AD624AD/+ - Precision Instrumentation Amplifier | Analog Devices
MPN: AD624AD/+ ✓ AktifAD624AD/+ Genel Bakış
An instrumentation amplifier is a differential amplifier optimized for amplifying small voltage differences superimposed on larger common-mode voltages. Within the signal-chain hierarchy, it sits between the transducer and the analog signal-conditioning stage, providing differential input, high input impedance, stable closed-loop gain, and accurate gain-setting behavior. This makes the AD624AD/+ useful when the source resistance can vary or when a conventional difference amplifier would not provide sufficient common-mode rejection.
The AD624 achieves trimmed gains without external components at gain selections of 1, 100, 200, 500, and 1000. Its low-noise behavior, gain temperature coefficient of 5 ppm maximum at gain 1, input offset-voltage drift of 0.25 µV/°C maximum, and CMRR of 130 dB minimum at DC to 1000 Hz support accurate bridge measurements. Maximum nonlinearity is 0.001% at gain 200, helping preserve measurement integrity across the usable signal range.
For high-speed data-acquisition systems, the 25 MHz gain-bandwidth product permits signal amplification without sacrificing required bandwidth. The 5 V/µs slew rate supports rapid output transitions, while the 15 µs settling time defines useful settling behavior after a step input. These characteristics complement the precision dc specifications and make the amplifier suitable for both slow transducer measurements and higher-speed instrumentation.
Typical uses include load-cell weighing systems, strain-gauge bridges, pressure transducers, biomedical instrumentation, industrial process monitoring, and precision data-acquisition front ends. In a bridge circuit, the small differential output is amplified while common-mode excitation and environmental disturbances are rejected. The gain-selection network and the sensor bridge determine the usable sensitivity and should be evaluated together for offset, noise, saturation, and calibration requirements.
Designers should verify the complete AD624AD/+ pin assignment against the manufacturer datasheet before assigning PCB tracks. Supply bypassing, input grounding, bridge excitation return paths, and output settling time directly affect accuracy. Because the 16-lead ceramic DIP package is not represented by a pin-specific package diagram in the package library, use the manufacturer pin-description table for layout and inspection work.
This product page combines the manufacturer’s electrical characteristics with application guidance, drop-in-family comparisons, and practical design notes. It also distinguishes the AD624AD/+ from temperature-grade and package-code variants, helping engineers confirm ordering identity and PCB compatibility before committing a design to production.
Drop-in alternatifler için AD624AD/+ — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller AD624AD/+ (aynı form faktörü ve ayağa oturma) — farklı olan Package, Input Offset Voltage, Mounting Type, Settling Time, Slew Rate.
AD624ADZ
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →AD624BDZ
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →AD624CDZ
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →AD624AD/+ Maksimum Değerlendirmeler & Elektriksel Özellikler
| Product Type | High-precision, low-noise instrumentation amplifier |
| Number of Amplifiers | 1 circuit |
| Trimmed Gain Settings | 1, 100, 200, 500, and 1000 |
| Gain-Bandwidth Product | 25 MHz |
| Slew Rate | 5 V/µs |
| Settling Time | 15 µs |
| Besleme Gerilimi | 6 V to 18 V |
| Input Offset Voltage | 200 µV |
| Input Offset Voltage Drift | 0.25 µV/°C maximum |
| Common-Mode Rejection Ratio | 130 dB minimum from DC to 1000 Hz |
| Low Gain Temperature Coefficient | 5 ppm maximum at gain 1 |
| Nonlinearity | 0.001% maximum at gain 200 |
| Low-Frequency Noise | 0.2 V p-p at 10 Hz |
| Gain Programming | Pin-programmable |
| Paket | 16-lead ceramic DIP (CDIP) |
| Primary Transducer Applications | Load cells, strain gauges, and pressure transducers |
AD624AD/+ 16-lead ceramic dip (cdip) Pin Yapısı Kılavuzu
AD624AD/+ (16-lead ceramic dip (cdip) paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: AD624AD/+.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
AD624AD/+ için uygundur 6 uygulamas: Load-Cell Weighing Systems, Strain-Gauge Bridge Measurement, Pressure Transducer Signal Conditioning, Precision Data-Acquisition Front Ends, Medical and Biomedical Instrumentation, Industrial Process and Control Instrumentation.
Load-Cell Weighing Systems
The AD624AD/+ fits load-cell front ends where a small differential bridge signal must be amplified while excitation-related common-mode voltage is rejected. Its trimmed gains of 1, 100, 200, 500, and 1000 allow the amplifier to support several transducer sensitivities without external gain-setting components. The 130 dB minimum CMRR from DC to 1000 Hz and 0.25 µV/°C maximum input-offset drift are particularly useful when mechanical changes, temperature variation, or long cable runs could otherwise corrupt the measurement. In a practical weighing system, the amplifier sits between the bridge and the converter or controller, while a low-reference-voltage ADC preserves the amplified signal without allowing the amplifier to saturate.
Önerilen
Strain-Gauge Bridge Measurement
The AD624AD/+ is suitable for strain-gauge bridges that produce millivolt-level differential signals in the presence of a much larger excitation voltage. Its differential input and 130 dB minimum CMRR reduce the effect of common-mode variation, while the 25 MHz gain-bandwidth product provides more bandwidth than a purely slow precision-amplifier design. Gain can be selected at 1, 100, 200, 500, or 1000 without external resistors, simplifying calibration across different bridge sensitivities. Layout quality remains essential: keep bridge excitation current from sharing sensitive return paths with the amplifier ground, and follow the manufacturer application guidance for input filtering and supply decoupling.
Önerilen
Pressure Transducer Signal Conditioning
The AD624AD/+ can condition the low-level differential output of a resistive pressure transducer when both accuracy and response speed matter. The manufacturer’s maximum nonlinearity of 0.001% at gain 200 supports precise signal-chain budgeting, while the 5 V/µs slew rate and 15 µs settling time allow operation with faster pressure events than a low-bandwidth instrumentation amplifier would permit. Use the trimmed gain that produces useful ADC headroom without overdriving the output. The pressure bridge’s excitation voltage, source resistance, thermal drift, and shielding arrangement should be evaluated together because the amplifier cannot compensate for unstable bridge excitation or excessive common-mode input range.
Önerilen
Precision Data-Acquisition Front Ends
The AD624AD/+ works as an analog front end for precision data-acquisition systems that must recover small differential sensor signals before conversion. Its 25 MHz gain-bandwidth product supports a wider signal bandwidth than a slow dc-only amplifier, and the 15 µs settling time provides a defined basis for acquisition timing. Trimming the gain to 100, 200, 500, or 1000 increases the signal relative to downstream converter noise and quantization error. The system designer must still verify the output range, settling accuracy at the selected gain, common-mode limits, and sample-and-hold acquisition time of the following converter so that the complete chain preserves the amplifier’s precision.
Önerilen
Medical and Biomedical Instrumentation
The AD624AD/+ can amplify low-level physiological or diagnostic sensor signals when the system requires high common-mode rejection and low input-offset drift. The 0.25 µV/°C maximum drift specification helps maintain calibration stability as patient-sensor or ambient temperature changes, while the low-noise architecture supports extraction of small biopotential or bridge-derived signals. Its differential input is valuable when the source includes a large electrode or excitation common-mode voltage. Medical-system design must still include the required isolation, protection, leakage-current controls, input protection, and applicable product-safety validation; the amplifier’s electrical specifications alone do not establish compliance for the completed medical device.
Önerilen
Industrial Process and Control Instrumentation
The AD624AD/+ supports industrial process instrumentation where a sensor produces a small differential voltage and the surrounding equipment introduces substantial common-mode noise. Its 130 dB minimum CMRR from DC to 1000 Hz helps reject low-frequency process interference, and the trimmed gain options simplify scaling across pressure, force, and displacement sensors. The 25 MHz bandwidth can also accommodate higher-bandwidth control or monitoring signals. In an industrial enclosure, use careful grounding and shielding around the sensor leads, isolate high-current actuator wiring from the input path, and verify the input common-mode range. Proper thermal placement of the ceramic DIP and stable supply bypassing are necessary to preserve accuracy over changing plant environments.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: AD624AD/+ — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | AD624ADZ | AD624BDZ | AD624CDZ |
|---|---|---|---|---|
| Package | 16-lead ceramic DIP (CDIP) | 16-lead ceramic DIP (CDIP) | 16-lead ceramic DIP (CDIP) | 16-lead ceramic DIP (CDIP) |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Product Type | Precision instrumentation amplifier | Precision instrumentation amplifier | AD624-family instrumentation amplifier | AD624-family instrumentation amplifier |
| Number of Amplifiers | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Temperature Grade | AD grade; exact limits require confirmation | AD suffix grade | B suffix grade | C suffix grade |
Ana Farklılayıcılar
- Component-free trimmed gain selections (karşılaştırma:AD624ADZ)
- High bandwidth for precision instrumentation (karşılaştırma:AD624BDZ)
- Strong low-frequency common-mode rejection (karşılaştırma:AD624CDZ)
Tasarım Notları
Route the bridge excitation and sensitive input returns separately from high-current loads and digital switching paths. Keep the AD624AD/+ input and gain-control traces short, avoid large copper areas that can increase parasitic capacitance, and place the manufacturer-recommended bypass capacitors directly at the supply pins. For a DIP implementation, use a socket only when insertion, retention, and contamination requirements permit; otherwise, soldering the device can reduce vibration-induced contact resistance.
Account for the 25 MHz gain-bandwidth product when selecting the operating gain and the bandwidth required by the acquisition chain. A 15 µs settling-time specification is not equivalent to a complete ADC acquisition time, so verify converter aperture, sample-and-hold behavior, and the required amplitude accuracy. Gain-setting transitions should also be evaluated for output movement; a data-acquisition design may need sequencing or settling time between gain changes.
Do not treat the 130 dB CMRR figure as unlimited common-mode rejection or assume that every gain setting has identical dc and ac specifications. Confirm the full manufacturer electrical table for the selected gain, input common-mode range, output swing, and supply combination. Also verify that the bridge excitation remains within the amplifier’s allowable input range; insufficient headroom can clip the signal even when the differential measurement itself is small.
Uyumluluk Bilgisi
The manufacturer product page identifies the AD624 as a precision instrumentation amplifier, but the verified product information does not explicitly state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. The '+' ordering suffix should be confirmed against the manufacturer ordering information rather than assumed to encode a specific compliance declaration.