TLV2341IP - Low-Power CMOS Op Amp | Texas Instruments
料号: TLV2341IP ✓ 量产中TLV2341IP 概述
A CMOS operational amplifier is a voltage-controlled amplifier whose differential input produces an amplified output. The TLV2341 belongs to the broader operational-amplifier, analog-amplifier, and semiconductor hierarchy. Its low-voltage single-supply capability makes it useful for portable, remote, and battery-powered equipment, while its common-mode input range extends below the negative supply rail.
Key features include a wide 2 V to 8 V operating range, selectable 17 uA, 250 uA, or 1.5 mA supply current, and slew rates ranging from 0.02 V/us to 2.1 V/us at 3 V. The amplifier is especially suited to single-supply systems because it can process input signals near ground without requiring a bipolar supply. Characterized operation at 3 V and 5 V provides direct design support for common low-voltage rails.
The TLV2341 uses a rail-to-rail output architecture and supports single-supply operation. Its programmable supply current gives designers a practical trade-off between power consumption and dynamic performance. The 17 uA setting favors energy-limited instrumentation, while the 1.5 mA setting provides faster slewing for signal paths requiring larger bandwidth. The common-mode input range extends below the negative rail and to VDD minus 1 V at 25°C.
Typical applications include battery-powered sensor interfaces, low-power data-acquisition systems, portable instrumentation, industrial condition monitoring, and embedded analog signal conditioning. The device is also appropriate for systems that accept a negative supply rail or operate from a single low-voltage source. In each case, the selected supply-current mode should match the required bandwidth, noise, and power budget.
For PCB implementation, keep input and feedback routing short, provide stable bypass capacitance near the supply pins, and verify common-mode and output swing under the intended load. Because the device is available in an 8-pin PDIP package, insertion and socketed prototyping are straightforward, although surface-mount layouts require a separate package variant.
This product page combines manufacturer specifications, package information, application guidance, drop-in replacement analysis, and a parameter-by-parameter comparison. It also distinguishes programmable supply-current behavior from the fixed-current family options so engineers can select a pin-compatible device without overlooking electrical or layout trade-offs.
直接替换替代料: TLV2341IP ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
TLV2342IP
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TLV2344IP
✅ 直接替换 ⚠️ 规格未核验📋 参考替代料(不在目录中)
TLV2341IPW
✅ 直接替换📋 参考替代料(不在目录中)
TLV2341IP 最大额定值与电气特性
| Amplifier Type | Single-circuit operational amplifier |
| Supply Voltage Range | 2 V to 8 V |
| Characterized Supply Voltages | 3 V and 5 V |
| Selectable Supply Current | 17 uA, 250 uA, or 1.5 mA |
| Slew Rate | 0.02 V/us to 2.1 V/us at 3 V |
| Common-Mode Input Range | Extends below negative rail and to VDD - 1 V at 25°C |
| 工作温度范围 | -40°C to 85°C |
| 封装 | 8-pin PDIP |
| 安装类型 | Through-hole |
| Number of Circuits | 1 circuit |
| Technology | CMOS |
| Supply Type | Single supply |
| 输出类型 | Rail-to-rail output |
TLV2341IP 8-pin pdip 引脚配置指南
TLV2341IP(8-pin pdip 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: TLV2341IP.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TLV2341IP 适用于 6 应用s: Battery-Powered Sensor Interfaces, Portable Data Acquisition, Remote Environmental Monitoring, Low-Power Instrumentation, Industrial Condition Monitoring, Ground-Referenced Signal Conditioning.
Battery-Powered Sensor Interfaces
The TLV2341IP fits low-power sensor conditioning because its supply current can be selected at 17 uA, 250 uA, or 1.5 mA while operating from 2 V to 8 V. According to the Texas Instruments product page, the corresponding slew rate spans 0.02 V/us to 2.1 V/us at 3 V. Place the amplifier near the sensor interface, use the lowest current mode that meets response requirements, and include local supply bypassing to reduce supply noise. The device's common-mode range extending below the negative rail is particularly useful for ground-referenced sensor outputs.
推荐
Portable Data Acquisition
The TLV2341IP supports portable data-acquisition systems where single-supply operation and adjustable power use are important. It operates across a 2 V to 8 V range and is characterized at 3 V and 5 V, making it suitable for systems powered from compact energy-storage cells. According to the manufacturer product page, its programmable supply current can be set to 17 uA, 250 uA, or 1.5 mA, allowing the design to trade amplifier speed for battery life. Use short analog input routes and stable feedback networks to preserve signal quality.
推荐
Remote Environmental Monitoring
The TLV2341IP is suited to remote environmental monitoring because it combines a 2 V to 8 V supply range with selectable low supply-current modes. According to the Texas Instruments product page, the 17 uA setting supports the lowest-power configuration, while 250 uA and 1.5 mA provide progressively greater dynamic capability. The common-mode input range extends below the negative rail, allowing direct conditioning of signals referenced to the lower supply rail. In field equipment, minimize leakage around the input pins and verify settling performance at the selected supply current.
推荐
Low-Power Instrumentation
The TLV2341IP can amplify low-level signals in compact test and measurement instruments without requiring a dual supply. Its 2 V to 8 V operating range and characterization at 3 V and 5 V simplify rail planning, while the selectable 17 uA, 250 uA, or 1.5 mA supply current supports different measurement modes. According to the Texas Instruments product page, the corresponding slew rate can range from 0.02 V/us to 2.1 V/us at 3 V. Choose the operating mode according to the required bandwidth and verify the output swing before full-scale inputs are applied.
推荐
Industrial Condition Monitoring
The TLV2341IP is appropriate for industrial condition-monitoring modules that require a compact, low-voltage analog amplifier. Its single-circuit 8-pin PDIP package supports straightforward through-hole assembly and prototyping, while the 2 V to 8 V supply range accommodates low-energy embedded systems. According to the Texas Instruments product page, the common-mode input range extends below the negative rail and to VDD minus 1 V at 25°C. Designers should still account for input overvoltage, transient protection, grounding, and the output limits of the selected operating mode.
推荐
Ground-Referenced Signal Conditioning
The TLV2341IP works well for conditioning signals that sit near ground because its common-mode input range extends below the negative supply rail. According to the Texas Instruments product page, the amplifier is optimized for single-supply applications and is fully specified at 3 V and 5 V. Select the appropriate 17 uA, 250 uA, or 1.5 mA supply-current setting based on the required slew rate, which can span 0.02 V/us to 2.1 V/us at 3 V. Maintain short feedback paths and avoid allowing the output to exceed its supply-dependent swing limits.
推荐
推荐产品汇总
工程参考数据: TLV2341IP ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TLV2342IP | TLV2344IP | TLV2341IPW |
|---|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP - same | 8-pin PDIP - same | 8-pin PDIP ordering-code match; verify physical package suffix |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Amplifier Configuration | Single-circuit operational amplifier | Single-circuit operational amplifier | Single-circuit operational amplifier | Single-circuit CMOS amplifier |
关键差异点
- Configurable operating-current range (对比 TLV2342IP)
- Balance between ultra-low power and slew rate (对比 TLV2344IP)
- Single-supply and ground-referenced input support (对比 TLV2341IPW)
设计说明
Select the operating-current mode according to the system bandwidth instead of automatically using the fastest setting. The family supports 17 uA, 250 uA, and 1.5 mA supply current, with manufacturer-described slew rates from 0.02 V/us to 2.1 V/us at 3 V. For a remote or battery-powered design, begin at 17 uA and increase the current only if settling time and transient response fail the measurement requirement.
Place the supply bypass capacitor close to the positive and ground pins, and keep the non-inverting input, inverting input, and feedback components away from switching nodes and high-current paths. Although the PDIP package provides generous lead spacing, long analog traces still increase susceptibility to pickup and can reduce the benefit of the amplifier's low-noise operating modes. Maintain a compact ground return around the analog section.
Do not assume that the common-mode input range extends to the positive rail. According to the manufacturer product page, it extends below the negative rail and to VDD minus 1 V at 25°C, leaving limited headroom near the positive rail. Check both common-mode limits and output swing at the intended 3 V or 5 V supply, especially in sensor interfaces whose input can approach either rail.
合规信息
No specific environmental or automotive compliance declaration was established for the TLV2341IP ordering code. Confirm the current material declaration with the manufacturer before release to production.