Ürünler (44.000+)

MAX3490ESA+T - 10Mbps Full-Duplex RS-485/422 | Analog Devices
MAX3490ESA+T

MAX3490ESA+T - 10Mbps Full-Duplex RS-485/422 | Analog Devices

The Analog Devices MAX3490ESA+T is a 3.3V-powered, low-power RS-485/RS-422 transceiver with one driver and one receiver in an 8-pin SOIC package. It supports data rates up to 10Mbps, operates from 3V to 3.6V, and is designed for full-duplex industrial communications. The tape-and-reel ordering code identifies the lead-free MAX3490ESA variant supplied on carrier tape. An RS-485/RS-422 transceiver is an interface IC that converts between single-ended logic-level signals and differential bus signals. Differential signaling reduces susceptibility to common-mode noise and allows reliable data transfer over longer cables. In the broader hierarchy, the MAX3490 belongs to the RS-485/RS-422 transceiver family within interface ICs and wired-communication semiconductors. Key features include a 10Mbps maximum data rate, 3V to 3.6V supply operation, full-duplex communication, and an integrated driver and receiver. The manufacturer describes the MAX3483, MAX3485, MAX3486, MAX3488, MAX3490, and MAX3491 as 3.3V low-power transceivers for RS-485 and RS-422 communication. These devices support industrial-control, instrumentation, data-acquisition, and factory-automation links where robust differential signaling is required. The MAX3490 provides separate transmit and receive paths for full-duplex operation, allowing the transmitter and receiver to remain active simultaneously. Its 8-SOIC surface-mount package supports compact PCB layouts, while the 3.3V supply simplifies interfacing with modern microcontrollers, field-programmable gate arrays, sensors, and industrial controllers. The exact receiver enable, driver enable, and bus-failover behavior should be confirmed against the manufacturer datasheet for the specific ordering variant before schematic sign-off. Typical applications include full-duplex RS-485 links between industrial controllers and remote I/O modules, point-to-point RS-422 interconnects in test equipment, factory-floor sensor networks, and embedded control systems. Compared with half-duplex transceivers that multiplex the driver and receiver onto the same bus pins, a full-duplex implementation can simplify timing and remove the need for software-managed bus turnaround. Designers should account for bus termination, fail-safe biasing, cable length, and grounding when using the MAX3490ESA+T. Differential buses normally require termination resistors at both ends of the cable, while bias resistors may be required to keep the bus in a defined state when no driver is active. Decoupling capacitors should be placed close to the supply and ground pins, and unused inputs should not be left floating. This page consolidates manufacturer product information, distributor pricing references, verified substitute candidates, pin-level guidance, and practical RS-485 design notes into one engineering-oriented resource. It also identifies which same-package alternatives are documented as pin-compatible replacements and where additional manufacturer verification is required.

RFQ İletişim
MAX349EAP+ - 8:1 Low-Voltage Multiplexer | Analog Devices
MAX349EAP+

MAX349EAP+ - 8:1 Low-Voltage Multiplexer | Analog Devices

Analog Devices MAX349EAP+ is a serially controlled, low-voltage 8-channel analog multiplexer with a maximum on-resistance of 100 ohms, supplied in a 20-pin SSOP package. It accepts single-supply operation from 2.7 V to 16 V or dual-supply operation from ±2.7 V to ±8 V. The matched on-resistance is limited to 16 ohms, with variation of no more than 10 ohms across the specified signal range. An analog multiplexer is an interface switch that connects one of several input or output channels to a common terminal. The MAX349 belongs to the hierarchy of analog switches, multiplexers, interface ICs, and semiconductors. Its eight channels can be selected through a serial control interface, reducing the number of GPIO pins required when a controller must route multiple analog signals through a shared circuit. The MAX349's maximum on-resistance of 100 ohms minimizes signal attenuation when it routes low-frequency analog signals. On-resistance matching between switches is specified at 16 ohms maximum, while flatness is limited to 10 ohms over the signal range. This matching helps preserve consistent signal behavior as the selected channel changes. The device also supports operation in either signal direction, allowing it to function as either a multiplexer or a demultiplexer. The MAX349 family is intended for low-voltage equipment where analog channels must be routed through a limited number of printed-circuit-board traces. Digital control reduces routing complexity, while dual-supply support permits bipolar signal handling when paired with negative and positive rails. A single 2.7 V to 16 V supply supports lower-voltage designs where a negative rail is unnecessary. Typical uses include multiplexed data acquisition, automated test equipment, industrial measurement systems, and portable instruments. An eight-channel arrangement is useful when several sensors, divider outputs, or control signals share a common converter input. The serial interface is particularly helpful in compact systems where conserving microcontroller or processor I/O is important. Designers should verify signal amplitude, supply configuration, serial-interface timing, and switch behavior before assigning channels. Keep routed analog signals within the device's specified operating range, account for the 100-ohm maximum on-resistance when calculating divider ratios, and use the manufacturer's pin-description table when making PCB connections. The MAX349 and MAX350 are related dual-supply multiplexer families, but they should not be treated as interchangeable without verifying channel count and pinout. This product page combines the official device identity, electrical characteristics, package information, application guidance, and practical replacement considerations. It also distinguishes the MAX349 from the MAX350 and explains when a verified drop-in substitute is preferable to redesigning around a different multiplexer architecture.

RFQ İletişim
MAX349EPN+ - 8:1 Low-Voltage MUX | Analog Devices
MAX349EPN+

MAX349EPN+ - 8:1 Low-Voltage MUX | Analog Devices

Analog Devices MAX349EPN+ is a serially controlled, low-voltage 8-channel multiplexer with a maximum on-resistance of 100 ohm, packaged in an 18-pin DIP. It supports dual 4-channel multiplexing, bidirectional signal conduction, break-before-make switching, and a fail-safe disconnect function. Its operating temperature range is -40°C to +85°C, while the stated supply-voltage limits cover +2.7 V to +16 V and -8 V to -2.7 V. An analog multiplexer is an interface IC that connects multiple signal paths to a shared output through digitally controlled switches. The MAX349 belongs to the analog-switch and multiplexer hierarchy within interface semiconductors. By selecting one of eight input channels for a common terminal, it reduces the number of signal lines and external routing required in data-acquisition, measurement, and control systems. The dual 4-channel architecture supports differential-style routing while retaining an 8:1 multiplexing mode. Key characteristics include a maximum on-resistance of 100 ohm, 300 ns and 400 ns stated switching-time figures, 8 pF channel capacitance, and 100 pA off leakage. The MAX349EPN+ is specified for both positive and negative supply rails. Positive operation extends from +2.7 V to +16 V, while negative operation extends from -8 V to -2.7 V. Its bidirectional analog channels allow signals to pass in either direction, making the device suitable for routed analog buses rather than only one-way output selection. The serially controlled interface reduces the number of control traces required compared with a conventional parallel-address multiplexer. Its 18-PDIP package has a stated 7.62 mm body width and is compatible with through-hole assembly. Because each selected channel contributes resistance and capacitance, the device is best suited to low- and moderate-frequency analog signals where switching time and on-resistance are compatible with the measurement bandwidth. The MAX349EPN+ also specifies break-before-make operation and fail-safe disconnect behavior for controlled signal routing. Typical uses include multiplexed sensor acquisition, laboratory measurement interfaces, industrial control signal routing, communication-channel selection, and compact test systems that must route several analog inputs through a shared conversion or processing chain. The -40°C to +85°C range supports industrial-temperature equipment, while the lead-free-compatible DIP format suits through-hole prototypes and legacy-style controller boards. Designers should account for the 100 ohm maximum channel resistance, 8 pF capacitance, and stated switching times when setting source impedance, bandwidth, settling time, and gain expectations. Confirm signal amplitudes against the positive or negative supply rails, and use the manufacturer pin-description table when assigning PCB nets and connector routing. This page combines the MAX349EPN+ operating limits, package details, verified drop-in comparison, application guidance, and PCB-focused design notes to support component selection and implementation. It also distinguishes the electrically similar MAX349CPN+ temperature option from a true cross-brand replacement.

RFQ İletişim
MAX350CWN+ - Dual 4:1 Multiplexer, 100 ohm | Analog Devices
MAX350CWN+

MAX350CWN+ - Dual 4:1 Multiplexer, 100 ohm | Analog Devices

The Analog Devices MAX350CWN+ is a serially controlled, low-voltage dual 4:1 analog multiplexer with two independent 4:1 switch sections in an 18-pin wide SOIC package. Its maximum on-resistance is 100 ohm, with on-resistance matching between switches specified to 16 ohm maximum and flatness specified to 10 ohm maximum over the operating signal range. The device supports bidirectional signal conduction. A multiplexer is a semiconductor switch that connects one of several inputs to a common output. The 4:1 architecture reduces the number of physical signal connections required in instrumentation, test, measurement, and data-acquisition systems. The MAX350 family combines eight switched signal paths into two serial-controlled 4:1 groups, making it useful when a system must route several low-voltage analog signals while keeping board wiring and control logic compact. The MAX350CWN+ uses serial control to select the active input path. According to the Analog Devices MAX350 product page, the MAX349 and MAX350 multiplexers conduct equally well in either direction and use CMOS implementations. Their specified dual-supply operating range extends from ±2.7 V to ±8 V. The MAX350CWN+ is identified by the distributor listings as a two-circuit, 4:1, 100 ohm device in an 18-SOIC package. On-resistance matching is particularly important when several channels carry similar or low-level analog signals. A matched network reduces channel-dependent gain and attenuation errors introduced by the multiplexer. The specified 100 ohm maximum on-resistance also indicates that the device is intended for low-voltage signal-routing applications where substantially lower resistance is generally not required. Typical uses include automated test equipment, data-acquisition systems, instrumentation, signal routing, and industrial control modules. In these systems, the MAX350CWN+ can present one selected signal to a measurement or conversion channel while a microcontroller or test controller operates the serial interface. The dual 4:1 organization allows two multiplexed groups to support paired, differential, or otherwise related signal paths. PCB implementation requires careful placement of the interface and routed signal nets to limit coupling, crosstalk, and impedance discontinuities. Keep serial-control traces away from sensitive analog paths, use a continuous ground reference, and observe the manufacturer's recommended bypass-capacitor and layout practices. Confirm supply sequencing, logic levels, input-voltage limits, and the exact 18-pin pinout against the manufacturer datasheet before fabrication. This product record combines the manufacturer product description with distributor package and channel information, then adds practical routing, matching, and selection guidance. It also identifies genuine same-family drop-in candidates while clearly separating verified facts from parameters that require confirmation from the manufacturer datasheet.

RFQ İletişim
MAX350EWN+ - Dual 4:1 Serial Multiplexer | Analog Devices
MAX350EWN+

MAX350EWN+ - Dual 4:1 Serial Multiplexer | Analog Devices

The Analog Devices MAX350EWN+ is a serially controlled, low-voltage CMOS analog multiplexer configured as two independent 4:1 switches in an 18-pin wide SOIC package. It operates from 2.7 V to 16 V and provides a maximum on-resistance of 100 ohm, with channel-to-channel matching limited to 16 ohm and resistance variation across the specified signal range limited to 10 ohm. The MAX350EWN+ conducts signal equally well in either direction, allowing it to route analog inputs or outputs through a serial interface. An analog multiplexer is a semiconductor that connects one signal path to one of several channels through controlled switches. The MAX350 family extends this category to the hierarchy of analog switch, multiplexer, routing IC, and signal-management semiconductor. Its 4:1 dual configuration provides two separately selectable channel groups, making it suitable for channel-scanning systems where multiple sensors, measurement inputs, or controlled outputs share a common signal chain. Key features include serial control, bidirectional signal conduction, low-voltage CMOS operation, and tightly matched switch resistance. The 100 ohm maximum on-resistance limits signal attenuation, while the 16 ohm maximum channel-to-channel match improves consistency when comparing readings across different channels. Its 18-pin wide SOIC package also provides a practical surface-mount footprint for industrial and instrumentation designs. The device uses a serial interface to select channels and control the multiplexers, reducing the number of package pins needed compared with a parallel-control multiplexer. This architecture is valuable in systems that route several slow or moderate-bandwidth analog signals, particularly when the microcontroller has limited general-purpose input/output capacity. Typical applications include multimeter and laboratory input switching, automated test equipment, data-acquisition modules, sensor-channel multiplexing, and control of multiple analog signal paths. The MAX350EWN+ is appropriate when bidirectional analog routing and matched resistance are more important than ultra-low on-resistance or high-speed video multiplexing. When laying out the circuit, keep analog traces short and connect the device to a stable low-noise supply. Confirm the serial interface levels and logic thresholds against the system controller, and verify that every switched signal remains within the specified analog input range. Check the full on-resistance and off-isolation characteristics in the manufacturer datasheet when the signal source is high impedance.

RFQ İletişim
MAX35103EHJ+ Reduced-Power ToF Converter | Analog Devices
MAX35103EHJ+

MAX35103EHJ+ Reduced-Power ToF Converter | Analog Devices

The Analog Devices MAX35103EHJ+ is a reduced-power time-to-digital converter with an integrated analog front end, real-time clock, and flash memory, specified for a 2.3 V to 3.6 V supply in a 32-pin TQFP (5 mm × 5 mm) package. It targets ultrasonic heat, water, and gas meters and increases the maximum time-of-flight measurement frequency in event timing mode from 2 Hz on the MAX35101 to 16 Hz. A time-to-digital converter, or ToF converter, measures the elapsed time represented by an ultrasonic pulse by converting a timing event into a digital result. The MAX35103 integrates the pulse-generation, receive-signal conditioning, timing, clock, and nonvolatile-measurement functions required by a compact ultrasonic metering front end. This integration reduces external circuitry compared with a discrete timer and analog receive chain while preserving a path to low-cost, low-power meter designs. According to the manufacturer datasheet, the MAX35103 consumes about half the average power of the MAX35101. The supplied sources do not provide a numeric average-current value, oscillator accuracy, ToF resolution, measurement range, flash capacity, temperature range, or absolute timing accuracy, so those values require confirmation in the datasheet or device evaluation before design release. The listed operating supply range is 2.3 V to 3.6 V. The integrated real-time clock and flash support metering designs that need timekeeping and persistent measurement data alongside ultrasonic time-of-flight conversion. The 16 Hz maximum event-timing frequency is particularly relevant when the meter must update more frequently than the MAX35101. Firmware, calibration, echo detection, and time-of-digital compensation still determine achievable accuracy and must be evaluated with real transducers and meter mechanics. Typical uses include ultrasonic heat meters, water meters, and gas meters. An Analog Devices evaluation kit installs the MAX35103EHJ+ and includes a USB-to-SPI interface plus graphical software for exercising device functionality. The supplied distributor records list the MAX35103EHJ+ in a 32-TQFP package and identify it as a CMOS-input, CMOS-output time-to-digital converter IC. For PCB design, place decoupling and timing-critical paths according to the manufacturer layout guidance and keep the ultrasonic analog front end away from switching nodes and digital return-current paths. Validate transducer drive amplitude, receive gain, threshold timing, clock calibration, and flash endurance under the intended flow, temperature, and supply conditions. Do not infer production suitability from the general-purpose EV kit alone.

RFQ İletişim
MAX354CWE+ 8:1 Fault-Protected Analog Multiplexer | Analog Devices
MAX354CWE+

MAX354CWE+ 8:1 Fault-Protected Analog Multiplexer | Analog Devices

The Analog Devices MAX354CWE+ is a single 8:1 fault-protected analog multiplexer with 350 ohm on-resistance, housed in a 16-pin SOIC package. It uses a series N-channel, P-channel, N-channel protection structure to withstand voltages up to 40 V beyond the supply rails during power-up, power-down, and fault conditions. This makes the device suitable for routing external analog signals into circuitry that requires protection from transient or fault-induced overvoltage. An analog multiplexer is an interface IC that connects one common signal path to multiple input channels through controlled switches. Within the product hierarchy, the MAX354 is a fault-protected analog switch, then an analog multiplexer, then an interface IC used in broader signal-routing and power-management systems. Unlike a mechanical relay, it provides compact electronic channel selection, while its internal protection structure adds resilience beyond that of an unprotected CMOS multiplexer. The MAX354 family combines an 8:1 multiplexing arrangement with an on-resistance of 350 ohm. Its fault-protection architecture is designed to protect downstream circuitry when an input can be driven above or below the normal supply range. The MAX354 is the single-channel version in a family that also includes the MAX355, which is a dual 4:1 fault-protected analog multiplexer. This distinction is important when selecting between single-ended eight-way routing and two independent four-way muxes. The MAX354 is intended for analog instrumentation, test and measurement systems, data acquisition modules, industrial control interfaces, and other applications where a protected input must be connected to downstream signal-processing circuitry. Its 16-pin SOIC package supports conventional surface-mount assembly and provides enough pins for the common connection, eight mux inputs, control logic, supply rails, and fault-protection elements. Use the manufacturer pin-description table to assign PCB nets and verify the exposed electrical characteristics before production release. A critical design consideration is the relationship between external signal amplitude and the device supply range. The protection structure is intended to tolerate overvoltage beyond the rails, but it does not eliminate the need to review absolute maximum ratings, input-current limits, channel leakage, and operating conditions. Designers should also account for the 350 ohm on-resistance when calculating source impedance, attenuation, bandwidth, and downstream amplifier loading. This page combines the manufacturer’s fault-protection description with distributor package information, replacement analysis, and practical PCB guidance. It distinguishes verified device facts from parameters that require confirmation in the manufacturer datasheet, helping engineers plan footprint, sourcing, and signal-path design before schematic release.

RFQ İletişim
MAX354EWE+ 8:1 Fault-Protected Analog Multiplexer | Analog Devices
MAX354EWE+

MAX354EWE+ 8:1 Fault-Protected Analog Multiplexer | Analog Devices

The Analog Devices MAX354EWE+ is a single 8:1 analog multiplexer with a 350 ohm on-resistance, fault protection to 40 V beyond the supply rails, and a 16-pin SOIC package. It routes one of eight single-ended analog inputs to a common output while protecting sensitive downstream circuitry during power-up, power-down, and fault conditions. An analog multiplexer is an interface IC that connects multiple signal paths to a shared processing or measurement resource. The MAX354 belongs to the broader switch and multiplexer hierarchy, where multiplexing reduces the number of input channels, converters, amplifiers, or external connectors required by an electronic system. Its fault-protected architecture is especially useful when external signals can exceed the nominal supply range during startup or abnormal operating conditions. The MAX354EWE+ provides eight channels, a 350 ohm on-resistance, and protection against overvoltage up to 40 V beyond the supply rails. These characteristics make the device relevant to data acquisition, instrumentation, test systems, industrial control, and battery-powered equipment. The MAX354/MAX355 family uses a series N-channel, P-channel, N-channel structure that isolates protected downstream components from excessive input voltage. The device is specified as a single-ended multiplexer in a 16-SOIC surface-mount package. Its industrial temperature grade suits equipment expected to operate across demanding environmental conditions. Because on-resistance and protection behavior influence signal fidelity and system reliability, designers should account for the complete source impedance, selected channel, supply state, and external signal amplitude rather than treating the switch as an ideal conductor. Typical uses include eight-channel sensor selection, industrial measurement front ends, automated test equipment, and embedded control systems that need to share an analog-to-digital converter or signal-conditioning channel. In these systems, the multiplexer reduces channel count while the fault-protected structure provides additional tolerance for externally driven signals. The final input range must remain compatible with the complete signal chain and device operating limits. A key design consideration is the relationship between the multiplexer, the protected signal source, and downstream circuitry. Keep sensitive return paths compact, observe the manufacturer’s pin configuration when assigning inputs and enables, and evaluate the switch resistance in the source impedance of the selected channel. The 350 ohm on-resistance is especially important for high-impedance sensors and low-amplitude measurements. This product page combines the manufacturer’s multiplex function, protection characteristics, package details, application analysis, and parameter-level comparison. It also distinguishes device-family options from true pin-compatible drop-in replacements so that PCB changes are not mistaken for a straightforward substitution.

RFQ İletişim
MAX355CWE+ - Dual 4:1 Fault-Protected Analog Mux | Maxim
MAX355CWE+

MAX355CWE+ - Dual 4:1 Fault-Protected Analog Mux | Maxim

The Maxim Integrated MAX355CWE+ is a dual 4:1 fault-protected analog multiplexer with two independently controlled 4:1 switches, 350 ohm on-resistance, and a 16-pin WSOIC package. Its 4.5 V to 36 V operating supply range and protection against overvoltage up to 40 V beyond the supply rails make it suitable for routing signals through systems where input pins may temporarily exceed the normal supply limits during power-up, power-down, or fault conditions. An analog multiplexer is a switching interface that connects one signal source to one of several destinations. In this case, each MAX355CWE+ channel implements a 4:1 configuration, allowing two multiplexers to route four sources per channel. Within the broader semiconductor hierarchy, the MAX355CWE+ is an analog switch IC, then a multiplexer, then an interface IC used to connect external signals to analog processing circuitry. Key electrical characteristics include a maximum on-resistance of 350 ohms, maximum off leakage of 500 pA, and crosstalk of -92 dB at 100 kHz. The 350 ohm resistance is suitable for moderate-impedance sensor, measurement, and control paths rather than high-bandwidth, low-impedance video networks. Fault protection extends to 40 V beyond the supply rails, helping isolate sensitive downstream circuitry during abnormal input conditions. The device uses a series N-channel, P-channel, and N-channel switching structure to provide fault protection. Its dual-mux architecture makes it useful where multiple analog inputs must be selected under software or hardware control. Control inputs allow the selected paths to be changed without mechanical switching, making the MAX355CWE+ appropriate for test systems, industrial controls, data acquisition modules, and instrumentation. Typical uses include battery-powered monitoring equipment, industrial sensor interfaces, laboratory measurement systems, and analog test equipment. The 4.5 V minimum supply supports systems operating from a 5 V rail, while the 36 V maximum expands applicability to higher-voltage industrial environments. Protection is especially relevant where an external cable or sensor may present an overvoltage before system power stabilizes. Designers should verify the input and output voltage limits against the specific fault condition and avoid treating the 40 V protection rating as a continuous operating rating. Keep analog routing paths away from high-current switching nodes, provide a stable bypass capacitor near the supply pins, and use high-impedance sensing circuits to reduce errors caused by the 350 ohm on-resistance. This page combines the MAX355CWE+ electrical characteristics, application guidance, package information, and verified drop-in alternatives to support faster component selection and PCB replacement decisions.

RFQ İletişim
MAX355EWE+ Dual Fault-Protected 4:1 Mux | Maxim
MAX355EWE+

MAX355EWE+ Dual Fault-Protected 4:1 Mux | Maxim

The Maxim Integrated MAX355EWE+ is a dual 4:1 analog multiplexer with two independent SP4T switching circuits, a 350 ohm on-resistance, and fault protection to 40 V beyond the supply rails. It operates from 4.5 V to 36 V and is packaged in a 16-pin wide SOIC configuration for surface-mount industrial electronics. An analog multiplexer routes one of several analog inputs to an output according to digital select-control signals. The MAX355 family belongs to the analog-switch and multiplexer hierarchy, where switch resistance, channel isolation, logic levels, supply range, and fault tolerance determine whether a device is suitable for precision measurement, test equipment, battery systems, or signal-routing networks. The MAX355EWE+ combines two 4:1 muxes in one 16-pin package. Its principal electrical characteristics include 2 circuits, 8 selectable channels, 350 ohm on-resistance, and a 4.5 V to 36 V operating supply range. The series N-channel, P-channel, N-channel switch architecture is designed to limit fault current and protect downstream circuitry during power-up, power-down, and overvoltage conditions. Fault protection extends as much as 40 V beyond the positive and negative supply rails. This characteristic is important when an external signal may exceed the local supply range during startup or an electrical fault. The protection structure is intended to preserve sensitive measurement circuits rather than serve as a substitute for normal operating-voltage design or external surge protection. Typical uses include battery-powered instrumentation, programmable test and measurement systems, industrial sensor acquisition, analog signal routing, and communication equipment that must select among several analog inputs. The wide 4.5 V to 36 V supply span supports both low-voltage portable systems and higher-voltage industrial signal chains. PCB design should reserve the complete 16-pin footprint exactly as defined by the manufacturer pin description and place bypass capacitors close to the supply pins. Before substituting the device into an existing board, verify control-logic thresholds, input signal range, switch timing, and the specific operating-temperature grade. This page combines the manufacturer product information with practical fault-protection guidance, same-footprint alternatives, sourcing instructions, and design considerations for engineers evaluating the MAX355EWE+ as a protected dual analog multiplexer.

RFQ İletişim
MAX358CWE+ - Fault-Protected 8:1 Analog Multiplexer | ADI
MAX358CWE+

MAX358CWE+ - Fault-Protected 8:1 Analog Multiplexer | ADI

Analog Devices MAX358CWE+ is a fault-protected, 8-channel single-ended analog multiplexer with an 8:1 configuration, 1.8 kOhm on-resistance and approximately 1 MHz bandwidth in a 16-pin SOIC package. According to the manufacturer product page, the MAX358 family is designed for multiplexers and demultiplexers that must withstand fault conditions beyond their normal supply rails. An analog multiplexer is an interface IC that routes one of several input channels to a shared output or measurement path. The MAX358 belongs to the broader hierarchy of analog switches, multiplexers, interface ICs and semiconductors. By selecting among eight single-ended inputs with controlled switches, it reduces the number of signal lines required between sensors, test points, data-conversion systems and other analog circuits. The MAX358 family combines an 8:1 configuration with 1.8 kOhm on-resistance and approximately 1 MHz bandwidth. Its listed operating supply range is 4.5 V to 18 V, while the fault-protection architecture provides protection for overvoltage conditions extending to ±35 V beyond the supply rails when power is removed. The manufacturer describes the implementation as a series N-channel, P-channel, N-channel structure. MAX358 is the single-ended member of a related fault-protected multiplexer family. The MAX359 provides a four-channel differential configuration, while the MAX358 is intended for eight-channel single-ended routing. The device uses address and control inputs to select the active path and supports analog signal multiplexing in systems where input faults, limited board area and modest bandwidth are more important than very low on-resistance. Typical uses include data acquisition, instrumentation, test and measurement, industrial control, battery monitoring and embedded analog signal routing. The 1 MHz bandwidth is suitable for many sensor and control signals, while the fault-protection feature helps isolate downstream circuitry from excessive input voltage. System designers should still validate signal levels, transition behavior and protection conditions against the manufacturer datasheet. PCB implementation requires careful routing of the selected analog path and control signals to prevent interference between channels. Place the multiplexer close to the source or destination of the routed signal, maintain a continuous ground reference, and follow the datasheet layout guidance for bypass capacitors and exposed routing areas. This product page combines the manufacturer specifications with practical design guidance, package information, sourcing workflow and verified drop-in alternatives. It is intended to help engineers determine whether the MAX358CWE+ fits an analog routing design before detailed circuit simulation and board validation.

RFQ İletişim
MAX358EPE+ - 8:1 Fault-Protected Analog Multiplexer | Analog Devices
MAX358EPE+

MAX358EPE+ - 8:1 Fault-Protected Analog Multiplexer | Analog Devices

The Analog Devices MAX358EPE+ is a fault-protected, single-ended 8:1 analog multiplexer with 1.8 kOhm on-resistance in a 16-pin PDIP package. It routes one of eight input channels to a common output while providing fault protection, power-off isolation, and an operating temperature range of -40°C to +85°C. The device is intended for systems where an input may experience voltage excursions beyond the normal supply rails. An analog multiplexer is an interface IC that connects multiple signal sources to one processing channel. The MAX358 family uses this switching architecture to reduce the number of converters, sensor inputs, or control lines required by a measurement system. In the hierarchy of semiconductor devices, it is an analog switch IC, an interface IC, and ultimately a discrete analog function rather than a digital logic component. The MAX358EPE+ provides eight single-ended channels, 1.8 kOhm on-resistance, and fault protection covering ±35 V beyond the supply rails. Power-off isolation prevents connected sources from being significantly influenced when the device is unpowered. These characteristics make the multiplexer useful for data acquisition, industrial control, test equipment, and instrumentation where signal routing and input protection must coexist in a compact package. The 16-pin PDIP construction supports through-hole assembly and straightforward inspection or rework on suitable boards. The MAX358 family is identified by Analog Devices as a production product. Circuit designers should still verify signal amplitude, supply voltage, leakage, switching timing, and channel capacitance against their exact system requirements before finalizing the PCB and input-protection network. Typical uses include multiplexed sensor acquisition, programmable instrumentation, industrial control interfaces, automated test equipment, and data-logging modules. In these applications, the common output can be connected to an ADC or measurement front end while the address and enable controls select the required channel. Care is required when switching high-impedance sources because off leakage, charge injection, and settling time influence measurement accuracy. A practical design priority is to preserve the mux's fault-protection capability rather than placing unrestricted external voltages directly on every input. Confirm the absolute maximum conditions and ensure that control logic, supply sequencing, and external clamping are compatible with the selected operating state. This page also consolidates practical selection guidance, verified alternatives, and design considerations for engineers evaluating the MAX358EPE+.

RFQ İletişim
MAX361CSE+ - Quad SPST Analog Switch | Analog Devices
MAX361CSE+

MAX361CSE+ - Quad SPST Analog Switch | Analog Devices

Analog Devices MAX361CSE+ is a precision, quad, single-pole single-throw analog switch with four normally closed switches, packaged in a 16-pin SOIC. The device provides low channel on resistance of less than 85 ohms, with on-resistance matching maintained within 3 ohms between channels. Its on resistance remains flat across the analog signal range, with a maximum change of 9 ohms. The MAX361CSE+ is designed for precision signal-routing systems where repeatable resistance, low leakage, and consistent channel behavior are important. An analog switch is a semiconductor device that routes analog signals between terminals under digital control. The MAX361CSE+ belongs to the analog switch and multiplexer hierarchy, where a multiplexer combines switching functions with signal selection. Its four normally closed SPST channels default to the connected state when the control input is inactive. This architecture is useful in test systems, measurement instruments, audio paths, sensor interfaces, and communication equipment that require controlled switching of low-voltage signals. The primary benefit of the MAX361CSE+ is channel-to-channel consistency. According to the Analog Devices MAX361 product page, the device guarantees less than 85 ohms of on resistance and matching within 3 ohms among channels. The on-resistance characteristic changes by no more than 9 ohms across the supported analog signal range. These specifications reduce gain error and channel-to-channel variation when the same source resistance, amplifier gain, or measurement calibration is used across multiple switched paths. The MAX361CSE+ contains four independent precision SPST switches, allowing a system to connect or isolate several signal lines without changing the PCB footprint. Its 16-pin narrow SOIC package supports conventional surface-mount assembly and keeps the routing distance between external circuitry and the switch short. The manufacturer identifies the MAX361 family as being in production and lists the MAX361 data sheet as Revision 2. Typical uses include front-end signal selection, instrumentation amplifiers, automated test equipment, data acquisition systems, and audio routing networks. Because the switches are normally closed, they can also preserve signal continuity during control-signal transitions or provide a default connection when an external controller is unavailable. Designers should still account for injected power, off-state isolation, control logic levels, and signal amplitude when constructing the surrounding analog circuit. Layout and signal integrity require attention around high-impedance analog paths. Keep input and output traces short, use a continuous ground reference, and avoid routing sensitive signals next to clocked or switching circuitry. Verify the control levels and operating conditions in the MAX361 data sheet before relying on a default state during power-up. Decoupling and protection components should be selected from the actual signal bandwidth, source impedance, and external voltage limits. This product page combines the MAX361CSE+ technical description with package information, application guidance, design notes, and a focused comparison against identified same-package alternatives. It is intended to help engineers distinguish the normally closed MAX361 from other switching functions and to plan PCB, sourcing, and signal-path decisions around the verified 16-pin SOIC implementation.

RFQ İletişim
MAX362CSE+ - 4-Channel SPST Analog Switch | Analog Devices
MAX362CSE+

MAX362CSE+ - 4-Channel SPST Analog Switch | Analog Devices

The Analog Devices MAX362CSE+ is a precision quad, single-pole single-throw analog switch with four normally open switches, packaged in a 16-pin SOIC. The device provides a 1:1 signal configuration and an on resistance of 85 ohms, making it suitable for routing precision analog signals in test, measurement, instrumentation, and communication equipment. An analog switch is a semiconductor device that connects or isolates circuit nodes under digital control. A single-pole single-throw, or SPST, switch contains one signal path that is either connected or disconnected. The MAX362 uses four normally open channels, so each channel is off during its inactive state and connects the selected signal when the corresponding control input is asserted. This topology is useful when a system must route one source to one destination without connecting the active path permanently. The MAX362 family is designed for precision signal handling. According to the Analog Devices MAX362 product page, the on resistance is less than 85 ohms, channel-to-channel matching is guaranteed within 3 ohms, and resistance variation across the analog signal range is limited to a maximum change of 9 ohms. These characteristics support predictable signal attenuation when the same switch is used with different channels or operating signal levels. The MAX362CSE+ provides four independently controlled switch channels in a 16-SOIC package. The MAX362 product family is also available in complementary normally closed form as the MAX361, allowing complementary routing behavior to be considered when designing control logic. The MAX362CSE+ ordering suffix denotes the leaded SOIC package configuration identified in the product listing. Typical applications include precision signal routing, bench-test equipment, data-acquisition systems, communication-channel selection, and analog measurement paths. Because the switch resistance and matching characteristics are central to its performance, system-level calculations should include the effective source and load impedances, expected signal amplitude, settling behavior, and the contribution of switch on resistance. When laying out a board around the MAX362CSE+, keep analog input and output traces short and connect the device ground pins to a low-impedance ground plane. Place nearby bypassing capacitors at the supply entry point and keep digital control traces away from sensitive analog paths. Review the manufacturer datasheet for the exact pin assignments, absolute maximum ratings, recommended operating conditions, and electrical characteristics before releasing the layout. This product page combines the manufacturer family description, package identification, sourcing information, practical layout guidance, and a structured comparison framework to support component selection and PCB design. It also distinguishes verified product facts from parameters that require confirmation in the MAX362 datasheet.

RFQ İletişim
MAX362ESE+ - 85Ω Quad SPST Analog Switch | Analog Devices
MAX362ESE+

MAX362ESE+ - 85Ω Quad SPST Analog Switch | Analog Devices

Analog Devices MAX362ESE+ is a precision, quad, single-pole single-throw analog switch with four normally open channels, a maximum on resistance of 85Ω, and a 16-pin SOIC package. The switch is designed for controlled routing of low-frequency analog signals where consistent channel resistance, low leakage, and a compact surface-mount footprint are important. An analog switch is an integrated semiconductor device that connects or isolates circuit nodes under digital control. A single-pole single-throw switch provides one signal path that is normally disconnected and closes when its control input is asserted. The quad architecture gives the MAX362ESE+ four independent switch paths, reducing component count in test systems, measurement instruments, signal-conditioning circuits, and controlled analog-routing designs. The MAX362 family provides on-resistance below 85Ω across the analog signal range. Analog Devices specifies channel matching within 3Ω and a maximum on-resistance change of 9Ω, helping preserve amplitude relationships when signals pass through multiple channels. These characteristics are especially useful when attenuation, calibration, or measurement accuracy depends on similar resistance among switched paths. The MAX362ESE+ differs from the MAX361 family member through its normally open switch configuration: MAX362 uses normally open channels, while MAX361 uses normally closed channels. Its 1:1 circuit arrangement means the device does not inherently invert the signal. The industrial temperature-grade designation and 16-lead SOIC packaging support conventional surface-mount assembly for industrial and instrumentation applications. Typical uses include low-frequency sensor multiplexing, sample-and-hold signal routing, automated test equipment, programmable gain networks, and laboratory measurement interfaces. The four channels can route related nodes to a common analog processing chain, although system timing and control logic must ensure that only the intended channel is closed when signal integrity matters. Layout should keep analog traces short and place bypass and interface components near their associated pins. Control signals should transition cleanly, and unused control or signal pins should be connected according to the manufacturer pin-description table. Because switch resistance can vary with signal amplitude, verify the complete signal path and account for Ron when designing precision dividers, current loops, or low-amplitude sensor interfaces. This page consolidates the manufacturer switch characteristics, package information, sourcing workflow, verified replacement reference, and practical implementation guidance. It is designed to help engineers evaluate the MAX362ESE+ for new analog-routing designs and assess PCB reuse without relying on generic analog-switch descriptions.

RFQ İletişim
MAX365CPE+ - Quad SPST Analog Switch | Maxim Integrated
MAX365CPE+

MAX365CPE+ - Quad SPST Analog Switch | Maxim Integrated

The Maxim Integrated MAX365CPE+ is a precision quad single-pole, single-throw analog switch with four normally open switches, a 1:1 configuration, and a 16-pin PDIP package. Its on-resistance is specified below 85 ohm, with channel-to-channel matching maintained within 2 ohm and on-resistance variation limited to 9 ohm across the analog signal range. These characteristics make the device suitable for precision analog routing where consistent channel resistance simplifies calibration of downstream measurement and signal-conditioning circuits. An analog switch is a semiconductor device that connects or disconnects an analog signal path under digital control. The MAX365CPE+ belongs to the analog switch and multiplexer hierarchy, providing four independent switching paths rather than multiplexing several inputs onto a shared output. Each switch is normally open, so the connected state exists only when the control input commands the device, which helps prevent unintended signal paths during power-up and reset conditions. The main engineering benefits of the MAX365 family are its low on-resistance, tightly matched channels, and flat resistance behavior. Matching within 2 ohm minimizes gain error between channels, while the maximum 9 ohm variation over the signal range reduces the gain error that would otherwise appear as the analog level changes. These characteristics are particularly useful in instrumentation, test systems, data converters, and precision signal-conditioning boards where repeatable channel impedance supports accurate measurements. The MAX365CPE+ uses four independently controlled switches. Because the control logic operates from the same single supply as the analog switches, only one supply rail is required for basic operation. Keep control inputs at valid logic levels whenever an analog input may exceed the supply range, and confirm the absolute maximum ratings in the manufacturer datasheet before applying signals above the switch supply voltage. Typical uses include sensor selection, sample-and-hold front ends, test-point routing, programmable gain stages, and isolation of external analog inputs. The four switch channels can also be combined for wider routing functions, although the control architecture must keep the individual on-resistance values in mind when several closed channels share the same signal path. The 16-pin PDIP package is appropriate for through-hole prototype boards, legacy control systems, and industrial assemblies that favor a socketed or readily inspected package. Its relatively large pin pitch simplifies probing and rework compared with fine-pitch surface-mount alternatives. During layout, route analog traces away from control and clock lines, and place the device close to the switched nodes to minimize parasitic pickup in high-impedance circuits. This page consolidates the manufacturer product information with practical routing guidance, precision-impedance considerations, package details, and ordering guidance for engineers evaluating the MAX365CPE+ in analog signal-path designs.

RFQ İletişim
MAX368CPN+ - 8:1 Fault-Protected Analog Mux, 1.8kOhm | Maxim
MAX368CPN+

MAX368CPN+ - 8:1 Fault-Protected Analog Mux, 1.8kOhm | Maxim

The Analog Devices (Maxim Integrated) MAX368CPN+ is a fault-protected 8-channel (8:1) analog multiplexer with internal data latches and a 1.8 kOhm on-resistance, housed in an 18-pin PDIP (0.300 in / 7.62 mm) package. An analog multiplexer is a switch network that selects one of several analog input signals and routes it to a single output under digital control. Within the signal-chain hierarchy, the analog multiplexer sits between sensors or signal sources and amplifiers or ADCs, and is itself a member of the broader analog switch IC family. Fault-protected multiplexers add a critical layer: their inputs tolerate fault voltages far beyond the supply rails, and outputs are forced to a high-impedance state when power is removed, protecting downstream circuitry. Key features of the MAX368 include overvoltage protection up to plus or minus 35V at the analog inputs, channels automatically turned off when power is lost, all digital inputs TTL and CMOS compatible, and internal data latches for channel selection so the addressed channel is held without continuous drive of the address lines. Technical depth: the device operates from plus or minus 15V supplies with 5 nA typical leakage, and switches in approximately 1.5 microseconds on-time and 1 microsecond off-time with break-before-make switching action, ensuring the selected channels never short together during transitions. The C-grade temperature specification covers commercial ranges; E and M grades exist for extended and military environments. Typical applications include industrial data acquisition front ends where wiring faults or misconnection would otherwise destroy a standard CMOS mux, test and measurement input selector stages, and ATE (automated test equipment) channel routing where inputs may exceed supply rails. Design consideration: the 1.8 kOhm on-resistance must be accounted for in settling-time budgets when driving sample-and-hold or ADC inputs, particularly at higher source capacitance. This page synthesizes distributor pricing, verified drop-in grade variants, and practical design notes beyond the summary on the manufacturer datasheet.

RFQ İletişim
MAX368CWN+ - 8:1 Fault-Protected Analog Multiplexer | Analog Devices
MAX368CWN+

MAX368CWN+ - 8:1 Fault-Protected Analog Multiplexer | Analog Devices

The Analog Devices MAX368CWN+ is a single-ended, fault-protected 8:1 analog multiplexer with an on-resistance of 1.8 kOhm, packaged in an 18-SOIC surface-mount package. It is designed for applications that route one of eight analog input channels to a common output while providing controlled fault isolation and latch-based operation. An analog multiplexer is an interface IC that connects multiple signal sources to one shared input on a host circuit. The MAX368CWN+ belongs to the broader multiplexer and demultiplexer hierarchy, where a multiplexer selects among several inputs and a demultiplexer directs one input toward multiple outputs. Its single-ended architecture, 8:1 configuration, and 1.8 kOhm on-resistance make it relevant to compact analog signal-routing systems rather than high-voltage power switching. The principal documented features include an 8:1 single circuit configuration, 1.8 kOhm on-resistance, and an 18-SOIC package. The MAX368 family is identified as a fault-protected analog multiplexer with latch, allowing a system to place a selected channel into a held state during control or fault-management sequences. Its surface-mount construction supports compact PCB layouts while preserving leaded-component handling characteristics associated with the SOIC form factor. Technically, the device uses separate selection and enable controls to route one of eight channels to the common output. Because it is intended for analog signals, channel resistance and leakage behavior are important considerations when the source impedance is high. The 1.8 kOhm specification should be compared with the input impedance of the receiving amplifier, ADC, or instrumentation circuit; otherwise, source-loading errors can reduce signal amplitude and disturb the expected transfer function. Typical uses include sensor-channel selection, test and measurement signal routing, data-acquisition systems, industrial control interfaces, and communication equipment that must connect several low-frequency analog sources to a shared processing channel. The surface-mount 18-SOIC package can also simplify board-level replacement of the non-tape-and-reel MAX368CWN ordering code when the electrical configuration and operating requirements are identical. PCB design should keep selected and unselected analog paths short, provide a solid ground reference, and isolate sensitive routing from switching or digital clock signals. Because the available device data does not publish a complete pin-description table, engineers should use the manufacturer’s MAX368 datasheet when assigning every physical pin and confirming control polarity, fault behavior, and absolute maximum ratings. This page combines the verified product identity, package information, ordering-code distinctions, procurement availability, and replacement analysis with practical guidance for selecting and implementing this multiplexer. It is intended to help engineers distinguish the MAX368CWN+ from related MAX368 ordering codes and determine whether a proposed replacement preserves the required 8:1, single-ended, 18-SOIC configuration.

RFQ İletişim
MAX378CWG+ - 8:1 High-Voltage Fault-Protected MUX | Analog Devices
MAX378CWG+

MAX378CWG+ - 8:1 High-Voltage Fault-Protected MUX | Analog Devices

Analog Devices MAX378CWG+ is a single-ended, 8-channel, 1-of-8 analog multiplexer with a maximum on-resistance of 3.5 kOhm, switching times of 1 us on and 300 ns off, and operation from a single 5 V to 36 V supply or dual ±18 V supplies. It is packaged in a 24-pin SOIC. The device uses a series N-channel/P-channel/N-channel structure to provide fault protection when input voltages remain applied after the supplies are removed. An analog multiplexer is an analog switch that connects one of several inputs to a common output or selects one signal path from multiple candidates. The MAX378 belongs to the analog switch and multiplexer hierarchy, where the 8:1 configuration provides eight single-ended inputs and one output. This makes the device useful for compact signal-routing systems in test equipment, industrial control, instrumentation, and data-acquisition equipment where one source must be selected from several measured or sensed signals. Key features include a maximum on-resistance of 3.5 kOhm, 1 us maximum turn-on time, and 300 ns maximum turn-off time. The fault-protected architecture is especially important in high-voltage systems because the internal transistor arrangement turns the channels off if the supply rails collapse while external input signals are still present. The single 5 V to 36 V or dual ±18 V supply choices support both conventional and bipolar analog systems. The 24-pin SOIC package also provides a surface-mount implementation for industrial and instrumentation equipment. The MAX378 uses a series N-channel, P-channel, and N-channel switch structure. Its digital address and enable controls route the selected analog input to the common output while isolating other channels. The 3.5 kOhm maximum on-resistance is appropriate for medium-impedance measurement paths, control signals, and test points where lower resistance is not essential. Designers should account for this resistance in the source impedance, settling time, and signal-accuracy calculations of the complete measurement chain. Typical applications include automated test systems, battery and power-system monitoring, industrial process control, programmable instrumentation, and multichannel sensor acquisition. In each case, the multiplexer reduces the number of input channels required by the host analog-to-digital converter or measurement circuit. The common MAX378 family also includes the MAX379 differential multiplexer for applications requiring paired signal selection rather than a single-ended 8:1 arrangement. For reliable operation, treat the maximum 36 V single-supply or ±18 V dual-supply limits as absolute constraints. Keep signal paths short, provide a stable low-impedance supply reference, and use suitable protection networks when external inputs can exceed the selected supply range. Verify address transitions, disable timing, settling behavior, and channel isolation in the final analog signal path. This page combines the manufacturer product information with practical routing, protection, timing, and layout considerations. It also organizes the available drop-in information by package and electrical match so engineers can assess replacement decisions without confusing a pin-compatible part with merely similar multiplexer functionality.

RFQ İletişim
MAX378EWG+ - 8:1 Fault-Protected Multiplexer | Analog Devices
MAX378EWG+

MAX378EWG+ - 8:1 Fault-Protected Multiplexer | Analog Devices

The Analog Devices MAX378EWG+ is an 8-channel, single-ended 1-of-8 multiplexer with a specified on-resistance of 3.5 kOhm, fault protection, and a 24-pin SOIC package. The device is designed for routing one of eight analog inputs to a common output while providing protection when supply voltages are inadvertently removed from a powered system. The MAX378 uses a series N-channel, P-channel, and N-channel switch arrangement that supports fault-protected operation in demanding measurement and control circuits. A multiplexer is an analog switch that connects multiple signal sources to one destination. In the broader hierarchy of electronic components, the MAX378EWG+ is an analog multiplexer, an analog switch, an interface IC, and ultimately a semiconductor. Its eight-to-one configuration reduces the number of external signal lines needed when several sensors, voltage sources, or measurement channels must be evaluated by one downstream converter. The fault-protected architecture is particularly useful when an input may remain energized while the device's own supply rails are off. The manufacturer identifies the MAX378 as an 8-channel, high-voltage, fault-protected multiplexer and lists it in production. Its principal specifications include an 8:1 configuration, one multiplexer circuit, 3.5 kOhm on-resistance, and a 24-SOIC package. The MAX378EWG+ ordering code is listed by distributors as a 24-pin SOIC analog switch or multiplexer. The similarly named MAX379 is a different 4-channel differential multiplexer and therefore is not an interchangeable functional substitute for the single-ended MAX378. The N-channel, P-channel, and N-channel topology distinguishes this device from a basic eight-channel analog multiplexer. According to the Analog Devices MAX378 product page, the fault-protection structure causes all mux channels to turn off if the power supplies are inadvertently turned off while input voltages remain applied. This behavior limits unintended signal paths during an abnormal power sequence and is valuable in equipment where external sources can outlive the local control electronics. Typical uses include battery-powered instrumentation, industrial test equipment, data acquisition, automated measurement systems, and analog sensor interfaces. The 8:1 organization is useful when one analog-to-digital converter or measurement front end must interrogate multiple inputs without requiring a separate switch for every channel. Engineers should also account for the relatively high 3.5 kOhm on-resistance when designing sensors that require low source impedance or when calculating the resulting signal attenuation. For layout and protection, place the multiplexer near the routed analog signals, keep the selected-channel traces compact, and provide a defined return path for every switched input. Review the manufacturer's datasheet pin description, absolute maximum ratings, and typical application circuit before connecting high-voltage sources. The fault-protection feature should not be interpreted as permission to exceed those ratings or as a substitute for external surge protection. This product page consolidates the manufacturer identity, package, multiplexing configuration, fault-protection architecture, ordering information, sourcing guidance, and design considerations into an engineering-focused reference. It also distinguishes true drop-in alternatives from related devices whose channel count, signal architecture, or package implementation differs, helping PCB designers avoid substitutions that require schematic or layout changes.

RFQ İletişim
MAX379CPE+ - Fault-Protected 4:1 Multiplexer | Maxim Integrated
MAX379CPE+

MAX379CPE+ - Fault-Protected 4:1 Multiplexer | Maxim Integrated

The Maxim Integrated MAX379CPE+ is a high-voltage, fault-protected analog multiplexer with two 4:1 switches, a 3.5 kOhm on-resistance, and a 16-pin PDIP package. It is a differential 2-of-8 multiplexer, allowing eight source inputs to be organized into four selectable differential pairs for measurement, routing, and instrumentation systems. A multiplexer is an analog switch network that routes one of several signal sources to a common output. The MAX379 belongs to the broader analog switch and multiplexer hierarchy within interface ICs. Its differential architecture is intended for paired signals, while its 4:1 configuration provides four selections per switch. The series N-channel, P-channel, and N-channel structure is specifically designed to improve protection when the device supplies are off but external input voltages remain present. The key features of the MAX379CPE+ include its fault-tolerant input structure, two independent 4:1 circuits, and 3.5 kOhm switch resistance. Differential routing reduces the influence of common-mode effects when paired signals are measured together. The high-voltage, fault-protected design is useful when transient or powered-off conditions could otherwise stress the input network. Two circuits in one package also reduce board area compared with separate single-ended or differential switch assemblies. Technically, the MAX379 is described as an 8-channel, high-voltage, fault-protected multiplexer. The manufacturer identifies the MAX379 as a four-channel differential, 2-of-8 multiplexer, while the MAX378 in the same family is an eight-channel single-ended, 1-of-8 device. During an unintended power-off condition, the MAX379 channels turn off and the input current falls to only a few nanoamperes. This behavior helps isolate applied signals from the internal switching path when supply power is absent. Typical uses include automated test equipment, data-acquisition systems, battery or power-system monitoring, industrial control interfaces, and laboratory measurement equipment. The differential configuration is especially appropriate for bridge sensors, paired analog channels, and systems where a common measurement reference is required. PCB layout should preserve the pin assignments of the 16-pin PDIP package and route high-impedance analog nodes with short, guarded traces. Check signal amplitude and fault conditions against the manufacturer operating limits before connecting external sources. Because this is a through-hole package, component height, lead spacing, and connector orientation also require mechanical validation. This product page combines the manufacturer function description, exact distributor package and resistance information, lifecycle context, and practical guidance for selecting, sourcing, and implementing the MAX379CPE+ in analog-routing systems.

RFQ İletişim
MAX379CWG+ - Fault-Protected 4:1 Multiplexer | Maxim Integrated
MAX379CWG+

MAX379CWG+ - Fault-Protected 4:1 Multiplexer | Maxim Integrated

The Maxim Integrated MAX379CWG+ is a high-voltage, fault-protected analog multiplexer with two 4:1 circuits, an on-resistance of 3.5 kOhm, and a 24-pin SOIC package. It selects four differential signal pairs, or eight single-ended inputs in differential operating mode, making it suitable for routing controlled signals in instrumentation, test, measurement, and industrial systems. The MAX379 family is designed to limit fault-current exposure when input voltages remain present while the device supplies are turned off. An analog multiplexer is an interface IC that connects multiple signal paths to a smaller number of shared pins. The MAX379 belongs to the broader multiplexer hierarchy, where its differential 4:1 architecture reduces the number of external connections required by a system with several paired inputs. This is particularly useful when board space, connector count, or routing complexity must be controlled without sacrificing selectable signal channels. Key features include two independent 4:1 circuits, 3.5 kOhm on-resistance, an eight-channel high-voltage fault-protected configuration, and operation from dual supply rails. The manufacturer describes the implementation as a series N-channel, P-channel, and N-channel structure. This arrangement provides meaningful fault protection by turning the channels off when the supplies are removed while signal inputs can still be present, limiting unintended current paths. The MAX379CWG+ is a differential rather than single-ended multiplexer. Each selected channel can carry a pair of related signals, supporting balanced measurement, instrumentation, or test systems where signal polarity and common-mode behavior matter. Its 24-pin SOIC footprint is a surface-mount package intended for conventional PCB assembly, while the operating limits and exact channel ratings should be checked against the manufacturer datasheet before using it outside laboratory voltages. Typical uses include automated test equipment, data-acquisition systems, industrial control interfaces, oscilloscope input routing, and multichannel sensor conditioning. It is particularly appropriate when multiple high-impedance sources must be connected to downstream instrumentation. Designers should account for the 3.5 kOhm on-resistance, assess leakage and off-channel behavior, and ensure that external circuitry keeps faulted inputs within the absolute maximum ratings. For a robust layout, place the device close to the multiplexer bus and use a quiet ground-plane connection. Signal traces should avoid crossing high-current switching paths, and unused inputs should be handled according to the datasheet guidance. Supply decoupling must follow the manufacturer recommendation, while external series resistance may be needed to limit fault current in higher-energy systems. This product summary combines the manufacturer's device description with package, interface, and application analysis, helping engineers identify whether the MAX379CWG+ provides the required differential channel count and fault-protected behavior. The accompanying comparison, pinout, sourcing, and design guidance make the selection process more practical than a basic distributor listing alone.

RFQ İletişim
MAX381CPE+ - Dual 35Ω SPST Analog Switch | Maxim Integrated
MAX381CPE+

MAX381CPE+ - Dual 35Ω SPST Analog Switch | Maxim Integrated

Maxim Integrated MAX381CPE+ is a dual, single-pole single-throw normally open CMOS analog switch with 35 Ω on-resistance, supplied in a 16-pin PDIP package. The device operates from 3 V to 15 V, supports single-supply or bipolar operation, and is designed to route low-voltage analog signals with low on-resistance and rail-to-rail signal handling. A CMOS analog switch is an integrated semiconductor device that uses controlled transistors to connect or disconnect an analog signal path. The MAX381/MAX383/MAX385 family comprises precision, low-voltage switches for instrumentation, test equipment, control systems, and signal-routing applications. Within the broader semiconductor hierarchy, an analog switch belongs to the interface-IC category and provides a controllable connection between an input terminal and an output terminal. The MAX381CPE+ contains two independent SPST, normally open switch circuits in a 1:1 configuration. Its specified 35 Ω on-resistance minimizes signal attenuation in moderate-impedance analog systems. The device also features matched channels, with a specified channel-to-channel on-resistance matching of 500 mΩ, helping preserve balance in differential or dual-channel signal paths. Analog-signal performance includes charge injection of 2 pC, off-state channel capacitance of 12 pF, and crosstalk of -90 dB at 1 MHz. The MAX381 family supports both single-supply and bipolar-supply operation, allowing the switch to process signals referenced to ground or operate within positive and negative voltage rails. Its normally open configuration keeps the switched paths disconnected when the control state is inactive. Typical uses include precision measurement front ends, automated test equipment, sensor signal routing, sample-and-hold circuits, and industrial control systems. The two integrated switches can route two related channels when matched behavior is useful, or independently route separate low-voltage signals. The 16-pin PDIP package also supports through-hole prototyping and legacy industrial equipment where surface-mount conversion would be inconvenient. When laying out a design, place the IC close to the switched signal paths and keep analog traces short to minimize parasitic capacitance and interference. Treat the control inputs as logic signals while ensuring that every driven input remains within the device's specified supply-voltage limits. Verify signal amplitude, bandwidth, charge injection, and off-state leakage against the application before committing to a high-impedance instrumentation design. This product page combines the MAX381CPE+ electrical characteristics, package details, lifecycle information, sourcing workflow, application guidance, and verified cross-reference analysis. It also distinguishes true pin-and-package drop-in options from related switches that use different packages or implement different circuit topologies.

RFQ İletişim
MAX383CSE+ - Dual Precision SPDT Analog Switch | Analog Devices
MAX383CSE+

MAX383CSE+ - Dual Precision SPDT Analog Switch | Analog Devices

The Analog Devices MAX383CSE+ is a dual precision, low-voltage CMOS analog switch with two independently controlled single-pole double-throw channels, less than 35 ohm on-resistance, and operation from +3 V to +15 V. The device is packaged in a 16-pin SOIC for surface-mount designs that require low-leakage, low-charge-injection signal routing. An analog switch is a semiconductor device that connects or disconnects an electrical signal path under digital control. The MAX383 belongs to the analog-switch and multiplexer hierarchy, combining low-voltage CMOS construction with precision on-resistance characteristics. Its two SPDT switches can select between two signal sources for each channel, making the device useful for analog signal multiplexing, source selection, test-equipment routing, and bidirectional signal-path control. Key characteristics include on-resistance below 35 ohm, channel-to-channel matching within 2 ohm, flat on-resistance across the specified analog signal range, and operation in either single-supply or bipolar-supply systems. According to the Analog Devices MAX383 product page, the MAX381, MAX383, and MAX385 family uses precision, low-voltage analog switches, while the MAX383 specifically provides two normally open and two normally closed poles. This switching arrangement supports complementary routing rather than simple on/off isolation. The MAX383 supports +3 V to +15 V single-supply operation and ±3 V to ±8 V bipolar-supply operation. These ranges make it appropriate for low-voltage instrumentation, industrial control, communications, and measurement systems. Its low on-resistance can reduce signal attenuation, while matched channels help minimize path-to-path gain variation. The guaranteed charge injection of less than 5 pC and off-channel leakage below 2.5 nA at +85 °C are particularly useful when switching precision or high-impedance signals. Analog Devices also identifies the MAX383 as pin-compatible with the DG401, DG403, and DG405. These compatibility relationships allow engineers to evaluate the MAX383 in existing routed designs while still checking control logic, supply level, signal range, and electrical limits against the complete manufacturer datasheet. The device also supports TTL/CMOS-compatible logic, making it practical to combine with common microcontroller and digital control systems. PCB implementation requires care around high-impedance nodes. Keep routing short, provide a stable ground reference, and avoid placing sensitive analog traces beside fast digital or switching-converter paths. Input and output traces should not be forced beyond the device's absolute-maximum ratings, and control inputs must remain within their specified logic thresholds. The SOIC-16 outline supports conventional surface-mount assembly and provides adequate routing space for two complete SPDT channels. This page consolidates manufacturer specifications, package details, sourcing guidance, and design-oriented guidance into one engineering reference. It also identifies verified pin-compatible options while clearly separating exact drop-in candidates from functionally related devices that require a different package or a full electrical review.

RFQ İletişim