KSZ8041TLI-S - 10/100 Ethernet PHY | Microchip | TQFP-48
MPN: KSZ8041TLI-S ✓ AktifKSZ8041TLI-S Genel Bakış
An Ethernet physical-layer transceiver, commonly called an Ethernet PHY, converts digital data into the electrical signaling used by 10BASE-T and 100BASE-TX networks. It belongs to the network interface controller and Ethernet transceiver hierarchy, operating between a network media-access controller and the transformer-coupled Ethernet line. The KSZ8041 supports MII, RMII, and SMII host interfaces, allowing integration with controllers operating in parallel, reduced-pin, or source-synchronous signaling configurations.
The principal benefits of the KSZ8041TLI-S are its 10/100 Mb/s dual-rate support, three digital host-interface choices, single-supply operation, and mixed-signal design. The manufacturer describes the mixed-signal implementation as extending signaling distance while reducing power consumption. Automatic MDI/MDI-X support also removes the need to configure transmit and receive pairs manually when either straight-through or crossover cabling is used.
The device integrates the analog PHY circuitry and digital host-interface functions required for a compact Ethernet front end. Its 48-pin TQFP-48 package provides separate interface and power-related connections on a conventional surface-mount footprint. Because it is a single transceiver, it does not by itself provide two independent copper ports, multi-port switching, or packet processing. Those functions belong to the network controller, switch, or higher-level system around the PHY.
Typical uses include embedded control systems, industrial automation equipment, communications modules, print systems, and compact network interfaces that require 10BASE-T or 100BASE-TX connectivity. The MII interface supports designs with a broad parallel signal set, RMII reduces host-side pin requirements, and SMII supports systems configured for source-synchronous signaling. Selection should account for the host controller's supported physical interface and the electrical requirements of the magnetic network interface.
Place the PHY, its supporting passive components, and the Ethernet magnetic device according to the manufacturer's reference layout. Keep high-speed host-interface traces short and controlled, provide the specified supply and decoupling arrangement, and account for magnetics and connector placement when defining the Ethernet channel. Verify signal integrity, return loss, insertion loss, and radiated emissions over the intended network interface before production release.
This page organizes the official product information, package details, replacement comparisons, interface selection guidance, and practical integration notes into one engineering-focused resource. It also distinguishes confirmed drop-in options from functional alternatives so that footprint, interface, and parameter compatibility can be checked before a PCB substitution is approved.
Drop-in alternatifler için KSZ8041TLI-S — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller KSZ8041TLI-S (aynı form faktörü ve ayağa oturma) — farklı olan Package, Device Type, Host Interface, Supply Architecture, Supported Data Rates.
KSZ8041TLI
✅ Yerleştirme✓ Stokta
$3.6094 / Birim
Veri Şablonunu Görüntüle →KSZ8041FTLI
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →KSZ8041TL
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →KSZ8041MLL
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →KSZ8041TLI-S Özellikler
| Device Type | 10BASE-T/100BASE-TX Ethernet physical-layer transceiver |
| Supported Data Rates | 10 Mb/s and 100 Mb/s |
| Supply Architecture | Single supply |
| Host Interface Options | MII, RMII, and SMII |
| Auto MDI/MDI-X | Supported |
| Process Technology | Low-power CMOS mixed-signal process |
| Ethernet Standard | IEEE 802.3u |
| Number of Transceivers | 1 |
| Paket | 48-pin TQFP, 7 x 7 mm |
| Montaj Türü | Surface mount |
| RoHS Durumu | Compliant |
| REACH Status | Compliant |
| Automotive Network Support | HP Auto MDI/MDI-X support |
KSZ8041TLI-S 48-pin tqfp, 7 x 7 mm Pin Yapısı Kılavuzu
KSZ8041TLI-S (48-pin tqfp, 7 x 7 mm paket) için pin yapısı. Pin numaralandırma, işlevleri ve bağlantı şemaları üretici veri kitapçığında tanımlanmıştır. Doğru ayak ve soldurma kılavuzları için onu referans alın.
Ayrıntılı pin çıkış verisi mevcut değil: KSZ8041TLI-S.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
KSZ8041TLI-S için uygundur 6 uygulamas: Embedded Ethernet Control Systems, Industrial Automation Equipment, Printers and Networked Peripherals, Communications Gateways, Networked Sensor and Monitoring Equipment, Communications and Networking Modules.
Embedded Ethernet Control Systems
The KSZ8041TLI-S fits embedded control systems that need a compact copper-Ethernet front end at 10 Mb/s or 100 Mb/s. Its MII interface supports a conventional parallel controller connection, while RMII offers a lower pin-count option for compact processors and programmable controllers. The single-supply architecture and 48-pin TQFP package simplify board planning compared with implementing discrete analog magnetics drivers and receivers. Its automatic MDI/MDI-X handling also lets the system operate with either straight-through or crossover cabling without a manual TX/RX pair configuration.
Önerilen
Industrial Automation Equipment
The KSZ8041TLI-S is appropriate for industrial automation controllers, sensor gateways, and remote I/O equipment requiring 10BASE-T or 100BASE-TX connectivity. The RMII interface can reduce host-side connections when the connected controller supports it, while MII provides a broadly established parallel interface. The manufacturer's mixed-signal design is intended to reduce power consumption and extend signaling distance, supporting compact industrial equipment where Ethernet replaces a more complex fieldbus. Final qualification should confirm the required temperature grade and operating-voltage limits.
Önerilen
Printers and Networked Peripherals
The KSZ8041TLI-S can provide the Ethernet physical layer in a network printer, scanner, or controller peripheral. A 100 Mb/s PHY supports faster transfers than a 10 Mb/s-only implementation while retaining support for legacy 10BASE-T links. The selectable MII, RMII, and SMII interfaces let the designer align the physical layer with the embedded host architecture. Automatic MDI/MDI-X operation simplifies installation by accommodating common straight-through and crossover cable conventions without manual pair swapping.
Önerilen
Communications Gateways
The KSZ8041TLI-S suits gateways that bridge a local embedded processor to a 10/100 Ethernet network. RMII is useful when minimizing host-side wiring is a priority, while MII offers a simple option for controllers with a dedicated parallel Ethernet interface. The PHY's single-port architecture suits a basic uplink rather than a managed multiport switch. Because the KSZ8041TLI-S handles physical-layer signaling only, the system designer must allocate MAC, protocol, security, and network-management functions to the host processor or companion controller.
Önerilen
Networked Sensor and Monitoring Equipment
The KSZ8041TLI-S can provide wired-network connectivity for environmental monitors, building controllers, and remote sensing nodes that need reliable 10BASE-T or 100BASE-TX operation. Its low-power mixed-signal implementation is relevant to energy-conscious embedded equipment, while automatic MDI/MDI-X improves installation flexibility. RMII may help minimize the host connection when the sensor controller includes that interface. The Ethernet channel still requires an appropriate magnetic device and careful layout to preserve signal integrity between the transceiver and connector.
Önerilen
Communications and Networking Modules
The KSZ8041TLI-S is suitable for compact communications modules that expose a 10/100 Ethernet port to a host processor or communication controller. Its three host-interface options allow the module designer to select RMII for pin reduction, MII for conventional parallel signaling, or SMII for a compatible source-synchronous architecture. The 7 x 7 mm TQFP package supports dense module construction without requiring a fine-pitch BGA footprint. Before layout release, follow the manufacturer reference placement for the PHY, decoupling, magnetic device, and Ethernet connector.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: KSZ8041TLI-S — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | KSZ8041TLI | KSZ8041FTLI | KSZ8041TL | KSZ8041MLL |
|---|---|---|---|---|---|
| Package | TQFP-48 (7 x 7 mm) | TQFP-48 (7 x 7 mm) | TQFP-48 (7 x 7 mm) | TQFP-48 (7 x 7 mm) | TQFP-48 (7 x 7 mm) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Device Type | 10BASE-T/100BASE-TX Ethernet PHY | 10BASE-T/100BASE-TX Ethernet PHY | 10BASE-T/100BASE-TX Ethernet PHY | 10BASE-T/100BASE-TX Ethernet PHY | 10BASE-T/100BASE-TX Ethernet PHY |
| Supported Data Rates | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s |
| Host Interfaces | MII, RMII, and SMII | MII, RMII, and SMII | MII, RMII, and SMII | MII, RMII, and SMII | MII, RMII, and SMII |
| Supply Architecture | Single supply | Single supply | Single supply | Single supply | Single supply |
| Auto MDI/MDI-X | Supported | Supported | Supported | Supported | Supported |
Ana Farklılayıcılar
- Three host-interface choices in one Ethernet PHY (karşılaştırma:KSZ8041TLI)
- Same-package reuse across KSZ8041 ordering variants (karşılaştırma:KSZ8041FTLI)
- Compact surface-mount implementation (karşılaştırma:KSZ8041MLL)
- Automatic copper-pair handling (karşılaştırma:KSZ8041TL)
Tasarım Notları
Use the manufacturer reference layout for the PHY, Ethernet magnetic device, and connector as one signal-chain structure. Preserve the specified component placement and keep the high-frequency analog network and digital host-interface sections organized according to the datasheet guidance. Place decoupling components at their designated power pins with short current paths. Confirm the final land pattern against the 48-pin TQFP drawing and the selected magnetic-device footprint before fabrication.
Validate the complete Ethernet channel from the KSZ8041TLI-S through the magnetic device to the RJ45 connector. Check insertion loss, return loss, impedance, isolation, and radiated emissions across the frequencies used by 10BASE-T and 100BASE-TX. Because the package contains both digital host signals and analog line-side circuitry, mismatched reference planes or long loops around the network interface can degrade performance even when the schematic is correct.
Do not select a replacement solely because its package is labeled TQFP-48. Confirm the ordered MPN, numbered pin assignments, operating-voltage limits, temperature range, Ethernet interface configuration, and regulatory requirements against the manufacturer documentation. The KSZ8041TLI, KSZ8041FTLI, KSZ8041TL, and KSZ8041MLL share the family footprint, but suffix-specific conditions can still affect production suitability. Document the engineering approval before changing the released BOM.
Follow the manufacturer's supply, decoupling, and power-sequencing recommendations exactly. The KSZ8041TLI-S uses a single-supply architecture, but the host controller, Ethernet magnetics, and PHY can still require coordinated rail sequencing during startup and shutdown. Test brownout behavior, rail ramp timing, and current consumption in the complete system rather than evaluating the PHY in isolation.
Uyumluluk Bilgisi
RoHS and REACH compliance are identified for the KSZ8041TLI-S and the compared KSZ8041TLI and KSZ8041FTLI variants. Automotive-grade qualification, lead-free construction, halogen-free status, and conflict-minerals status require confirmation for the exact selected ordering code.