ADF4212BRUZ-RL7 - 2.7 GHz PLL Frequency Synthesizer | Analog Devices
MPN: ADF4212BRUZ-RL7 ✓ AktifADF4212BRUZ-RL7 Genel Bakış
A PLL, or phase-locked loop, is a feedback-controlled frequency-generation system. It compares a reference signal with a divided output signal, drives a voltage-controlled oscillator or VCO through a loop filter, and locks the output to the reference. The ADF4212 family provides programmable dual-modulus prescalers, programmable charge-pump currents, a 3-wire serial interface, lock detection, Fastlock operation, and a separate charge-pump supply for extended tuning-voltage range in 3 V systems.
Key features include RF and IF prescaler options of 8/9, 16/17, 32/33, and 64/65. The architecture supports RF synthesis up to 2.7 GHz and IF synthesis up to 1.0 GHz. Programmable charge-pump currents allow loop bandwidth and phase-noise performance to be adjusted with the external loop filter, while the 15-bit reference counter allows selectable reference frequencies at the phase-frequency detector input.
The ADF4212 is configured through a simple 3-wire serial interface. Analog and digital lock-detect functions provide status information for system control, and Fastlock mode can reduce acquisition time in frequency-hopping or rapidly retuned systems. A separate VP charge-pump supply allows the tuning-voltage headroom to be expanded when the main supply is only 3 V.
Typical uses include wireless receiver and transmitter local oscillators, RF up-conversion and down-conversion sections, IF signal chains, instrumentation, and frequency-generation modules. The 20-pin TSSOP package supports surface-mount PCB construction while keeping the design within a compact footprint.
For implementation, place the reference and charge-pump components close to the device and design the external loop filter for the intended phase-noise and lock-time requirements. Confirm prescaler, divider, charge-pump, and register settings against the application note and evaluate lock behavior across temperature and supply variation.
This product page combines the manufacturer product information, distributor package and ordering details, direct replacement candidates, and practical PLL design guidance to support component selection, PCB planning, and frequency-synthesizer implementation.
Drop-in alternatifler için ADF4212BRUZ-RL7 — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller ADF4212BRUZ-RL7 (aynı form faktörü ve ayağa oturma) — farklı olan Package.
ADF4212BRUZ-RL
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
ADF4212BRUZ
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →ADF4212BRUZ-RL7 Özellikler
| Product Type | Dual PLL clock and frequency synthesizer IC |
| Maximum RF Frequency | 2.7 GHz |
| Maximum IF Frequency | 1.0 GHz |
| Minimum RF Frequency | 0 MHz |
| Power Supply Voltage Range | 2.7 V to 5.5 V |
| Charge Pump Supply | Separate VP supply |
| RF Prescaler Ratios | 8/9, 16/17, 32/33, and 64/65 |
| IF Prescaler Ratios | 8/9, 16/17, 32/33, and 64/65 |
| Charge Pump Current | Programmable |
| Control Interface | 3-wire serial interface |
| Reference Counter | 15-bit |
| Lock Detection | Analog and digital |
| Acquisition Mode | Fastlock mode |
| Power-Down Mode | Supported |
| Pin Sayısı | 20 pins |
| Paket | 20-pin TSSOP, 4.40 mm width |
| Montaj Türü | Surface mount |
| İşletim Sıcaklığı Aralığı | -40 °C to +85 °C |
ADF4212BRUZ-RL7 20-pin tssop, 4.40 mm width Pin Yapısı Kılavuzu
ADF4212BRUZ-RL7 (20-pin tssop, 4.40 mm width paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: ADF4212BRUZ-RL7.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
ADF4212BRUZ-RL7 için uygundur 6 uygulamas: Wireless Transmitter Local Oscillator, Wireless Receiver Down-Conversion, RF Up-Conversion Local Oscillator, Frequency Instrumentation Signal Source, IF Signal-Chain Frequency Generation, Frequency-Hopping Communication System.
Wireless Transmitter Local Oscillator
The ADF4212BRUZ-RL7 fits a wireless transmitter local-oscillator stage because its RF synthesizer reaches 2.7 GHz and its programmable prescalers support multiple RF operating ratios. The 3-wire interface allows the transmitter controller to configure frequency-divider, prescaler, and charge-pump registers during channel changes. A separate VP supply can increase the tuning-voltage range of the external VCO, while Fastlock supports faster acquisition in frequency-hopping systems. The external loop filter and VCO must still be tuned for the target channel spacing, phase-noise limit, and lock-time requirement.
Önerilen
Wireless Receiver Down-Conversion
The ADF4212BRUZ-RL7 can generate receiver local-oscillator signals for RF down-conversion and separate IF synthesis. Its maximum RF frequency of 2.7 GHz and maximum IF frequency of 1.0 GHz cover common wireless conversion architectures, while programmable RF and IF prescalers provide design flexibility. Analog and digital lock outputs let the receiver firmware confirm lock before enabling signal processing. Board-level filtering, reference routing, and loop-filter layout remain essential for reliable phase noise and conversion performance.
Önerilen
RF Up-Conversion Local Oscillator
For RF up-conversion, the ADF4212BRUZ-RL7 supplies a programmable local-oscillator reference derived from a stable system reference. The 2.7 GHz maximum RF frequency supports transmit and mixer drive architectures in the supported operating range, while the 15-bit reference counter permits selectable reference frequencies at the phase-frequency detector input. The separate charge-pump supply is useful when the external VCO needs additional tuning range. Reference spurs and phase noise should be evaluated against the receiver sensitivity budget.
Önerilen
Frequency Instrumentation Signal Source
The ADF4212BRUZ-RL7 is suitable as the PLL core in a programmable frequency-source module where a single reference must generate an RF or IF output. Its programmable dividers, prescalers, charge-pump currents, and Fastlock mode provide the controls needed to balance resolution against acquisition time. The 20-pin TSSOP supports compact surface-mount assemblies, although the external reference buffer, loop filter, VCO, and output chain remain separate components. Firmware should verify lock after every frequency update and report faults through the digital lock signal.
Önerilen
IF Signal-Chain Frequency Generation
The ADF4212BRUZ-RL7's IF synthesizer can operate up to 1.0 GHz, making it appropriate for IF-generation blocks in receivers, transmitters, and test equipment. Independent RF and IF prescaler choices of 8/9, 16/17, 32/33, and 64/65 permit the divider architecture to be matched to the desired channel plan. Fastlock mode is useful when the system changes IF frequency frequently, while lock detection supports deterministic sequencing. Component selection for the loop filter and VCO should follow the required phase-noise, spur, and lock-time specifications.
Önerilen
Frequency-Hopping Communication System
The ADF4212BRUZ-RL7 fits frequency-hopping systems because Fastlock mode is designed to support faster lock acquisition when the synthesizer changes channels. Its 2.7 GHz RF range, programmable prescalers, and programmable charge-pump currents allow the acquisition behavior and tuning plan to be optimized. The 3-wire interface simplifies host control, and the analog or digital lock indication can gate transmission until the local oscillator is valid. Rapid hopping performance must be verified with the actual reference, VCO, loop filter, temperature range, and channel sequence.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: ADF4212BRUZ-RL7 — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | ADF4212BRUZ-RL | ADF4212BRUZ |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 20-pin TSSOP | 20-pin TSSOP - same | 20-pin TSSOP - same |
| Product Type | Dual PLL clock and frequency synthesizer IC | Dual PLL clock and frequency synthesizer IC | Dual PLL clock and frequency synthesizer IC |
| Maximum RF Frequency | 2.7 GHz | 2.7 GHz | 2.7 GHz |
| Maximum IF Frequency | 1.0 GHz | 1.0 GHz | 1.0 GHz |
| Power Supply Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Control Interface | 3-wire serial interface | 3-wire serial interface | 3-wire serial interface |
| Ordering Packing | -RL7 tape and reel | -RL tape and reel | Tube |
Ana Farklılayıcılar
- Higher RF tuning range within the identified drop-in set (karşılaştırma:ADF4208BRUZ)
- Production-oriented reel ordering option (karşılaştırma:ADF4212BRUZ)
- Direct same-family tape-and-reel alternative (karşılaştırma:ADF4212BRUZ-RL)
Tasarım Notları
Keep the reference input, charge-pump components, loop-filter network, and sensitive ground paths compact and physically separated from noisy switching nodes. Route the reference trace away from RF and digital return currents, use a continuous ground reference, and place the loop-filter components where their ground returns will not share high-current paths with the VCO or digital processor.
Coordinate the prescaler, N-divider, reference-counter, and charge-pump register values with the intended VCO range. A mismatched prescaler or divider program can produce an incorrect output frequency or prevent lock even though the reference and supplies are valid. After each frequency change, read the lock status and allow the loop to settle before enabling downstream circuitry.
Use the separate VP charge-pump supply to obtain the tuning-voltage range required by the external VCO, especially in 3 V systems. Confirm the maximum VP voltage against the Analog Devices electrical limits and design the regulator for low-noise operation. Decouple both the main supply and VP supply close to the device, and verify startup sequencing against the selected VCO and charge-pump configuration.
Uyumluluk Bilgisi
RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current Analog Devices product documentation or declaration. AEC-Q100 qualification is not applicable to this industrial-temperature PLL product.