AD526BD - 16x SPGA, 1-16x Gain | Analog Devices | Instrumentation
MPN: AD526BD ✓ AktifAD526BD Genel Bakış
A software-programmable gain amplifier, or SPGA, is a gain-control IC that combines an amplifier with a digitally selectable resistive network. In the signal-chain hierarchy, the AD526BD belongs to the amplifier IC family and specifically to the programmable-gain-amplifier category used ahead of converters, meters, and data-acquisition systems. The latched digital interface allows a processor or controller to select gain while preserving a stable analog operating point during measurement.
The AD526 family provides binary gains from 1 through 16 and supports a two-chip cascade mode that extends the available binary gain range to 256. According to the Analog Devices AD526 data sheet, maximum gain error is 0.01% for the C-grade device and 0.02% for the A-grade device, while gain drift over temperature is specified at 0.5 ppm/°C. These characteristics make gain programming useful when one analog input path must accommodate signals with widely different amplitudes.
The AD526BD combines its amplifier, internal resistor network, and TTL-compatible latched inputs in one monolithic device. That integration removes the need for external matched gain resistors and reduces circuit area. TTL-compatible control inputs also simplify interfacing with conventional digital logic, although the system designer must still observe the required input timing, supply sequencing, and grounding practices specified in the manufacturer data sheet.
Typical applications include bridge-transducer signal conditioning, laboratory measurement front ends, programmable test equipment, industrial process monitoring, and multichannel data-acquisition systems. In a bridge or sensor interface, the selected gain can normalize a small sensor output before it reaches an ADC. The AD526BD can also serve as the first gain stage in a cascaded architecture, where two devices provide higher overall gain while retaining the same family architecture.
A key design consideration is signal settling after a gain-code change. Allow sufficient acquisition time for the amplifier and external anti-alias network to settle before sampling the converted signal. Keep sensitive analog traces short, place input and output bypass components close to the device, and use a clean ground reference to minimize errors that could otherwise appear as measurement gain errors rather than as noise from the source.
This product page combines the AD526 family architecture, gain-programming behavior, application guidance, and drop-in candidate analysis. It also provides practical selection criteria for engineers deciding between package, grade, temperature-range, and gain-configuration options for precision analog signal chains.
Drop-in alternatifler için AD526BD — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller AD526BD (aynı form faktörü ve ayağa oturma) — farklı olan Package, External Components Required, Operating Temperature Range, Supply Voltage Range.
AD526BDZ
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →AD526ADZ
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →AD526BD Maksimum Değerlendirmeler & Elektriksel Özellikler
| Product Type | Single-ended monolithic software-programmable gain amplifier |
| Number of Channels | 1 circuit |
| Programmable Gain | 1, 2, 4, 8, or 16 |
| Maximum Programmable Gain | 16 V/V |
| Two-Chip Cascade Maximum Gain | 256 V/V |
| Gain Error, C Grade | 0.01% max |
| Gain Error, A Grade | 0.02% max |
| Gain Drift Over Temperature | 0.5 ppm/°C |
| Control Input Compatibility | TTL-compatible latched inputs |
| External Gain-Setting Components | 0 components |
| Internal Resistor Network | Included |
| Signal Polarity | Single-ended |
| Paket | 16-CDIP |
| Lead Count | 16 leads |
| Montaj Türü | Through-hole |
AD526BD 16-cdip Pin Yapısı Kılavuzu
AD526BD (16-cdip paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: AD526BD.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
AD526BD için uygundur 6 uygulamas: Precision Sensor Signal Conditioning, Industrial Process Measurement, Laboratory Data Acquisition, Programmable Test and Measurement, Two-Chip High-Gain Cascade, Bridge Transducer Amplifier.
Precision Sensor Signal Conditioning
The AD526BD fits low-level sensor front ends because it offers 1, 2, 4, 8, and 16 gain settings while eliminating external gain-setting resistors. Position it between a transducer or bridge output and an ADC to normalize signals of different amplitudes into a usable converter range. Its integrated resistor network simplifies board layout, and the specified C-grade gain error of 0.01% maximum supports accurate measurements. When the source amplitude changes, update the latched gain code and allow the amplifier to settle before sampling. Check the AD526 input range, common-mode limits, bandwidth, and noise requirements against the particular sensor output.
Önerilen
Industrial Process Measurement
The AD526BD is useful in industrial process-monitoring systems where pressure, temperature, or flow sensors produce signals over a wide amplitude range. Its binary gains from 1 through 16 let one analog channel accommodate several input ranges without replacing external precision resistors. The 16-CDIP through-hole format also supports prototyping and repairable instrumentation assemblies. Keep the gain code stable during a measurement to avoid including switching transients in the sampled result. Validate the device against the sensor excitation scheme, industrial noise environment, and required measurement bandwidth before production release.
Önerilen
Laboratory Data Acquisition
The AD526BD fits laboratory data-acquisition front ends that need repeatable gain selection under digital control. With gains of 1, 2, 4, 8, and 16, it can attenuate larger channels relative to smaller ones while preserving one common amplifier topology. Its monolithic construction includes the amplifier and resistor network, reducing board space and avoiding external resistor matching. Use the latched inputs to command gain from a controller, then apply a settling delay before enabling the ADC conversion. The stated 0.01% maximum C-grade gain error and 0.5 ppm/°C drift provide useful starting points for uncertainty analysis.
Önerilen
Programmable Test and Measurement
The AD526BD can normalize varied input amplitudes in programmable test equipment because its gain code can be changed under logic control. A single board design may therefore cover several signal ranges without changing analog hardware. The 1-to-16 gain choices are especially useful when the source amplitude is known to vary by powers of two. For automated measurements, coordinate gain-code updates with acquisition timing so the amplifier reaches its new operating point before conversion. Confirm settling time and usable bandwidth in the Analog Devices data sheet for the required gain code and signal shape.
Önerilen
Two-Chip High-Gain Cascade
The AD526BD can participate in a two-chip cascade that extends the AD526 family's binary gain range to 256. This arrangement suits very small sensor outputs that cannot be brought into an ADC's useful range with one amplifier stage. The stages should be connected according to the AD526 manufacturer's cascade circuit, with attention to interstage loading, bandwidth, offset, and stability. As each gain code changes, both stages may require additional settling before the final sample is valid. Use the family data sheet as the authoritative basis for component values and signal-path layout.
Önerilen
Bridge Transducer Amplifier
The AD526BD is appropriate for bridge-transducer conditioning when the bridge output requires programmable amplification before digitization. Its binary gain choices allow a controller to compensate for different mechanical ranges, load conditions, or excitation levels while retaining a fixed analog gain network. The integrated resistor network avoids the need to match external precision gain components, and the 16-CDIP package simplifies through-hole assembly. Maintain a low-impedance reference return and follow the data sheet's input and ground recommendations. Verify that the selected gain preserves the bridge signal's common-mode range and bandwidth.
Önerilen
Mühendislik referans verileri: AD526BD — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | AD526BDZ | AD526ADZ |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-CDIP | 16-CDIP | 16-CDIP |
| Product Type | Software-programmable gain amplifier | Software-programmable gain amplifier | Software-programmable gain amplifier |
| Programmable Gain | 1, 2, 4, 8, or 16 | 1, 2, 4, 8, or 16 | 1, 2, 4, 8, or 16 |
| Maximum Single-Chip Gain | 16 | 16 | 16 |
| Two-Chip Cascade Gain | 256 | 256 | 256 |
| Gain Drift Over Temperature | 0.5 ppm/°C | 0.5 ppm/°C | 0.5 ppm/°C |
| Control Interface | TTL-compatible latched inputs | TTL-compatible latched inputs | TTL-compatible latched inputs |
| External Gain-Setting Components | 0 components | 0 components | 0 components |
Ana Farklılayıcılar
- Higher specified gain accuracy than the A-grade family option (karşılaştırma:AD526ADZ)
- Complete integrated gain network (karşılaştırma:AD526ADZ)
- High-gain cascade capability (karşılaştırma:AD526BDZ)
Tasarım Notları
Treat a gain-code transition as an acquisition boundary. Latch the new binary gain setting, allow the AD526BD and any downstream anti-alias filter to settle, and then initiate the ADC conversion. Sampling too early can make a gain transition appear as a signal excursion. Use the manufacturer settling-time data for the selected gain and signal bandwidth rather than assuming the previous conversion interval is sufficient.
Place the required bypass and compensation components close to their associated AD526BD pins, and route the analog input and output with minimal loop area. For the 16-CDIP implementation, provide adequate through-hole spacing and avoid routing high-current digital or switching-supply traces beneath the analog path. A clean ground connection is especially important because resistor-network gain accuracy alone does not remove errors caused by ground gradients or common-mode coupling.
Calculate the amplifier's approximate dissipation from the actual supply, output, quiescent current, and load-current conditions, then compare the resulting junction-temperature estimate with the limits in the AD526 data sheet. Use the formula P = (VIN - VOUT) × ILOAD plus device-specific internal losses. This calculation is an engineering estimate rather than a manufacturer maximum and must be checked against worst-case supply, load, and ambient temperature.
Uyumluluk Bilgisi
Compliance declarations for the exact AD526BD ordering code were not established by the listed manufacturer and distributor sources. Confirm current RoHS, REACH, lead-free, halogen-free, conflict-minerals, and automotive qualification documentation with Analog Devices before production release.