ADF4212BRUZ-RL7 - 2.7 GHz PLL Frequency Synthesizer | Analog Devices
料号: ADF4212BRUZ-RL7 ✓ 量产中ADF4212BRUZ-RL7 概述
A PLL, or phase-locked loop, is a feedback-controlled frequency-generation system. It compares a reference signal with a divided output signal, drives a voltage-controlled oscillator or VCO through a loop filter, and locks the output to the reference. The ADF4212 family provides programmable dual-modulus prescalers, programmable charge-pump currents, a 3-wire serial interface, lock detection, Fastlock operation, and a separate charge-pump supply for extended tuning-voltage range in 3 V systems.
Key features include RF and IF prescaler options of 8/9, 16/17, 32/33, and 64/65. The architecture supports RF synthesis up to 2.7 GHz and IF synthesis up to 1.0 GHz. Programmable charge-pump currents allow loop bandwidth and phase-noise performance to be adjusted with the external loop filter, while the 15-bit reference counter allows selectable reference frequencies at the phase-frequency detector input.
The ADF4212 is configured through a simple 3-wire serial interface. Analog and digital lock-detect functions provide status information for system control, and Fastlock mode can reduce acquisition time in frequency-hopping or rapidly retuned systems. A separate VP charge-pump supply allows the tuning-voltage headroom to be expanded when the main supply is only 3 V.
Typical uses include wireless receiver and transmitter local oscillators, RF up-conversion and down-conversion sections, IF signal chains, instrumentation, and frequency-generation modules. The 20-pin TSSOP package supports surface-mount PCB construction while keeping the design within a compact footprint.
For implementation, place the reference and charge-pump components close to the device and design the external loop filter for the intended phase-noise and lock-time requirements. Confirm prescaler, divider, charge-pump, and register settings against the application note and evaluate lock behavior across temperature and supply variation.
This product page combines the manufacturer product information, distributor package and ordering details, direct replacement candidates, and practical PLL design guidance to support component selection, PCB planning, and frequency-synthesizer implementation.
直接替换替代料: ADF4212BRUZ-RL7 ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: ADF4212BRUZ-RL7 (相同外形与封装尺寸) ——差异在于 Package.
ADF4212BRUZ-RL
✅ 直接替换📋 参考替代料(不在目录中)
ADF4212BRUZ
✅ 直接替换联系询价
查看数据手册 →ADF4212BRUZ-RL7 规格参数
| Product Type | Dual PLL clock and frequency synthesizer IC |
| Maximum RF Frequency | 2.7 GHz |
| Maximum IF Frequency | 1.0 GHz |
| Minimum RF Frequency | 0 MHz |
| Power Supply Voltage Range | 2.7 V to 5.5 V |
| Charge Pump Supply | Separate VP supply |
| RF Prescaler Ratios | 8/9, 16/17, 32/33, and 64/65 |
| IF Prescaler Ratios | 8/9, 16/17, 32/33, and 64/65 |
| Charge Pump Current | Programmable |
| Control Interface | 3-wire serial interface |
| Reference Counter | 15-bit |
| Lock Detection | Analog and digital |
| Acquisition Mode | Fastlock mode |
| Power-Down Mode | Supported |
| 引脚数 | 20 pins |
| 封装 | 20-pin TSSOP, 4.40 mm width |
| 安装类型 | Surface mount |
| 工作温度范围 | -40 °C to +85 °C |
ADF4212BRUZ-RL7 20-pin tssop, 4.40 mm width 引脚配置指南
ADF4212BRUZ-RL7(20-pin tssop, 4.40 mm width 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: ADF4212BRUZ-RL7.
请参阅 数据手册 以查看完整引脚配置。
典型应用
ADF4212BRUZ-RL7 适用于 6 应用s: Wireless Transmitter Local Oscillator, Wireless Receiver Down-Conversion, RF Up-Conversion Local Oscillator, Frequency Instrumentation Signal Source, IF Signal-Chain Frequency Generation, Frequency-Hopping Communication System.
Wireless Transmitter Local Oscillator
The ADF4212BRUZ-RL7 fits a wireless transmitter local-oscillator stage because its RF synthesizer reaches 2.7 GHz and its programmable prescalers support multiple RF operating ratios. The 3-wire interface allows the transmitter controller to configure frequency-divider, prescaler, and charge-pump registers during channel changes. A separate VP supply can increase the tuning-voltage range of the external VCO, while Fastlock supports faster acquisition in frequency-hopping systems. The external loop filter and VCO must still be tuned for the target channel spacing, phase-noise limit, and lock-time requirement.
推荐
Wireless Receiver Down-Conversion
The ADF4212BRUZ-RL7 can generate receiver local-oscillator signals for RF down-conversion and separate IF synthesis. Its maximum RF frequency of 2.7 GHz and maximum IF frequency of 1.0 GHz cover common wireless conversion architectures, while programmable RF and IF prescalers provide design flexibility. Analog and digital lock outputs let the receiver firmware confirm lock before enabling signal processing. Board-level filtering, reference routing, and loop-filter layout remain essential for reliable phase noise and conversion performance.
推荐
RF Up-Conversion Local Oscillator
For RF up-conversion, the ADF4212BRUZ-RL7 supplies a programmable local-oscillator reference derived from a stable system reference. The 2.7 GHz maximum RF frequency supports transmit and mixer drive architectures in the supported operating range, while the 15-bit reference counter permits selectable reference frequencies at the phase-frequency detector input. The separate charge-pump supply is useful when the external VCO needs additional tuning range. Reference spurs and phase noise should be evaluated against the receiver sensitivity budget.
推荐
Frequency Instrumentation Signal Source
The ADF4212BRUZ-RL7 is suitable as the PLL core in a programmable frequency-source module where a single reference must generate an RF or IF output. Its programmable dividers, prescalers, charge-pump currents, and Fastlock mode provide the controls needed to balance resolution against acquisition time. The 20-pin TSSOP supports compact surface-mount assemblies, although the external reference buffer, loop filter, VCO, and output chain remain separate components. Firmware should verify lock after every frequency update and report faults through the digital lock signal.
推荐
IF Signal-Chain Frequency Generation
The ADF4212BRUZ-RL7's IF synthesizer can operate up to 1.0 GHz, making it appropriate for IF-generation blocks in receivers, transmitters, and test equipment. Independent RF and IF prescaler choices of 8/9, 16/17, 32/33, and 64/65 permit the divider architecture to be matched to the desired channel plan. Fastlock mode is useful when the system changes IF frequency frequently, while lock detection supports deterministic sequencing. Component selection for the loop filter and VCO should follow the required phase-noise, spur, and lock-time specifications.
推荐
Frequency-Hopping Communication System
The ADF4212BRUZ-RL7 fits frequency-hopping systems because Fastlock mode is designed to support faster lock acquisition when the synthesizer changes channels. Its 2.7 GHz RF range, programmable prescalers, and programmable charge-pump currents allow the acquisition behavior and tuning plan to be optimized. The 3-wire interface simplifies host control, and the analog or digital lock indication can gate transmission until the local oscillator is valid. Rapid hopping performance must be verified with the actual reference, VCO, loop filter, temperature range, and channel sequence.
推荐
推荐产品汇总
工程参考数据: ADF4212BRUZ-RL7 ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | ADF4212BRUZ-RL | ADF4212BRUZ |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 20-pin TSSOP | 20-pin TSSOP - same | 20-pin TSSOP - same |
| Product Type | Dual PLL clock and frequency synthesizer IC | Dual PLL clock and frequency synthesizer IC | Dual PLL clock and frequency synthesizer IC |
| Maximum RF Frequency | 2.7 GHz | 2.7 GHz | 2.7 GHz |
| Maximum IF Frequency | 1.0 GHz | 1.0 GHz | 1.0 GHz |
| Power Supply Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Control Interface | 3-wire serial interface | 3-wire serial interface | 3-wire serial interface |
| Ordering Packing | -RL7 tape and reel | -RL tape and reel | Tube |
关键差异点
- Higher RF tuning range within the identified drop-in set (对比 ADF4208BRUZ)
- Production-oriented reel ordering option (对比 ADF4212BRUZ)
- Direct same-family tape-and-reel alternative (对比 ADF4212BRUZ-RL)
设计说明
Keep the reference input, charge-pump components, loop-filter network, and sensitive ground paths compact and physically separated from noisy switching nodes. Route the reference trace away from RF and digital return currents, use a continuous ground reference, and place the loop-filter components where their ground returns will not share high-current paths with the VCO or digital processor.
Coordinate the prescaler, N-divider, reference-counter, and charge-pump register values with the intended VCO range. A mismatched prescaler or divider program can produce an incorrect output frequency or prevent lock even though the reference and supplies are valid. After each frequency change, read the lock status and allow the loop to settle before enabling downstream circuitry.
Use the separate VP charge-pump supply to obtain the tuning-voltage range required by the external VCO, especially in 3 V systems. Confirm the maximum VP voltage against the Analog Devices electrical limits and design the regulator for low-noise operation. Decouple both the main supply and VP supply close to the device, and verify startup sequencing against the selected VCO and charge-pump configuration.
合规信息
RoHS, REACH, lead-free, halogen-free, and conflict-minerals status require confirmation from the current Analog Devices product documentation or declaration. AEC-Q100 qualification is not applicable to this industrial-temperature PLL product.