THS1230IDW - 12-Bit 30 MSPS Single-Channel ADC | Texas Instruments
MPN: THS1230IDW ✓ فعالTHS1230IDW جائزہ
An analog-to-digital converter, or ADC, converts a continuously varying analog voltage into a numeric value for processing, measurement, transmission, or control. The THS1230 belongs to the pipelined ADC family, whose multistage architecture supports high sampling rates while producing a parallel digital result. The single analog input and parallel 12-bit output place it between high-speed waveform conversion and lower-speed instrumentation, communications, or industrial signal-processing systems.
Key characteristics include 30 MSPS throughput, 12-bit resolution, one analog input, 3.3 V operation, and a -2 V to +2 V analog input range. The listed linearity error is 0.0488%. Its parallel interface exposes the conversion result through dedicated digital output pins, avoiding a serial-data link and allowing the converter to feed parallel logic, digital buses, or downstream processing stages when timing and interface requirements are compatible.
The device uses a proprietary pipelined conversion method and CMOS implementation. A 28-pin SOIC places the converter in a surface-mount package with gull-wing leads. Because the interface is parallel rather than serial, PCB routing requires multiple data traces and careful clock-to-data timing review. Designers should also evaluate analog input bandwidth, source impedance, settling behavior, clock jitter, reference accuracy, and output timing against the specific signal bandwidth before fixing the system sampling rate.
Typical uses include high-speed signal digitization, communications receivers, industrial monitoring, test and measurement equipment, control-loop sampling, and embedded systems that require 12-bit resolution at rates up to 30 MSPS. The 30 MSPS capability is particularly relevant when the input contains high-frequency content, provided that the analog front end limits bandwidth, preserves signal integrity, and supplies the converter with a suitably settled waveform.
A key design consideration is that a nominal 30 MSPS sampling rate does not guarantee useful full-scale bandwidth in every application. Keep analog traces short, use a controlled ground reference, place input and reference components close to their associated pins, and route the digital data bus away from sensitive analog nodes. Review clock jitter and acquisition timing whenever the source impedance or input frequency increases.
This page organizes the available electrical, packaging, lifecycle, sourcing, replacement, and application information for engineers evaluating the THS1230IDW. It also distinguishes verified drop-in alternatives from parts that require a different footprint, helping PCB and procurement decisions remain grounded in package, resolution, interface, and sampling-rate constraints.
کے لیے ڈراپ اِن متبادل THS1230IDW — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں THS1230IDW (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Architecture, Operating Temperature, Package, Resolution, Number of Channels.
THS1230CDW
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →THS1230IDW زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Converter Type | Pipelined ADC |
| ریزولوشن | 12 bit |
| Number of Channels | 1 channel |
| Number of Inputs | 1 input |
| سیمپلنگ ریٹ | 30 MSPS |
| سپلائی وولٹیج | 3.3 V |
| Analog Input Range | -2 V to +2 V |
| Integral Linearity Error | 0.0488% |
| Output Interface | 12-bit parallel |
| Conversion Architecture | Proprietary method |
| Technology | CMOS |
| پیکیج | 28-pin SOIC |
| Package Code | PDSO28 |
| Terminal Count | 28 terminals |
| Terminal Form | Gull wing |
| Package Shape | Rectangular |
| Temperature Grade | Industrial |
| ماؤنٹنگ ٹائپ | Surface mount |
THS1230IDW rectangular پن کنفیگریشن گائیڈ
THS1230IDW (rectangular پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں THS1230IDW.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
THS1230IDW کے لیے موزوں ہے 6 ایپلیکیشنs: Communications Receiver Signal Digitization, Industrial Process Monitoring, Test and Measurement Acquisition, Industrial Control Loop Sampling, Power and Motor Signal Monitoring, Embedded Parallel Data Acquisition.
Communications Receiver Signal Digitization
The THS1230IDW fits communications receiver designs that require rapid conversion into a parallel digital word. Its 12-bit resolution and 30 MSPS sampling rate provide 300 million sample points per second across a single analog channel, while the 3.3 V supply simplifies integration with contemporary digital logic. According to the manufacturer datasheet, the input range is -2 V to +2 V. The receiver should place appropriate gain and filtering ahead of the ADC, control clock jitter, and verify that the analog front end can drive the converter without introducing excessive settling error or distortion.
تجویز کردہ
Industrial Process Monitoring
The THS1230IDW can digitize rapidly changing industrial sensor signals when deterministic sampling and a 12-bit parallel result are more useful than a low-speed serial interface. The 30 MSPS conversion capability provides ample timing margin for many monitoring channels after multiplexing, and the industrial temperature-grade designation supports use in demanding equipment. According to the manufacturer datasheet, the converter operates from 3.3 V with an analog input range of -2 V to +2 V. Protection, isolation, input conditioning, and grounding must be designed around the selected sensor and industrial environment.
تجویز کردہ
Test and Measurement Acquisition
The THS1230IDW is suitable for compact test and measurement instruments that acquire a single analog waveform and process it through parallel digital logic or an FPGA. Its 12-bit resolution balances numerical detail against a 30 MSPS conversion rate, and the 28-pin SOIC package supports conventional surface-mount assembly. According to the manufacturer datasheet, the analog input range is -2 V to +2 V and the listed linearity error is 0.0488%. Instrument design should include calibration, stable references, input attenuation, bandwidth control, and a clock with low enough jitter for the target measurement accuracy.
تجویز کردہ
Industrial Control Loop Sampling
The THS1230IDW can support high-speed control-loop sampling where a controller must observe a rapidly changing analog condition and retain the result as a 12-bit digital value. The 30 MSPS pipelined conversion rate provides substantially more sampling opportunities than slow-cycle acquisition systems, while parallel output can connect to a fast digital controller without relying on a serial protocol. According to the manufacturer datasheet, the device operates from 3.3 V. Designers must account for control-loop latency, anti-alias filtering, converter acquisition time, and the electrical limits of the selected processor interface.
تجویز کردہ
Power and Motor Signal Monitoring
The THS1230IDW is applicable to laboratory or industrial systems that monitor power, current, or motor-control waveforms requiring rapid sampling. A single channel operating at up to 30 MSPS can capture transient behavior when the input network provides safe attenuation and the required bandwidth. According to the manufacturer datasheet, the converter accepts a -2 V to +2 V analog range and operates from 3.3 V. Protection components must handle the source voltage and transients, while layout should isolate the analog path from switching nodes and digital return currents.
تجویز کردہ
Embedded Parallel Data Acquisition
The THS1230IDW fits embedded acquisition platforms that prefer direct parallel digital outputs over a serial converter interface. Twelve output bits can feed registers, shift stages, an FPGA, or a processor input bank, while the 30 MSPS rate supports rapid single-channel observations. According to the manufacturer datasheet, the part is a 28-pin SOIC device with a 3.3 V supply and a proprietary pipelined architecture. PCB planning should allocate routing for the parallel bus, provide solid decoupling, and verify timing margins for output data capture relative to the converter clock.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا THS1230IDW — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | THS1230CDW |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 28-pin SOIC | 28-pin SOIC |
| Resolution | 12 bit | 12 bit |
| Sampling Rate | 30 MSPS | 30 MSPS |
| Number of Channels | 1 channel | 1 channel |
| Output Interface | 12-bit parallel | 12-bit parallel |
اہم امتیازی خصوصیات
- Single-channel 30 MSPS throughput with 12-bit resolution (بمقابلہTHS1230CDW)
- Industrial-grade ordering option (بمقابلہTHS1230CDW)
- Direct parallel 12-bit result interface (بمقابلہTHS1230CDW)
ڈیزائن نوٹس
Route the 12-bit parallel output as a controlled-length bus and place any output registers close enough to capture the converter's specified data timing. Keep switching supplies, clock routing, and fast digital return currents away from the analog input and reference nodes. Use a continuous ground plane and short analog traces to reduce coupling between the 30 MSPS conversion path and the parallel digital interface.
Verify the analog source impedance, acquisition time, input bandwidth, and conversion timing together before selecting a 30 MSPS operating condition. The input network should include appropriate attenuation or gain and antialias filtering. If the source has appreciable impedance, place the driver near the ADC rather than relying on trace length alone, because inadequate settling can create amplitude-dependent conversion error even when the sample clock is nominally accurate.
Do not treat the 30 MSPS conversion rate as a guaranteed usable input bandwidth. Assess clock jitter, analog bandwidth, reference noise, and the frequency content of the intended signal. Also confirm all 28 net assignments against the manufacturer pin-description table, particularly power, ground, analog input, clock, and control functions, before releasing a layout that assumes a generic 12-bit ADC pinout.
تعمیل کی معلومات
The component is an industrial-temperature-grade analog-to-digital converter, but no explicit RoHS, REACH, halogen-free, lead-free, conflict-minerals, or automotive-qualification declaration was present in the available product information.