MSP430F2112IPW - 16MHz 16-Bit MCU with 2KB Flash | Texas Instruments
MPN: MSP430F2112IPW ✓ AktifMSP430F2112IPW Genel Bakış
A mixed-signal microcontroller combines a microcontroller core, analog conversion, and communication peripherals into one device. The MSP430 family uses a 16-bit RISC CPU, 16-bit registers, and five low-power modes optimized for portable measurement. This architecture gives designers a compact platform for acquiring sensor data, controlling actuators, and communicating with a host or other embedded equipment.
The MSP430F2112IPW combines a 16 MHz maximum clock frequency with 2 KB of Flash and 256 B of SRAM. Its 10-bit ADC supports analog measurement, while the comparator supports threshold-based sensing. I2C, SPI, and UART interfaces provide flexible options for connecting sensors, displays, data loggers, and external converters without requiring separate interface devices.
The device belongs to the MSP430F2xx family and is built around a 16-bit RISC architecture with 16-bit registers. Its five low-power modes support a mixed operating strategy in which the MCU sleeps between measurements and wakes to process or transmit data. This is especially valuable in battery-operated instruments where average current, rather than peak processing speed, determines useful service life.
Typical uses include portable environmental monitors, compact industrial sensing nodes, digital thermometers, low-power data loggers, and battery-powered laboratory instruments. The combination of analog inputs and serial interfaces lets one controller handle a sensor, apply filtering or threshold logic, and forward results through a wired communications link.
PCB design should preserve analog signal quality and support the MCU's low-power behavior. Place the ADC input network and its ground reference away from high-current switching paths, route serial signals according to their expected edge rates, and follow the manufacturer datasheet for decoupling, exposed thermal considerations, and pin-specific functions.
This page combines device specifications, verified sourcing information, practical application guidance, and same-package replacement analysis. It also identifies the memory and peripheral trade-offs that engineers should review before migrating an existing MSP430 design.
Drop-in alternatifler için MSP430F2112IPW — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller MSP430F2112IPW (aynı form faktörü ve ayağa oturma) — farklı olan Flash Memory, Mounting Type, Package, SRAM, Comparator.
MSP430F2122IPW
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →MSP430F2111IPW
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
MSP430F2121IPW
✅ Yerleştirme ⚠️ Onaylanmamış ÖzelliklerFiyat için iletişime geçin
Veri Şablonunu Görüntüle →MSP430F1121IPW
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
MSP430G2253IPW28
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
MSP430F2112IPW Maksimum Değerlendirmeler & Elektriksel Özellikler
| CPU Architecture | 16-bit RISC |
| Register Width | 16 bit |
| Azami Saat Hızı | 16 MHz |
| Flash Memory | 2 KB |
| SRAM | 256 B |
| ADC Resolution | 10 bit |
| Comparator | 1 comparator |
| Serial Interfaces | I2C, SPI, and UART |
| Low-Power Modes | 5 modes |
| Besleme Gerilimi | 2.5 V or 3.3 V |
| Paket | 28-pin TSSOP |
| Package Width | 4.40 mm |
| Montaj Türü | Surface mount |
MSP430F2112IPW 4.40 mm Pin Yapısı Kılavuzu
MSP430F2112IPW (4.40 mm paket) için pin yapısı. Bu dijital IC, GPIO, iletişim arayüzleri (UART, SPI, I2C) ve güç pinleri içerir. Alternatif pin işlevleri ve yapılandırma seçenekleri için üretici veri kitapçığını referans alın. Tünel sistem tasarımı ve PCB yerleşimi için temel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: MSP430F2112IPW.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
MSP430F2112IPW için uygundur 6 uygulamas: Portable Environmental Monitor, Battery-Powered Data Logger, Digital Thermometer, Industrial Sensing Node, Low-Power Remote Controller, Battery-Powered Laboratory Instrument.
Portable Environmental Monitor
The MSP430F2112IPW fits portable environmental monitors that combine periodic sensing with low-power operation. Its 10-bit ADC can sample temperature, humidity, air-quality, or light signals, while the comparator can perform fast threshold detection without continuously running the CPU. The 16 MHz processor handles calibration, filtering, and status logic, and the 256 B of SRAM supports compact working buffers. I2C is suitable for compatible digital sensors, while UART or SPI can connect a host or external logger. Because the device provides five low-power modes, the firmware can sleep during sensor settling and wake for conversion and transmission. The principal design trade-off is the limited 2 KB of Flash, so application code, communication buffers, and update logic must be sized carefully.
Önerilen
Battery-Powered Data Logger
The MSP430F2112IPW is appropriate for battery-powered data loggers in which energy use and component count are primary constraints. Its 16-bit CPU can sample sensors, timestamp events, and update a local record without requiring a high-power application processor. The 2 KB of Flash is suitable for compact firmware, while the 256 B of SRAM can hold short acquisition windows or protocol buffers. The UART interface provides a straightforward connection to a serial storage or communications module, and the low-power modes permit long idle periods between measurements. System-level battery life depends on the sensor and interface loads as well as the MCU, so developers should measure average current across the complete operating cycle. Firmware should also prevent logging routines from exhausting the 2 KB code space.
Önerilen
Digital Thermometer
A compact digital thermometer can use the MSP430F2112IPW to combine analog sensing, threshold logic, and a serial readout. The 10-bit ADC is suitable for temperature-sensor outputs within the application's required accuracy, and the comparator can provide a simple over-temperature or set-point signal. A 16 MHz clock supports responsive display updates, calibration checks, and menu or interface handling without raising the device above the MSP430 family's low-power operating concept. I2C can connect a compatible display or temperature sensor, while UART can provide a wired output for test equipment. The 28-pin TSSOP package supports compact handheld products. Design effort should focus on sensor error, reference stability, and update latency, because those factors often determine thermometer accuracy more than CPU performance.
Önerilen
Industrial Sensing Node
The MSP430F2112IPW can serve as the local controller in a compact industrial sensing node that monitors an analog process signal and reports its status. Its 10-bit ADC and comparator provide analog acquisition and threshold functions, while I2C, SPI, and UART permit connection to sensors, local indicators, and a supervisory controller. The 16-bit RISC architecture and five low-power modes are useful in distributed systems where nodes operate intermittently on limited energy budgets. The 28-pin TSSOP package is practical for densely populated instrumentation, although industrial temperature qualification and EMC requirements must be checked against the exact product specification. Firmware should include input filtering, fault reporting, and communication retry logic while keeping code within the 2 KB Flash constraint.
Önerilen
Low-Power Remote Controller
The MSP430F2112IPW is well suited to a low-power remote controller that handles local user inputs, monitors an analog condition, and communicates with a central unit. The comparator can detect a threshold crossing, the ADC can quantify a sensor level, and the UART can provide a conventional command-and-response link. For a multi-wire or bus-based peripheral arrangement, I2C or SPI offers a more compact interface. Because the MCU supports five low-power modes, the controller can remain dormant until an input or sensor event occurs, reducing continuous energy consumption in remote installations. The 256 B of SRAM is adequate for modest protocol and control state, while the 2 KB Flash budget favors focused firmware. A production design should include watchdog-style recovery and defined behavior for communications loss.
Önerilen
Battery-Powered Laboratory Instrument
The MSP430F2112IPW can support a portable laboratory instrument that performs basic acquisition, control, and communication without a complex mixed-signal processor. The 10-bit ADC handles general-purpose analog measurements, the comparator provides fast limit detection, and the available serial interfaces support both low-speed sensors and service-port connectivity. Its 16 MHz CPU and 16-bit registers simplify arithmetic and state-machine development, while five low-power modes help control battery drain in bench instruments that spend much of their time idle. I2C and SPI suit higher-throughput peripherals, and UART supports simple terminal or service connections. The main constraint is memory: firmware, calibration coefficients, communication buffers, and logging code must fit within 2 KB of Flash and operate safely within 256 B of SRAM.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: MSP430F2112IPW — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | MSP430F2122IPW | MSP430F2111IPW | MSP430F2121IPW | MSP430F1121IPW | MSP430G2253IPW28 |
|---|---|---|---|---|---|---|
| Package | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP | 28-pin TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| CPU Architecture | 16-bit RISC MSP430F2xx | 16-bit RISC MSP430F21x2 | 16-bit RISC MSP430F21x1 | 16-bit RISC MSP430F21x1 | 16-bit MSP430F12x architecture | 16-bit MSP430G2x architecture |
| Software Porting Requirement | Baseline MSP430F2112 firmware | MSP430F21x2 port with peripheral and memory checks | MSP430F21x1 port with peripheral checks | MSP430F21x1 port with peripheral checks | Architecture migration and device-difference review | MSP430G2x firmware and peripheral migration |
Ana Farklılayıcılar
- Combines a 10-bit ADC, comparator, and three serial interfaces in one mixed-signal MCU (karşılaştırma:MSP430F1121IPW)
- Directly matches the low-power measurement role of the MSP430F21x2 family (karşılaştırma:MSP430G2253IPW28)
- Provides a direct family path without changing the 28-pin TSSOP footprint (karşılaştırma:MSP430F2111IPW)
- Supports three embedded serial protocols from one MCU (karşılaştırma:MSP430F2121IPW)
Tasarım Notları
Design the sleep-and-wake sequence around the complete measurement cycle rather than the MCU active current alone. Disable unused peripherals, configure unused pins appropriately, and place the device in the lowest mode that preserves the required wake behavior. Estimate average current from active current, standby current, wake duration, and sampling interval. Include the sensor, pull resistors, interface transceivers, regulator losses, and indicator currents because these loads can dominate the final battery-life result.
Route the ADC input and reference paths away from switching-regulator nodes, relay contacts, high-current LEDs, and other noisy sources. Keep the analog ground path compact and follow the manufacturer recommended decoupling arrangement for the supply pins. Place input and output bypass capacitors close to their corresponding pins, with the smallest capacitor nearest the package. Preserve a quiet analog island around the MCU when the PCB area permits, and use a solid ground-plane strategy without splitting return paths beneath digital interfaces.
Do not assume that equal TSSOP pin counts guarantee a drop-in replacement. Compare the actual signal assigned to every pin, alternate-function multiplexing, power pins, reset behavior, clock configuration, ADC channels, interrupt vectors, and timer resources. Texas Instruments migration guidance specifically warns that device differences can require attention even when pin compatibility is claimed. For any alternative, rebuild or validate the firmware, run communications and timing tests, and check the operating limits before releasing the PCB.
Give serial interfaces routing priority based on edge rate and topology. Keep I2C and UART signal paths continuous and away from antenna or switching-node copper, and use the ground plane as the primary return path. SPI clock lines should be short where possible, with the return path beneath the signal rather than split across a plane boundary. If external sensors communicate through long cables, add protection close to the connector so transient energy does not propagate into the controller.
The 2 KB Flash and 256 B SRAM limits require a deliberate firmware budget. Measure code size early, keep large lookup tables out of SRAM, and avoid allocating full protocol buffers when a streaming or byte-oriented approach will work. Include stack headroom for interrupt routines and avoid calling deeply nested functions from time-critical handlers. A modest memory-margin target helps prevent field failures caused by compiler changes, diagnostics, or later feature growth.
Uyumluluk Bilgisi
Request current manufacturer declarations for the exact MSP430F2112IPW ordering configuration before making a compliance claim. No verified cross-brand drop-in replacement was identified.