THS1230IDW - 12-Bit 30 MSPS Single-Channel ADC | Texas Instruments
MPN: THS1230IDW ✓ AktifTHS1230IDW Genel Bakış
An analog-to-digital converter, or ADC, converts a continuously varying analog voltage into a numeric value for processing, measurement, transmission, or control. The THS1230 belongs to the pipelined ADC family, whose multistage architecture supports high sampling rates while producing a parallel digital result. The single analog input and parallel 12-bit output place it between high-speed waveform conversion and lower-speed instrumentation, communications, or industrial signal-processing systems.
Key characteristics include 30 MSPS throughput, 12-bit resolution, one analog input, 3.3 V operation, and a -2 V to +2 V analog input range. The listed linearity error is 0.0488%. Its parallel interface exposes the conversion result through dedicated digital output pins, avoiding a serial-data link and allowing the converter to feed parallel logic, digital buses, or downstream processing stages when timing and interface requirements are compatible.
The device uses a proprietary pipelined conversion method and CMOS implementation. A 28-pin SOIC places the converter in a surface-mount package with gull-wing leads. Because the interface is parallel rather than serial, PCB routing requires multiple data traces and careful clock-to-data timing review. Designers should also evaluate analog input bandwidth, source impedance, settling behavior, clock jitter, reference accuracy, and output timing against the specific signal bandwidth before fixing the system sampling rate.
Typical uses include high-speed signal digitization, communications receivers, industrial monitoring, test and measurement equipment, control-loop sampling, and embedded systems that require 12-bit resolution at rates up to 30 MSPS. The 30 MSPS capability is particularly relevant when the input contains high-frequency content, provided that the analog front end limits bandwidth, preserves signal integrity, and supplies the converter with a suitably settled waveform.
A key design consideration is that a nominal 30 MSPS sampling rate does not guarantee useful full-scale bandwidth in every application. Keep analog traces short, use a controlled ground reference, place input and reference components close to their associated pins, and route the digital data bus away from sensitive analog nodes. Review clock jitter and acquisition timing whenever the source impedance or input frequency increases.
This page organizes the available electrical, packaging, lifecycle, sourcing, replacement, and application information for engineers evaluating the THS1230IDW. It also distinguishes verified drop-in alternatives from parts that require a different footprint, helping PCB and procurement decisions remain grounded in package, resolution, interface, and sampling-rate constraints.
Drop-in alternatifler için THS1230IDW — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
Bu Serideki Variantlar
Yedek parça uyumlu olan aynı serideki modeller THS1230IDW (aynı form faktörü ve ayağa oturma) — farklı olan Architecture, Operating Temperature, Package, Resolution, Number of Channels.
THS1230CDW
✅ YerleştirmeFiyat için iletişime geçin
Veri Şablonunu Görüntüle →THS1230IDW Maksimum Değerlendirmeler & Elektriksel Özellikler
| Converter Type | Pipelined ADC |
| Çözünürlük | 12 bit |
| Number of Channels | 1 channel |
| Number of Inputs | 1 input |
| Ölçekleme Oranı | 30 MSPS |
| Besleme Gerilimi | 3.3 V |
| Analog Input Range | -2 V to +2 V |
| Integral Linearity Error | 0.0488% |
| Output Interface | 12-bit parallel |
| Conversion Architecture | Proprietary method |
| Technology | CMOS |
| Paket | 28-pin SOIC |
| Package Code | PDSO28 |
| Terminal Count | 28 terminals |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| Temperature Grade | Industrial |
| Montaj Türü | Surface mount |
THS1230IDW rectangular Pin Yapısı Kılavuzu
THS1230IDW (rectangular paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: THS1230IDW.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
THS1230IDW için uygundur 6 uygulamas: Communications Receiver Signal Digitization, Industrial Process Monitoring, Test and Measurement Acquisition, Industrial Control Loop Sampling, Power and Motor Signal Monitoring, Embedded Parallel Data Acquisition.
Communications Receiver Signal Digitization
The THS1230IDW fits communications receiver designs that require rapid conversion into a parallel digital word. Its 12-bit resolution and 30 MSPS sampling rate provide 300 million sample points per second across a single analog channel, while the 3.3 V supply simplifies integration with contemporary digital logic. According to the manufacturer datasheet, the input range is -2 V to +2 V. The receiver should place appropriate gain and filtering ahead of the ADC, control clock jitter, and verify that the analog front end can drive the converter without introducing excessive settling error or distortion.
Önerilen
Industrial Process Monitoring
The THS1230IDW can digitize rapidly changing industrial sensor signals when deterministic sampling and a 12-bit parallel result are more useful than a low-speed serial interface. The 30 MSPS conversion capability provides ample timing margin for many monitoring channels after multiplexing, and the industrial temperature-grade designation supports use in demanding equipment. According to the manufacturer datasheet, the converter operates from 3.3 V with an analog input range of -2 V to +2 V. Protection, isolation, input conditioning, and grounding must be designed around the selected sensor and industrial environment.
Önerilen
Test and Measurement Acquisition
The THS1230IDW is suitable for compact test and measurement instruments that acquire a single analog waveform and process it through parallel digital logic or an FPGA. Its 12-bit resolution balances numerical detail against a 30 MSPS conversion rate, and the 28-pin SOIC package supports conventional surface-mount assembly. According to the manufacturer datasheet, the analog input range is -2 V to +2 V and the listed linearity error is 0.0488%. Instrument design should include calibration, stable references, input attenuation, bandwidth control, and a clock with low enough jitter for the target measurement accuracy.
Önerilen
Industrial Control Loop Sampling
The THS1230IDW can support high-speed control-loop sampling where a controller must observe a rapidly changing analog condition and retain the result as a 12-bit digital value. The 30 MSPS pipelined conversion rate provides substantially more sampling opportunities than slow-cycle acquisition systems, while parallel output can connect to a fast digital controller without relying on a serial protocol. According to the manufacturer datasheet, the device operates from 3.3 V. Designers must account for control-loop latency, anti-alias filtering, converter acquisition time, and the electrical limits of the selected processor interface.
Önerilen
Power and Motor Signal Monitoring
The THS1230IDW is applicable to laboratory or industrial systems that monitor power, current, or motor-control waveforms requiring rapid sampling. A single channel operating at up to 30 MSPS can capture transient behavior when the input network provides safe attenuation and the required bandwidth. According to the manufacturer datasheet, the converter accepts a -2 V to +2 V analog range and operates from 3.3 V. Protection components must handle the source voltage and transients, while layout should isolate the analog path from switching nodes and digital return currents.
Önerilen
Embedded Parallel Data Acquisition
The THS1230IDW fits embedded acquisition platforms that prefer direct parallel digital outputs over a serial converter interface. Twelve output bits can feed registers, shift stages, an FPGA, or a processor input bank, while the 30 MSPS rate supports rapid single-channel observations. According to the manufacturer datasheet, the part is a 28-pin SOIC device with a 3.3 V supply and a proprietary pipelined architecture. PCB planning should allocate routing for the parallel bus, provide solid decoupling, and verify timing margins for output data capture relative to the converter clock.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: THS1230IDW — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | THS1230CDW |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 28-pin SOIC | 28-pin SOIC |
| Resolution | 12 bit | 12 bit |
| Sampling Rate | 30 MSPS | 30 MSPS |
| Number of Channels | 1 channel | 1 channel |
| Output Interface | 12-bit parallel | 12-bit parallel |
Ana Farklılayıcılar
- Single-channel 30 MSPS throughput with 12-bit resolution (karşılaştırma:THS1230CDW)
- Industrial-grade ordering option (karşılaştırma:THS1230CDW)
- Direct parallel 12-bit result interface (karşılaştırma:THS1230CDW)
Tasarım Notları
Route the 12-bit parallel output as a controlled-length bus and place any output registers close enough to capture the converter's specified data timing. Keep switching supplies, clock routing, and fast digital return currents away from the analog input and reference nodes. Use a continuous ground plane and short analog traces to reduce coupling between the 30 MSPS conversion path and the parallel digital interface.
Verify the analog source impedance, acquisition time, input bandwidth, and conversion timing together before selecting a 30 MSPS operating condition. The input network should include appropriate attenuation or gain and antialias filtering. If the source has appreciable impedance, place the driver near the ADC rather than relying on trace length alone, because inadequate settling can create amplitude-dependent conversion error even when the sample clock is nominally accurate.
Do not treat the 30 MSPS conversion rate as a guaranteed usable input bandwidth. Assess clock jitter, analog bandwidth, reference noise, and the frequency content of the intended signal. Also confirm all 28 net assignments against the manufacturer pin-description table, particularly power, ground, analog input, clock, and control functions, before releasing a layout that assumes a generic 12-bit ADC pinout.
Uyumluluk Bilgisi
The component is an industrial-temperature-grade analog-to-digital converter, but no explicit RoHS, REACH, halogen-free, lead-free, conflict-minerals, or automotive-qualification declaration was present in the available product information.