TLV2341IP - Low-Power CMOS Op Amp | Texas Instruments
MPN: TLV2341IP ✓ AktifTLV2341IP Genel Bakış
A CMOS operational amplifier is a voltage-controlled amplifier whose differential input produces an amplified output. The TLV2341 belongs to the broader operational-amplifier, analog-amplifier, and semiconductor hierarchy. Its low-voltage single-supply capability makes it useful for portable, remote, and battery-powered equipment, while its common-mode input range extends below the negative supply rail.
Key features include a wide 2 V to 8 V operating range, selectable 17 uA, 250 uA, or 1.5 mA supply current, and slew rates ranging from 0.02 V/us to 2.1 V/us at 3 V. The amplifier is especially suited to single-supply systems because it can process input signals near ground without requiring a bipolar supply. Characterized operation at 3 V and 5 V provides direct design support for common low-voltage rails.
The TLV2341 uses a rail-to-rail output architecture and supports single-supply operation. Its programmable supply current gives designers a practical trade-off between power consumption and dynamic performance. The 17 uA setting favors energy-limited instrumentation, while the 1.5 mA setting provides faster slewing for signal paths requiring larger bandwidth. The common-mode input range extends below the negative rail and to VDD minus 1 V at 25°C.
Typical applications include battery-powered sensor interfaces, low-power data-acquisition systems, portable instrumentation, industrial condition monitoring, and embedded analog signal conditioning. The device is also appropriate for systems that accept a negative supply rail or operate from a single low-voltage source. In each case, the selected supply-current mode should match the required bandwidth, noise, and power budget.
For PCB implementation, keep input and feedback routing short, provide stable bypass capacitance near the supply pins, and verify common-mode and output swing under the intended load. Because the device is available in an 8-pin PDIP package, insertion and socketed prototyping are straightforward, although surface-mount layouts require a separate package variant.
This product page combines manufacturer specifications, package information, application guidance, drop-in replacement analysis, and a parameter-by-parameter comparison. It also distinguishes programmable supply-current behavior from the fixed-current family options so engineers can select a pin-compatible device without overlooking electrical or layout trade-offs.
Drop-in alternatifler için TLV2341IP — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.
TLV2342IP
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
TLV2344IP
✅ Yerleştirme ⚠️ Onaylanmamış Özellikler📋 Katalogda Olmayan Referans Alternatifi
TLV2341IPW
✅ Yerleştirme📋 Katalogda Olmayan Referans Alternatifi
TLV2341IP Maksimum Değerlendirmeler & Elektriksel Özellikler
| Amplifier Type | Single-circuit operational amplifier |
| Supply Voltage Range | 2 V to 8 V |
| Characterized Supply Voltages | 3 V and 5 V |
| Selectable Supply Current | 17 uA, 250 uA, or 1.5 mA |
| Slew Rate | 0.02 V/us to 2.1 V/us at 3 V |
| Common-Mode Input Range | Extends below negative rail and to VDD - 1 V at 25°C |
| İşletim Sıcaklığı Aralığı | -40°C to 85°C |
| Paket | 8-pin PDIP |
| Montaj Türü | Through-hole |
| Number of Circuits | 1 circuit |
| Technology | CMOS |
| Supply Type | Single supply |
| Çıkış Türü | Rail-to-rail output |
TLV2341IP 8-pin pdip Pin Yapısı Kılavuzu
TLV2341IP (8-pin pdip paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.
Ayrıntılı pin çıkış verisi mevcut değil: TLV2341IP.
Aşağıdaki veri sayfası tam pin konfigürasyonu için.
Tipik Uygulamalar
TLV2341IP için uygundur 6 uygulamas: Battery-Powered Sensor Interfaces, Portable Data Acquisition, Remote Environmental Monitoring, Low-Power Instrumentation, Industrial Condition Monitoring, Ground-Referenced Signal Conditioning.
Battery-Powered Sensor Interfaces
The TLV2341IP fits low-power sensor conditioning because its supply current can be selected at 17 uA, 250 uA, or 1.5 mA while operating from 2 V to 8 V. According to the Texas Instruments product page, the corresponding slew rate spans 0.02 V/us to 2.1 V/us at 3 V. Place the amplifier near the sensor interface, use the lowest current mode that meets response requirements, and include local supply bypassing to reduce supply noise. The device's common-mode range extending below the negative rail is particularly useful for ground-referenced sensor outputs.
Önerilen
Portable Data Acquisition
The TLV2341IP supports portable data-acquisition systems where single-supply operation and adjustable power use are important. It operates across a 2 V to 8 V range and is characterized at 3 V and 5 V, making it suitable for systems powered from compact energy-storage cells. According to the manufacturer product page, its programmable supply current can be set to 17 uA, 250 uA, or 1.5 mA, allowing the design to trade amplifier speed for battery life. Use short analog input routes and stable feedback networks to preserve signal quality.
Önerilen
Remote Environmental Monitoring
The TLV2341IP is suited to remote environmental monitoring because it combines a 2 V to 8 V supply range with selectable low supply-current modes. According to the Texas Instruments product page, the 17 uA setting supports the lowest-power configuration, while 250 uA and 1.5 mA provide progressively greater dynamic capability. The common-mode input range extends below the negative rail, allowing direct conditioning of signals referenced to the lower supply rail. In field equipment, minimize leakage around the input pins and verify settling performance at the selected supply current.
Önerilen
Low-Power Instrumentation
The TLV2341IP can amplify low-level signals in compact test and measurement instruments without requiring a dual supply. Its 2 V to 8 V operating range and characterization at 3 V and 5 V simplify rail planning, while the selectable 17 uA, 250 uA, or 1.5 mA supply current supports different measurement modes. According to the Texas Instruments product page, the corresponding slew rate can range from 0.02 V/us to 2.1 V/us at 3 V. Choose the operating mode according to the required bandwidth and verify the output swing before full-scale inputs are applied.
Önerilen
Industrial Condition Monitoring
The TLV2341IP is appropriate for industrial condition-monitoring modules that require a compact, low-voltage analog amplifier. Its single-circuit 8-pin PDIP package supports straightforward through-hole assembly and prototyping, while the 2 V to 8 V supply range accommodates low-energy embedded systems. According to the Texas Instruments product page, the common-mode input range extends below the negative rail and to VDD minus 1 V at 25°C. Designers should still account for input overvoltage, transient protection, grounding, and the output limits of the selected operating mode.
Önerilen
Ground-Referenced Signal Conditioning
The TLV2341IP works well for conditioning signals that sit near ground because its common-mode input range extends below the negative supply rail. According to the Texas Instruments product page, the amplifier is optimized for single-supply applications and is fully specified at 3 V and 5 V. Select the appropriate 17 uA, 250 uA, or 1.5 mA supply-current setting based on the required slew rate, which can span 0.02 V/us to 2.1 V/us at 3 V. Maintain short feedback paths and avoid allowing the output to exceed its supply-dependent swing limits.
Önerilen
Önerilen Ürünler Özeti
Mühendislik referans verileri: TLV2341IP — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.
Seçim Kılavuzu
Alternatiflerle Karşılaştırma
| Parametre | Bu Ürün | TLV2342IP | TLV2344IP | TLV2341IPW |
|---|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP - same | 8-pin PDIP - same | 8-pin PDIP ordering-code match; verify physical package suffix |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Configuration | Single-circuit operational amplifier | Single-circuit operational amplifier | Single-circuit operational amplifier | Single-circuit CMOS amplifier |
Ana Farklılayıcılar
- Configurable operating-current range (karşılaştırma:TLV2342IP)
- Balance between ultra-low power and slew rate (karşılaştırma:TLV2344IP)
- Single-supply and ground-referenced input support (karşılaştırma:TLV2341IPW)
Tasarım Notları
Select the operating-current mode according to the system bandwidth instead of automatically using the fastest setting. The family supports 17 uA, 250 uA, and 1.5 mA supply current, with manufacturer-described slew rates from 0.02 V/us to 2.1 V/us at 3 V. For a remote or battery-powered design, begin at 17 uA and increase the current only if settling time and transient response fail the measurement requirement.
Place the supply bypass capacitor close to the positive and ground pins, and keep the non-inverting input, inverting input, and feedback components away from switching nodes and high-current paths. Although the PDIP package provides generous lead spacing, long analog traces still increase susceptibility to pickup and can reduce the benefit of the amplifier's low-noise operating modes. Maintain a compact ground return around the analog section.
Do not assume that the common-mode input range extends to the positive rail. According to the manufacturer product page, it extends below the negative rail and to VDD minus 1 V at 25°C, leaving limited headroom near the positive rail. Check both common-mode limits and output swing at the intended 3 V or 5 V supply, especially in sensor interfaces whose input can approach either rail.
Uyumluluk Bilgisi
No specific environmental or automotive compliance declaration was established for the TLV2341IP ordering code. Confirm the current material declaration with the manufacturer before release to production.