin count needed for a substantial mixed-signal Ethernet interface. Because the MAC and PHY are integrated, PCB design requires careful separation of Ethernet signal routing, supply distribution, and grounding. The parallel MII interface should be routed according to the manufacturer's recommended layout and timing guidance to limit data-integrity and electromagnetic-interference issues. Typical uses include industrial Ethernet control equipment, embedded network gateways, data acquisition systems, print servers, and communication controllers. In each case, the device serves as the link between a host processor and a 10/100 Ethernet network. Its 3.3 V operation and commercial temperature range support compact systems where 100 Mbps connectivity is sufficient and a dedicated PHY is undesirable. Designers should confirm pin functions, timing, clocking, magnetics, and decoupling directly against the manufacturer datasheet before layout release. Particular attention should be given to MII clock timing, PHY termination, analog supply routing, and the separation between Ethernet traces and sensitive digital signals. These controls are more important than raw headline speed when establishing reliable network performance. This page organizes the LAN91C113-NS specifications, sourcing information, interface context, application guidance, and same-package replacement considerations. It also identifies which technical details require confirmation from the manufacturer documentation before a new PCB is released.

RFQ İletişim
LAN91C113-NU - 10/100 Ethernet MAC/PHY | Microchip
LAN91C113-NU

LAN91C113-NU - 10/100 Ethernet MAC/PHY | Microchip

The Microchip Technology LAN91C113-NU is a 16-bit 10/100 Base-T/TX Ethernet controller that combines a non-PCI Media Independent Interface MAC and integrated PHY in a 128-pin TQFP package measuring 14 x 14 mm. It operates from a 3.3 V supply and connects a host processor through the parallel MII interface. An Ethernet MAC, or Media Access Control, manages frame transmission, reception, addressing, and access to the physical network medium. A PHY implements the physical signaling layer between the MAC and a twisted-pair cable. The LAN91C113 integrates both functions into one controller, reducing board area and external PHY count compared with a separate MAC and Ethernet transceiver design. The controller supports 10Base-T and 100Base-TX operation over a 16-bit parallel MII. This combination suits embedded systems that already have a host processor with a compatible parallel bus but do not include an Ethernet PHY. Integration can reduce board routing, connector requirements, and the number of components requiring firmware and driver support. The LAN91C113-NU belongs to the Ethernet interface IC and network interface controller hierarchy. Unlike a PCI-based Ethernet card, the parallel MII architecture connects directly to processor logic rather than a host peripheral bus. The 3.3 V operating supply is compatible with modern embedded processor systems, although the complete design must also satisfy the voltage requirements of attached memory, magnetics, and physical-layer circuitry. Typical applications include industrial monitoring equipment, building automation controllers, embedded test equipment, industrial gateways, and compact network appliances. A typical implementation places the controller and an Ethernet jack with integrated magnetics on the same PCB, connects the host processor to the MII signals, and configures the MAC and PHY through the device’s control interface. Design should begin with the manufacturer’s reference schematic and signal-integrity guidance. Route the parallel MII clock and data signals as a controlled-length group, provide the required decoupling, and follow the recommended magnetics and impedance-termination layout. Confirm that the host processor’s MII timing, voltage levels, interrupt requirements, and software driver support match the controller before committing the PCB layout. This page consolidates the product identity, package information, application guidance, comparison criteria, and practical integration considerations engineers need when evaluating the LAN91C113-NU for a 10/100 Ethernet design. Use the Request a Quote form on this page for current commercial availability, packaging, lead time, and sourcing support.

RFQ İletişim
LAN91C93I-MC Full-Duplex Ethernet Controller | Microchip
LAN91C93I-MC

LAN91C93I-MC Full-Duplex Ethernet Controller | Microchip

Microchip Technology LAN91C93I-MC is a non-PCI single-chip full-duplex Ethernet controller with a 1.25 MB/s data rate, 10 Base-T PHY interface, CMOS process technology, and a 100-pin QFP package. It combines local-bus Ethernet controller functionality with independent transmit and receive operations for switched-Ethernet systems. An Ethernet controller is a semiconductor interface between a host processor and an Ethernet network. Within the product hierarchy, LAN91C93I-MC is an Ethernet controller, network interface controller, interface IC, and semiconductor. Its local-bus architecture avoids requiring a PCI bus while giving embedded processors direct access to Ethernet communication functions through a comparatively simple software interface. The controller supports full-duplex switched Ethernet and maintains independent transmit and receive operations. This architecture can improve effective communication concurrency compared with a controller that must coordinate both directions through one path. The 1.25 MB/s rated transfer rate and 10 Base-T PHY interface identify the LAN91C93I-MC as a 10 Mb/s-class embedded Ethernet solution rather than a Fast Ethernet or Gigabit Ethernet controller. According to the manufacturer datasheet, LAN91C93I is designed to be 100% software compatible with LAN91C92, LAN91C94, and LAN91C96 when operating in local-bus mode. This compatibility is particularly useful when preserving an established driver and application interface is more important than redesigning the entire network software stack. The integrated device also retains LAN91C92 functionality for local-bus environments. Typical applications include embedded industrial control, instrument networking, embedded appliance connectivity, point-of-sale equipment, and legacy embedded systems that require full-duplex switched Ethernet. The 100-QFP package exposes the controller's processor-side, memory-side, Ethernet, and power connections through a relatively high pin count suited to multilayer or through-hole-compatible board assembly. Designers should verify the complete pin description, voltage limits, clocking requirements, initialization sequence, and transceiver interface in the manufacturer datasheet before layout release. They should also confirm that the external magnetics, RJ-5 interface, isolation requirements, and system grounding topology suit the target network environment rather than assuming that the controller alone constitutes a complete Ethernet interface. This product overview combines the manufacturer interface description, package details, software-compatibility information, verified alternatives, and practical selection considerations. It also identifies where an engineer must consult the official datasheet for complete electrical limits and PCB implementation details.

RFQ İletişim
LAN91C93I-ME 10BASE-T Ethernet Controller | Microchip
LAN91C93I-ME

LAN91C93I-ME 10BASE-T Ethernet Controller | Microchip

The Microchip Technology LAN91C93I-ME is a non-PCI single-chip full-duplex Ethernet controller with an integrated 10BASE-T PHY interface, supplied in a 100-pin TQFP package. It is designed for local-bus systems and supports independent transmit and receive operations. The manufacturer identifies the LAN91C93I as 100% software-compatible with the LAN91C92, LAN91C94, and LAN91C96 in local-bus mode. An Ethernet controller is an interface IC that connects a processor or embedded host to an Ethernet physical layer. In this device, the controller and 10BASE-T PHY functions are integrated into one device. That integration reduces the number of external interface components required in an embedded Ethernet design while retaining a direct local-bus software interface. The Ethernet controller category belongs to the broader network-interface hierarchy: Ethernet controller → network interface IC → interface IC → semiconductor. The principal feature is support for full-duplex switched Ethernet with independent transmit and receive paths. Full-duplex operation allows each direction to be active simultaneously, which improves link utilization compared with a shared half-duplex arrangement. The integrated 10BASE-T interface also provides compatibility with 10 Mb/s Ethernet infrastructure. The -ME ordering code identifies the specific package and product configuration, while the -I family designation denotes the industrial-oriented LAN91C93I device family described by Microchip. The LAN91C93I architecture incorporates LAN91C92 local-bus functionality and extends it for switched full-duplex Ethernet. According to the manufacturer datasheet, independent transmit and receive operations allow the controller to manage both traffic directions concurrently. Existing local-bus software can also be reused because the LAN91C93I is stated to be 100% software-compatible with LAN91C92, LAN91C94, and LAN91C96 when operated in local-bus mode. Typical uses include embedded industrial controllers, local-bus embedded systems, legacy platform upgrades, and equipment that requires a dedicated 10BASE-T network interface without PCI. Its software continuity makes it especially relevant when an existing local-bus network stack must be retained while the physical network is converted to full-duplex switched Ethernet. Careful initialization, bus timing, and PHY integration remain essential during board bring-up. For a new design, first confirm that the host bus, address map, interrupt structure, and Ethernet driver expectations match the LAN91C93I register and software model. Review the manufacturer datasheet pin-description table and typical application circuit before assigning signals or laying out the 100-pin TQFP footprint. Also verify the selected magnetic-component and Ethernet-connector implementation against the required 10BASE-T topology. This product page combines the verified manufacturer overview, package information, software-compatibility relationships, application guidance, and practical selection criteria. It also distinguishes confirmed drop-in candidates from options that require board-level verification, helping engineers compare legacy Ethernet-controller options without treating software equivalence as automatic hardware equivalence.

RFQ İletişim
LAN91C93I-MS - 10Mbps Ethernet Controller | Microchip
LAN91C93I-MS

LAN91C93I-MS - 10Mbps Ethernet Controller | Microchip

The Microchip Technology LAN91C93I-MS is a single-chip, non-PCI Ethernet controller with a 10 Mbps IEEE 802.3 10BASE-T PHY interface, supplied in a 100-pin QFP package measuring 14 x 20 mm. It combines an Ethernet media-access controller with a local-bus interface and is designed for embedded systems that require compact, software-compatible Ethernet connectivity. The controller operates from 3.3 V or 5 V supply rails and is available in tray packaging as LAN91C93I-MS. An Ethernet controller is an interface IC that manages frame transmission and reception between a host processor and an Ethernet physical layer. In this product hierarchy, the LAN91C93I integrates an IEEE 802.3 Ethernet MAC, a 10BASE-T PHY interface, and a local-bus host interface. This integration reduces external component count compared with a design using a separate network controller and physical-layer transceiver, while preserving a conventional processor-facing software interface. Key features include a 10 Mbps data rate, support for full-duplex switched Ethernet, and independent transmit and receive operations. The LAN91C93I architecture incorporates the local-bus functionality associated with the LAN91C92 family. The manufacturer datasheet also states that the controller is 100% software compatible with the LAN91C92, LAN91C94, and LAN91C96 in local-bus mode, which can simplify firmware migration among supported controller generations. The controller uses a local-bus architecture rather than a PCI interface, making it appropriate for embedded processors and custom bus designs that do not expose PCI host connectivity. Its integrated 10BASE-T PHY interface connects the digital Ethernet controller to a compliant network physical layer. Support for full-duplex switched Ethernet permits simultaneous sending and receiving, unlike designs restricted to half-duplex shared-network operation. Typical uses include industrial monitoring equipment, embedded test systems, legacy factory controls, serial-to-Ethernet equipment, and compact data-acquisition platforms. In these systems, the local-bus interface connects the Ethernet controller to a host processor, while the 10BASE-T PHY interface connects the board to copper Ethernet. Designers should confirm the required host-bus timing, transceiver characteristics, and electrical isolation before integrating the controller into a new design. The principal design consideration is interface compatibility. LAN91C93I is intended to maintain software compatibility with selected LAN91C92, LAN91C94, and LAN91C96 devices in local-bus mode, but software compatibility alone does not guarantee unconditional PCB interchangeability. Confirm package dimensions, pin assignments, supply sequencing, clock requirements, and transceiver characteristics in the manufacturer datasheet before releasing a replacement or respin. This page organizes the controller’s key electrical, packaging, compatibility, application, and design information into an engineering-focused reference. It also distinguishes verified drop-in candidates from broader software-compatible family members, helping procurement and design teams assess replacements with the appropriate technical checks.

RFQ İletişim
LAN91C93I-MU - 10 Mbps Ethernet Controller | Microchip | TQFP-100
LAN91C93I-MU

LAN91C93I-MU - 10 Mbps Ethernet Controller | Microchip | TQFP-100

The Microchip Technology LAN91C93I-MU is a non-PCI, single-chip 10 Mbps Ethernet controller supporting IEEE 802.3 and a 10BASE-T PHY interface in a 100-pin TQFP package measuring 14 x 14 mm. It operates from a 3.3 V supply, with some catalog listings identifying compatibility with 3.3 V and 5 V systems. The controller provides integrated local-bus networking, full-duplex switched Ethernet operation, independent transmit and receive paths, and an enhanced transmit queue for efficient packet management. Its 100-TQFP footprint supports conventional surface-mount PCB assembly rather than a legacy PC/PCI bus interface. The LAN91C93I architecture combines local-area-network controller functionality with a simple software interface and retains compatibility with the LAN91C92, LAN91C94, and LAN91C96 in local-bus mode. These characteristics make the device suitable for embedded Ethernet equipment that requires deterministic network connectivity without requiring a PCI host interface. The LAN91C93I-MU is identified by Microchip as LAN91C93I with the -MU ordering suffix and is supplied in a green 100-pin QFP package. Designed for industrial-temperature operation, the device is specified from -40°C to +85°C. A typical design uses the controller with external magnetic isolation for the Ethernet physical layer, a 3.3 V supply, a local host processor connected through the device's parallel host bus, and an RJ45 network interface. The controller supports 10BASE-T rather than 100BASE-TX, so link speed and physical-layer requirements must be matched to legacy or cost-sensitive Ethernet equipment. Because the LAN91C93I is not a PCI Ethernet peripheral, host-bus timing, address mapping, interrupt connectivity, and software driver configuration are central PCB considerations. Its integrated architecture reduces the number of external networking components while preserving a conventional microcontroller or processor interface. An Ethernet controller is an interface integrated circuit that manages frame transmission, reception, buffering, addressing, and host communication for an Ethernet network. The LAN91C93I belongs to the local-bus controller hierarchy, combining an Ethernet MAC, protocol handling, and PHY-interface logic into one device. Its IEEE 802.3 and 10BASE-T support connect it to the Ethernet physical-layer ecosystem, while full-duplex switched Ethernet capability allows transmit and receive traffic to proceed independently. This integration places the LAN91C93I between a host processor and an Ethernet transceiver, simplifying the hardware architecture compared with a solution using a discrete network controller and additional interface glue. Key device characteristics include 10 Mbps Ethernet operation, a 10BASE-T PHY interface, full-duplex switched Ethernet support, independent transmit and receive operations, and an enhanced transmit queue. The controller's local-bus mode software compatibility with the LAN91C92, LAN91C94, and LAN91C96 can simplify firmware migration when an existing product family already uses those controllers. Its non-PCI architecture also provides an important alternative for embedded systems whose processors do not expose a conventional PCI bus. The 100-TQFP package provides enough pins for the parallel host interface, control signals, memory connections, and Ethernet-related signals, but it also requires careful escape routing and multilayer-board planning. The specified -40°C to +85°C operating range suits industrial equipment where commercial-temperature components would be insufficient. Technically, the LAN91C93I combines local-area-network controller functions with an enhanced transmit queue and fully independent receive and transmit operations. The enhanced queue allows the software driver to stage packets more effectively, which is valuable in systems where network traffic must be transferred between an external processor and the Ethernet medium without blocking host execution. The PHY interface follows 10BASE-T requirements rather than 100BASE-TX, determining the external magnetics, connector, line-driver, and cable requirements of the board. Local-bus software compatibility with four related controller families reduces the amount of low-level networking code that must be rewritten, although drivers should still be checked for register, interrupt, and device-option differences. The device is manufactured in CMOS technology and is specified as a green package, supporting lead-free assembly processes where its production documentation confirms the appropriate soldering profile. Typical applications include industrial control terminals, embedded instrumentation, legacy network gateways, factory-floor controllers, and compact embedded networking modules. In each case, the controller provides a conventional Ethernet interface to a host processor while managing frames, transmit queuing, and receive activity in hardware. A 10BASE-T-only design is appropriate for legacy infrastructure, isolated point-to-point links, or equipment where 10 Mbps is sufficient and component cost matters. It may also serve as a migration interface when an established product already contains LAN91C92-, LAN91C94-, or LAN91C96-compatible software. Modern high-bandwidth gateways generally require a faster Ethernet controller, but the LAN91C93I remains useful where software continuity and local-bus integration outweigh throughput. The primary PCB design consideration is the parallel host-bus and memory-interface routing required by a 100-pin TQFP. Place decoupling capacitors close to each applicable supply pin, maintain short high-speed Ethernet paths between the controller, external PHY components, magnetics, and RJ45 connector, and provide solid ground-plane continuity under the device. Keep analog and digital return currents separated where the board stackup permits, and follow the manufacturer's recommended pinout and reference circuitry. Verify the external network interface against the 10BASE-T design requirements rather than assuming that a 100BASE-T magnetics assembly is interchangeable. This page combines manufacturer and distributor product facts with package, application, purchasing, and replacement guidance to support early design decisions. It distinguishes verified electrical and package characteristics from parameters that require confirmation in the complete manufacturer datasheet, helping engineers qualify the LAN91C93I-MU for embedded Ethernet designs before committing to a PCB layout or production release.

RFQ İletişim
LAN91C96-MS - 10/100 Ethernet Controller | Microchip
LAN91C96-MS

LAN91C96-MS - 10/100 Ethernet Controller | Microchip

The Microchip Technology LAN91C96-MS is a single-chip 10/100 Ethernet controller with a 3.3 V supply, a 100-pin QFP package measuring 14 x 20 mm, and an operating temperature range of -40 °C to 85 °C. It integrates an Ethernet MAC, physical-layer encoding and decoding functions, packet RAM, and host-bus connectivity, reducing the component count required for embedded Ethernet designs. An Ethernet controller is an interface IC that connects an embedded host processor to a physical Ethernet network. Within the product hierarchy, the LAN91C96-MS is an Ethernet MAC and physical-layer controller, which is part of a communications interface IC and ultimately a semiconductor. It supports non-PCI systems using Local Bus, PCMCIA, or Motorola 68000 bus interfaces instead of requiring a PCI-compatible host. Key features include full-duplex switched Ethernet support, enhanced transmit queue management, integrated packet RAM, and support for AUI and twisted-pair network connections. The supplied manufacturer information identifies the LAN91C96 family as integrating most IEEE 802.3 functionality, including MAC protocol handling, physical-layer encoding and decoding, twisted-pair transceiver functions, and link-integrity testing. The controller addresses legacy embedded platforms that need Ethernet connectivity without a PCI bus. Its local-bus addressing uses A0-A9 and A15 together with active-low nREG, nCE1, nWE, and nOE signals. Word reads from odd byte addresses can return a zero value in the upper byte because that byte is a don't-care under the referenced PCMCIA attribute-memory access rule. Typical uses include legacy embedded systems, industrial controllers, compact network adapters, PC Card LAN equipment, and custom communication equipment requiring a non-PCI Ethernet interface. The manufacturer also identifies the low-profile TQFP option as suitable for mobile applications such as PC Card LAN adapters, although the verified LAN91C96-MS ordering information identifies a 100-pin QFP package. Designers should verify the exact PCB footprint, clock source, bus timing, transceiver connections, and power requirements against the manufacturer datasheet before substituting this legacy controller. The -40 °C to 85 °C specification supports industrial-temperature designs, but applications needing a wider commercial range should select a variant with the appropriate documented rating. This page consolidates verified distributor identification, manufacturer product information, datasheet details, interface features, and package data. It also separates documented facts from unresolved parameters and avoids presenting unspecified pricing, pin names, and competitor compatibility as confirmed engineering data.

RFQ İletişim
LAN91C96-MU - 10Mbps Ethernet Controller | Microchip Technology
LAN91C96-MU

LAN91C96-MU - 10Mbps Ethernet Controller | Microchip Technology

Microchip Technology LAN91C96-MU is a single-chip 10Mbps Ethernet controller with a 10BASE-T PHY, parallel host interface, MAC functions, and integrated packet RAM in a 100-pin TQFP package measuring 14 x 14 mm. The device supports 3.3 V and 5 V operation and combines Local Bus, PCMCIA, and Motorola 68000 bus interfaces in one CMOS Ethernet controller. Its integrated architecture reduces the external component count required for embedded Ethernet connectivity while providing full-duplex switched Ethernet support, enhanced transmit queue management, and 6 kB of packet RAM. An Ethernet controller is an interface IC that connects a host processor or embedded system to an Ethernet physical network. The LAN91C96 family integrates the Media Access Control layer, physical-layer interface, packet buffer, and host-bus logic. This places it in the hierarchy Ethernet controller > network interface controller > interface IC > semiconductor, making it suitable for legacy industrial, embedded, and PCMCIA equipment that cannot rely on a modern PCI Ethernet controller. The LAN91C96-MU supports 10Mbps Ethernet operation and a parallel 10BASE-T PHY interface. According to Microchip product information, the controller integrates all MAC and physical-layer functions and the packet RAM required to implement a complete Ethernet node. The datasheet also identifies support for full-duplex switched Ethernet and enhanced transmit queue management. These features are useful where the host bus architecture, rather than network throughput, is the primary system constraint. The device uses a 100-TQFP surface-mount package and supports both 3.3 V and 5 V supply conditions, allowing integration with systems using either voltage domain. Its Local Bus, PCMCIA, and Motorola 68000 interfaces provide design flexibility across embedded processor and legacy computer platforms. The manufacturer datasheet states that the LAN91C96 is pin and software compatible with the LAN91C92 and LAN91C94 in Local Bus mode, which supports incremental upgrades of qualifying legacy designs. Typical applications include embedded industrial controllers, PCMCIA Ethernet adapters, legacy Local Bus systems, Motorola 68000-based equipment, and custom network interface cards. The integrated 6 kB packet RAM can reduce host-memory traffic and buffer network packets, while full-duplex operation supports switched-network installations. Designers should verify that the host timing, transceiver connection, connector magnetics, and software driver are supported by the target system architecture. The primary design consideration is voltage and signal compatibility with the existing bus. Because the controller integrates Ethernet functions but requires an appropriate external network interface implementation, designers must follow the manufacturer reference circuitry for magnetics, termination, clocking, and decoupling. Firmware and bus-driver compatibility are equally important; an identical package does not by itself guarantee that a replacement can operate correctly in every legacy operating environment. This product data combines manufacturer documentation, distributor package information, sourcing details, and verified same-family alternatives. It also adds practical guidance for comparing the LAN91C96-MU with other LAN91C96 package and temperature designations without presenting package-only changes as separate functional technologies.

RFQ İletişim
LAN91C96I-MS - 10Mbps Full-Duplex Ethernet Controller | Microchip
LAN91C96I-MS

LAN91C96I-MS - 10Mbps Full-Duplex Ethernet Controller | Microchip

The Microchip Technology LAN91C96I-MS is a non-PCI single-chip Ethernet controller with a 10 Mbps 10BASE-T PHY, parallel host interface, integrated packet RAM, and 100-pin QFP package. It supports full-duplex switched Ethernet, independent transmit and receive operations, Magic Packet wake-up, optical-fiber support, programmable LED indication, and a low-power mode. The device operates from 3.3 V and is specified for industrial temperatures from -40°C to +85°C. An Ethernet controller is a network interface semiconductor that connects an embedded host bus to physical-layer hardware. This device integrates MAC functions, the 10BASE-T physical layer, and packet RAM on one VLSI chip. It combines Local Bus, PCMCIA, and Motorola 68000 bus interfaces, allowing it to serve legacy embedded systems, embedded controllers, industrial equipment, and network-interface subsystems without requiring a separate Ethernet PHY. The LAN91C96I-MS supports full-duplex switched Ethernet at 10 Mbps and provides independent transmit and receive operations. Its enhanced transmit queue helps the host organize frames for serial transmission, while packet RAM reduces the amount of external buffering required. Additional network functions include Magic Packet, programmable LED indication, support for optical-fiber links, and a low-power operating mode for power-sensitive embedded designs. The parallel interface connects the controller to a host processor through a structured register and buffer architecture. Local Bus compatibility is important because the Microchip LAN91C96i family is designed to be 100% pin and software compatible with the LAN91C92 and LAN91C94 when operating in Local Bus mode. This compatibility can simplify firmware maintenance when moving between qualified LAN91C-family controller designs without changing the established host-side software model. Typical uses include embedded data acquisition, legacy industrial controllers, print systems, point-of-sale terminals, embedded gateways, and equipment requiring a 10BASE-T network node. The integrated PHY simplifies the board-level network section, while the parallel host interface suits processors that do not include a dedicated Ethernet media-access controller. The 100-pin QFP package also provides ample signal access for host-bus, memory, clock, interrupt, and network connectivity. Designers should account for all power, ground, clock, reset, interrupt, transmit, and receive connections in the manufacturer pin-description table. PCB placement should keep the 10BASE-T network section away from high-speed or high-current switching circuitry, while providing a low-impedance return path for the interface and supply pins. Software configuration should use the documented register definitions and account for the controller's independent transmit and receive operation. This product page combines the manufacturer architecture description, distributor package information, compatibility information, and practical selection guidance. It also identifies same-package family alternatives and explains where package, temperature, or ordering-option differences require engineering review before a replacement is approved.

RFQ İletişim
LAN91C96I-MU - 10Mbps Ethernet Controller | Microchip
LAN91C96I-MU

LAN91C96I-MU - 10Mbps Ethernet Controller | Microchip

Microchip Technology LAN91C96I-MU is a non-PCI, single-chip full-duplex Ethernet controller with a 10 Mbps 10BASE-T interface, 3.3 V/5 V operation, and a 100-pin TQFP package measuring 14 mm by 14 mm. The controller combines Ethernet MAC and physical-layer functions with packet RAM in one VLSI device for embedded Local Bus, PCMCIA, and Motorola 68000 systems. An Ethernet controller is an interface IC that manages frame transmission, reception, addressing, and the connection between a host bus and physical network medium. The LAN91C96 belongs to the Ethernet controller hierarchy, where a MAC processes frames and an integrated PHY provides the physical-layer interface. Integrating the MAC, PHY, and packet memory reduces external component count while supporting a 10BASE-T network node. Key features include full-duplex switched Ethernet support, independent transmit and receive operations, Magic Packet wake-up, and an enhanced transmit queue. The manufacturer identifies the LAN91C96i family as 100% pin- and software-compatible with the LAN91C92 and LAN91C94 when operating in Local Bus mode. This compatibility makes the LAN91C96I-MU especially relevant to legacy embedded-platform upgrades that must preserve an existing 100-pin TQFP footprint and Local Bus software model. The controller integrates the MAC, physical layer, and packet RAM rather than requiring a separate network coprocessor, PHY, or external packet buffer. Its independent transmit and receive paths support simultaneous traffic handling, while the enhanced transmit queue helps organize frames awaiting transmission. Local Bus operation provides a direct path between the controller and compatible embedded processors without requiring the PCI bus protocol used by many later Ethernet controllers. Typical uses include industrial embedded control systems, legacy instrument controllers, printer and terminal equipment, embedded network appliances, and legacy PCMCIA systems. The 10BASE-T interface is appropriate for established 10 Mbps twisted-pair networks where interoperability with installed infrastructure and software is more important than support for Fast Ethernet or Gigabit Ethernet. Designers should confirm the processor voltage, Local Bus signals, transceiver connections, isolation requirements, and software-driver expectations before integration. The 100-pin TQFP footprint makes replacement mechanically straightforward, but pin and software compatibility do not eliminate the need to verify operating conditions, timing, termination, and application-specific network requirements. This page combines the manufacturer's product information, interface characteristics, family compatibility, practical implementation guidance, drop-in alternatives, and application-specific engineering context. It is intended to help designers identify whether the LAN91C96I-MU satisfies the required Ethernet speed, bus architecture, package, voltage, and legacy-platform constraints.

RFQ İletişim
LAN91C96QFP - 10Mbps Ethernet Controller | Microchip Technology
LAN91C96QFP

LAN91C96QFP - 10Mbps Ethernet Controller | Microchip Technology

The Microchip Technology LAN91C96QFP is a non-PCI single-chip full-duplex Ethernet controller supporting 10Mbps Ethernet and 10BASE-T operation. It combines an Ethernet MAC, physical-layer functions, packet RAM, and host-bus connectivity in a 100-pin QFP package measuring 20 mm by 14 mm. The device also supports Magic Packet functionality for remote wake-up. An Ethernet controller is a network interface semiconductor that manages frame transmission, reception, addressing, and the host-side data path between a processor and an Ethernet network. Within the product hierarchy, the LAN91C96 is an Ethernet MAC controller, an interface IC, a communications semiconductor, and a surface-mount integrated circuit. Its non-PCI architecture allows it to connect through processor-specific bus interfaces rather than requiring a PCI peripheral bus. The principal identified features are a 10Mbps data rate, 10BASE-T twisted-pair operation, full-duplex operation, integrated MAC and physical-layer functions, and embedded packet RAM. The controller supports Local Bus, PCMCIA, and Motorola 68000 bus interfaces according to the manufacturer documentation. Magic Packet capability provides a conventional mechanism for waking a remote system through a specially formatted network frame. The integrated architecture reduces the number of discrete devices required to implement a 10BASE-T network node. MAC processing, physical-layer functionality, and packet buffering are consolidated into one controller, while the host processor communicates through the supported local interfaces. This integration is particularly useful in legacy embedded systems designed around non-PCI buses rather than modern PCI Express networking devices. Typical applications include embedded control systems, industrial equipment, legacy communication appliances, and compact network-access products requiring a 10Mbps Ethernet node. The device can also support remote system management through Magic Packet wake-up when the host platform retains enough power to monitor and reactivate its Ethernet interface. PCB implementation requires careful assignment of the 100-pin package, power distribution, clocking, reset, memory, and network-magnetics connections according to the manufacturer datasheet. Because this part is an older Ethernet controller, its voltage, timing, temperature, and transceiver-interface limits should be checked against the exact system requirements before design release. This page organizes the confirmed controller capabilities, package information, sourcing paths, replacement constraints, and engineering considerations into a concise design reference. It also distinguishes true pin-compatible substitutions from related family members so legacy-system maintenance can proceed without an unsupported footprint assumption.

RFQ İletişim
LAN9210-ABZJ - 10/100 Ethernet Controller | Microchip Technology
LAN9210-ABZJ

LAN9210-ABZJ - 10/100 Ethernet Controller | Microchip Technology

The Microchip Technology LAN9210-ABZJ is a single-chip 10/100 Ethernet controller with an integrated MAC and PHY, a parallel host interface, and a 56-QFN 8 x 8 mm package. It supports IEEE 802.3 10BASE-T and IEEE 802.3u 100BASE-TX, HP Auto-MDIX, a 16-bit external data bus, a 7-bit address bus, and data rates up to 12.5 Mbps. An Ethernet controller is a semiconductor that connects an embedded processor or microcontroller to a physical Ethernet network. It combines packet processing, host-bus access, and physical-layer signaling into one device, reducing the number of discrete components required for an embedded Ethernet port. Within the product hierarchy, the LAN9210 is a 10/100 Ethernet controller, an Ethernet interface IC, and a network-connected embedded interface device. The controller includes large transmit and receive FIFOs for applications experiencing network latency or burst traffic. Its SRAM-like slave interface provides a direct connection to common 16-bit microprocessors and microcontrollers, as well as 32-bit processors that expose a 16-bit external bus. The integrated Checksum Offload Engine automatically handles protocol checksum tasks, reducing host processor overhead during Ethernet packet processing. HP Auto-MDIX allows the device to support connection polarity and crossover handling automatically. This simplifies cabling in embedded systems because the design does not require separate fixed MDI and MDI-X routing. The LAN9210-ABZJ operates from a 1.7 V to 1.9 V CMOS supply and supports parallel 16-bit data and 7-bit addressing, making it suitable for embedded platforms that cannot accommodate a high-speed serial Ethernet host interface. Typical uses include industrial control equipment, factory automation controllers, embedded gateways, network management appliances, test equipment, and compact data-acquisition systems. The integrated MAC/PHY arrangement is especially useful where board space is limited but a reliable 10/100BASE-TX connection is required. A suitable processor must provide compatible bus timing, chip-select logic, and sufficient interrupt handling for Ethernet traffic. When laying out the PCB, follow the manufacturer’s recommended QFN land pattern and thermal-pad via arrangement. The 56-QFN package includes an exposed VSS pad, so electrical and thermal grounding depend on correct pad connection and via placement. Validate signal integrity, supply decoupling, isolation requirements, and connector magnetics against the final board-level design. This page consolidates the key Ethernet features, sourcing guidance, package constraints, and practical design considerations engineers need when integrating the LAN9210-ABZJ into embedded networking equipment. Use the manufacturer datasheet for the complete register map, electrical limits, timing diagrams, and authoritative pin descriptions.

RFQ İletişim
LAN9211-ABZJ - 10/100 Ethernet Controller | Microchip Technology
LAN9211-ABZJ

LAN9211-ABZJ - 10/100 Ethernet Controller | Microchip Technology

The Microchip Technology LAN9211-ABZJ is a single-chip 10/100 Base-T Ethernet controller with a parallel host interface, HP Auto-MDIX support, and industrial-temperature capability. The device supports operation from 2.97 V to 3.63 V, operates at 10 Mbit/s or 100 Mbit/s, and is packaged in a 56-pin QFN measuring 8 mm by 8 mm. An Ethernet controller is an interface integrated circuit that connects an embedded host processor to a physical Ethernet network. It combines protocol processing, media access control, and physical-layer signaling into one device. The LAN9211 belongs to the hierarchy of Ethernet controller, network interface controller, interface IC, and semiconductor, reducing the component count and PCB area required for an embedded Ethernet port. The LAN9211-ABZJ provides a 16-bit parallel interface to its host system and integrates a 10/100 Ethernet PHY. HP Auto-MDIX supports automatic handling of straight-through and crossover cable connections, allowing a single RJ45 design to work with common Ethernet cabling arrangements. Its single-chip implementation is intended for embedded applications requiring compact networking with controlled system cost. The manufacturer describes the LAN9211 as a full-featured controller designed for applications where performance, flexibility, ease of integration, and system cost control are important. Its parallel host interface is suitable for processors able to transfer network data through a memory-mapped bus. Firmware and host-driver configuration remain important elements of the integration because interrupt, descriptor, and buffer-management behavior determine practical network throughput. Typical uses include industrial Ethernet equipment, embedded control systems, communications appliances, test instruments, and networked sensors. The 10/100 Mbit/s rate is appropriate for management traffic, serial-to-Ethernet equipment, factory monitoring, and legacy industrial networks. HP Auto-MDIX simplifies field installation by reducing cabling restrictions at the connector. The 56-pin QFN package makes high-density routing possible but requires careful thermal and layout work. Place the exposed ground pad on a multilayer board with a via array and provide the decoupling network shown in the manufacturer datasheet. The package suffix ABZJ identifies the ordered tray configuration, and the QFN land pattern must be designed before assembly. This product page consolidates the exact orderable MPN, core interface and packaging details, manufacturer documentation, sourcing guidance, and design cautions. It also distinguishes documented order information from replacement analysis so engineers can evaluate PCB reuse without assuming that a related Ethernet controller has identical pinout, host timing, or electrical behavior.

RFQ İletişim
LAN9215-MT - 100Mbps Ethernet Controller | Microchip
LAN9215-MT

LAN9215-MT - 100Mbps Ethernet Controller | Microchip

The Microchip LAN9215-MT is a single-chip 10/100 Ethernet controller with a 100 Mbps data rate, a 16-bit parallel MII interface, and a 100-pin TQFP package measuring 14 x 14 mm. It integrates an Ethernet media-access controller, PHY, and connectivity needed for embedded network equipment. The verified distributor listing identifies it as a 10/100 Base-T/TX PHY controller using a parallel interface, while the manufacturer describes it as a flexible embedded Ethernet solution. An Ethernet controller such as the LAN9215-MT connects an embedded host interface to a physical copper network. Within the hierarchy of integrated circuits, it is an Ethernet interface controller and a networking semiconductor. Its 100 Mbps throughput targets Fast Ethernet networks, while its 16-bit MII provides a parallel connection to a host processor. Integrating the controller and PHY reduces external network-interface component count compared with a discrete MAC-and-PHY design. Verified features include support for 10 Mbps and 100 Mbps operation, HP Auto-MDIX support, driver compatibility with the preceding LAN9118 family, and footprint, register, and driver compatibility with those devices. The manufacturer datasheet states a 2.97 V to 3.63 V supply range and a maximum clock frequency of 25 MHz. A separate component listing describes a 3.3 V device and an operating range from 0°C to +70°C, consistent with the -MT commercial-temperature ordering option. The LAN9215-MT is suitable for embedded Ethernet systems that require a CPU-facing parallel interface rather than a serial SPI host interface. Typical uses include industrial controllers, embedded gateways, test equipment, communications modules, and OEM data-acquisition products. Its 16-bit host interface is particularly appropriate for microprocessors and programmable logic devices able to sustain parallel bus transactions at Ethernet timing requirements. The primary integration consideration is the Ethernet magnetics and analog network path. The manufacturer datasheet notes that supporting HP Auto-MDIX can require different magnetics and passive components plus a minor PCB change. Designers should therefore follow the manufacturer reference schematic and preserve the required layout, power, decoupling, and magnetics implementation rather than treating the controller as a standalone digital component. This page consolidates verified manufacturer and distributor information, practical integration guidance, application fit, and transparent gaps where complete electrical or pin-level data was not provided. The official LAN9215 product page and datasheet remain the controlling references for registers, timing, electrical limits, and reference design implementation as verified on 2026-10-22.

RFQ İletişim