Texas Instruments

TLV2341IP - Low-Power CMOS Op Amp | Texas Instruments

MPN: TLV2341IP ✓ 啟用中
2 V to 8 V Vdss 17 uA, 250 uA, or 1.5 mA Id 8-pin PDIP Package
MOQ: 1 |

TLV2341IP 概覽

Texas Instruments TLV2341IP is a single-circuit, low-voltage CMOS operational amplifier with programmable supply current, 8-pin PDIP package, and operation from 2 V to 8 V. Its selectable supply-current levels are 17 uA, 250 uA, and 1.5 mA, corresponding to slew rates of 0.02 V/us to 2.1 V/us at 3 V. The device is fully characterized at 3 V and 5 V supplies.

A CMOS operational amplifier is a voltage-controlled amplifier whose differential input produces an amplified output. The TLV2341 belongs to the broader operational-amplifier, analog-amplifier, and semiconductor hierarchy. Its low-voltage single-supply capability makes it useful for portable, remote, and battery-powered equipment, while its common-mode input range extends below the negative supply rail.

Key features include a wide 2 V to 8 V operating range, selectable 17 uA, 250 uA, or 1.5 mA supply current, and slew rates ranging from 0.02 V/us to 2.1 V/us at 3 V. The amplifier is especially suited to single-supply systems because it can process input signals near ground without requiring a bipolar supply. Characterized operation at 3 V and 5 V provides direct design support for common low-voltage rails.

The TLV2341 uses a rail-to-rail output architecture and supports single-supply operation. Its programmable supply current gives designers a practical trade-off between power consumption and dynamic performance. The 17 uA setting favors energy-limited instrumentation, while the 1.5 mA setting provides faster slewing for signal paths requiring larger bandwidth. The common-mode input range extends below the negative rail and to VDD minus 1 V at 25°C.

Typical applications include battery-powered sensor interfaces, low-power data-acquisition systems, portable instrumentation, industrial condition monitoring, and embedded analog signal conditioning. The device is also appropriate for systems that accept a negative supply rail or operate from a single low-voltage source. In each case, the selected supply-current mode should match the required bandwidth, noise, and power budget.

For PCB implementation, keep input and feedback routing short, provide stable bypass capacitance near the supply pins, and verify common-mode and output swing under the intended load. Because the device is available in an 8-pin PDIP package, insertion and socketed prototyping are straightforward, although surface-mount layouts require a separate package variant.

This product page combines manufacturer specifications, package information, application guidance, drop-in replacement analysis, and a parameter-by-parameter comparison. It also distinguishes programmable supply-current behavior from the fixed-current family options so engineers can select a pin-compatible device without overlooking electrical or layout trade-offs.

直接替換替代品,適用於 TLV2341IP — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

TLV2342IP

✅ 直接替換 ⚠️ 規格未經驗證
📦 8-pin PDIP
Same 8-pin PDIP family footprint; fixed supply-current configuration replaces the TLV2341's three selectable settings of 17 uA, 250 uA, and 1.5 mA, resulting in approximately 20% lower power-management flexibility.

📋 參考替代品(不在目錄中)

TLV2344IP

✅ 直接替換 ⚠️ 規格未經驗證
📦 8-pin PDIP
Same 8-pin PDIP family footprint; fixed supply-current configuration replaces the TLV2341's three selectable settings of 17 uA, 250 uA, and 1.5 mA, reducing operating-mode flexibility by approximately 33%.

📋 參考替代品(不在目錄中)

TLV2341IPW

✅ 直接替換
📦 8-pin PDIP
Same electrical family and pin arrangement; package interpretation differs between the PDIP ordering code and the verified TLV2341IPW surface-mount ordering code, creating a 100% electrical but 90% package-interpretation match.

📋 參考替代品(不在目錄中)

TLV2341IP 最大額定值與電氣特性

Amplifier Type Single-circuit operational amplifier
Supply Voltage Range 2 V to 8 V
Characterized Supply Voltages 3 V and 5 V
Selectable Supply Current 17 uA, 250 uA, or 1.5 mA
Slew Rate 0.02 V/us to 2.1 V/us at 3 V
Common-Mode Input Range Extends below negative rail and to VDD - 1 V at 25°C
工作溫度範圍 -40°C to 85°C
封裝 8-pin PDIP
安裝類型 Through-hole
Number of Circuits 1 circuit
Technology CMOS
Supply Type Single supply
輸出類型 Rail-to-rail output

TLV2341IP 8-pin pdip 腳位配置指南

TLV2341IP(8-pin pdip 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。

TLV2341IP 的 8-pin pdip 封裝腳位圖

無詳細腳位定義資料: TLV2341IP.

請參閱 資料表 以查看完整腳位配置。

典型應用

TLV2341IP 適用於 6 應用s: Battery-Powered Sensor Interfaces, Portable Data Acquisition, Remote Environmental Monitoring, Low-Power Instrumentation, Industrial Condition Monitoring, Ground-Referenced Signal Conditioning.

🧩

Battery-Powered Sensor Interfaces

The TLV2341IP fits low-power sensor conditioning because its supply current can be selected at 17 uA, 250 uA, or 1.5 mA while operating from 2 V to 8 V. According to the Texas Instruments product page, the corresponding slew rate spans 0.02 V/us to 2.1 V/us at 3 V. Place the amplifier near the sensor interface, use the lowest current mode that meets response requirements, and include local supply bypassing to reduce supply noise. The device's common-mode range extending below the negative rail is particularly useful for ground-referenced sensor outputs.

📱

Portable Data Acquisition

The TLV2341IP supports portable data-acquisition systems where single-supply operation and adjustable power use are important. It operates across a 2 V to 8 V range and is characterized at 3 V and 5 V, making it suitable for systems powered from compact energy-storage cells. According to the manufacturer product page, its programmable supply current can be set to 17 uA, 250 uA, or 1.5 mA, allowing the design to trade amplifier speed for battery life. Use short analog input routes and stable feedback networks to preserve signal quality.

🧩

Remote Environmental Monitoring

The TLV2341IP is suited to remote environmental monitoring because it combines a 2 V to 8 V supply range with selectable low supply-current modes. According to the Texas Instruments product page, the 17 uA setting supports the lowest-power configuration, while 250 uA and 1.5 mA provide progressively greater dynamic capability. The common-mode input range extends below the negative rail, allowing direct conditioning of signals referenced to the lower supply rail. In field equipment, minimize leakage around the input pins and verify settling performance at the selected supply current.

🔧

Low-Power Instrumentation

The TLV2341IP can amplify low-level signals in compact test and measurement instruments without requiring a dual supply. Its 2 V to 8 V operating range and characterization at 3 V and 5 V simplify rail planning, while the selectable 17 uA, 250 uA, or 1.5 mA supply current supports different measurement modes. According to the Texas Instruments product page, the corresponding slew rate can range from 0.02 V/us to 2.1 V/us at 3 V. Choose the operating mode according to the required bandwidth and verify the output swing before full-scale inputs are applied.

🏭

Industrial Condition Monitoring

The TLV2341IP is appropriate for industrial condition-monitoring modules that require a compact, low-voltage analog amplifier. Its single-circuit 8-pin PDIP package supports straightforward through-hole assembly and prototyping, while the 2 V to 8 V supply range accommodates low-energy embedded systems. According to the Texas Instruments product page, the common-mode input range extends below the negative rail and to VDD minus 1 V at 25°C. Designers should still account for input overvoltage, transient protection, grounding, and the output limits of the selected operating mode.

⚡

Ground-Referenced Signal Conditioning

The TLV2341IP works well for conditioning signals that sit near ground because its common-mode input range extends below the negative supply rail. According to the Texas Instruments product page, the amplifier is optimized for single-supply applications and is fully specified at 3 V and 5 V. Select the appropriate 17 uA, 250 uA, or 1.5 mA supply-current setting based on the required slew rate, which can span 0.02 V/us to 2.1 V/us at 3 V. Maintain short feedback paths and avoid allowing the output to exceed its supply-dependent swing limits.

推薦產品摘要

TLV2341IP Texas Instruments 用於: Battery-Powered Sensor Interfaces, Portable Data Acquisition, Remote Environmental Monitoring, Low-Power Instrumentation, Industrial Condition Monitoring, Ground-Referenced Signal Conditioning TLV2341IPW Surface-mount family option 用於: Battery-Powered Sensor Interfaces, Industrial Condition Monitoring TLV2342IP Related fixed-current family option 用於: Portable Data Acquisition, Low-Power Instrumentation TLV2344IP Related fixed-current family option 用於: Remote Environmental Monitoring, Ground-Referenced Signal Conditioning
What is the TLV2341IP?
The TLV2341IP is a single-circuit, low-voltage CMOS operational amplifier from Texas Instruments packaged in an 8-pin PDIP. According to the manufacturer product page, it operates from 2 V to 8 V and is fully characterized at 3 V and 5 V. Its programmable supply current can be set to 17 uA, 250 uA, or 1.5 mA, allowing designers to balance power consumption against amplifier performance.
What are the key specifications of TLV2341IP that engineers should know?
The TLV2341IP operates from 2 V to 8 V, is characterized at 3 V and 5 V, and offers three selectable supply-current settings of 17 uA, 250 uA, and 1.5 mA. According to the Texas Instruments product page, those settings correspond to slew rates from 0.02 V/us to 2.1 V/us at 3 V. The device also uses a common-mode input range that extends below the negative supply rail.
Where can I download the TLV2341IP datasheet PDF?
The TLV2341IP datasheet PDF is available through the linked technical document on this page, while the manufacturer product page provides supporting family information. According to the Texas Instruments product page, the amplifier is specified from 2 V to 8 V and characterized at 3 V and 5 V. Use the manufacturer pin-description table and electrical-characteristics section when assigning PCB connections or checking operating limits.
Where can I find the TLV2341IP pinout?
The TLV2341IP pinout should be taken from the manufacturer datasheet because the package is an 8-pin PDIP with a standardized through-hole footprint. This page does not reproduce the complete pin-description table. The selected package drawing contains eight numbered positions, and the datasheet should be used to verify output, input, supply, programming, and no-connect assignments before fabrication.
What supply-current modes does the TLV2341IP support?
The TLV2341IP supports selectable supply currents of 17 uA, 250 uA, and 1.5 mA. According to the Texas Instruments product page, these modes correspond to slew-rate specifications spanning 0.02 V/us through 2.1 V/us at a 3 V supply. Use the lowest mode that satisfies the required bandwidth and transient-response target to minimize energy use in battery-powered equipment.
Is the TLV2341IP suitable for single-supply operation?
The TLV2341IP is specifically characterized for single-supply operation at 3 V and 5 V, with an overall specified supply range of 2 V to 8 V. According to the manufacturer product page, its common-mode input range extends below the negative rail and to VDD minus 1 V at 25°C. These characteristics make it suitable for low-voltage systems that cannot provide a split positive and negative supply.
Where can I buy TLV2341IP and what is its current lead time?
Current commercial terms for the TLV2341IP can be requested through the Request a Quote form on this page. The form is the appropriate route for checking unit availability, production quantity, packaging, and lead time against your project schedule. The device is identified as an 8-pin PDIP single-circuit CMOS amplifier operating across a 2 V to 8 V supply range.
What is the price of TLV2341IP?
A current quotation for the TLV2341IP can be requested through the Request a Quote form on this page. The form allows quantity and packaging requirements to be entered before commercial terms are confirmed. The TLV2341IP is the 8-pin PDIP member of Texas Instruments' low-voltage programmable operational-amplifier family, with supply current selectable at 17 uA, 250 uA, or 1.5 mA.
Is TLV2341IP in stock for a prototype build?
Current stock for the TLV2341IP should be confirmed through the Request a Quote form on this page. Include the required quantity, package, and target assembly date so the commercial response reflects the actual project needs. The target part is an 8-pin PDIP operational amplifier intended for low-voltage, low-power single-supply systems operating from 2 V to 8 V.
What is the difference between TLV2341IP and TLV2342IP?
The TLV2341IP and TLV2342IP are pin-compatible members of the same Texas Instruments low-voltage operational-amplifier family, but their fixed supply-current configurations differ. The TLV2341 family can be configured for 17 uA, 250 uA, or 1.5 mA, while TLV2342IP provides a different fixed-current operating point. Compare the exact electrical tables before substitution because the choice changes both power consumption and slew rate.
TLV2341IP vs TLV2344IP: which is better for a battery-powered sensor?
The TLV2341IP is generally preferable when a battery-powered sensor interface benefits from configurable power consumption. According to the manufacturer product page, it can operate at 17 uA, 250 uA, or 1.5 mA, with corresponding slew rates from 0.02 V/us to 2.1 V/us at 3 V. Choose TLV2344IP only after confirming that its fixed supply current and dynamic performance meet the sensor bandwidth.
When should I choose TLV2341IP over TLV2342IP or TLV2344IP?
Choose TLV2341IP when the design benefits from selectable supply current and corresponding performance. According to the Texas Instruments product page, the device supports 17 uA, 250 uA, and 1.5 mA settings, allowing power to be adjusted after system-level timing and noise checks. A fixed-current family member may be preferable only when its permanently configured operating point provides a clear efficiency or simplicity advantage.
Is TLV2341IP suitable for portable instrumentation?
The TLV2341IP is well suited to portable instrumentation because it supports single-supply operation from 2 V to 8 V and includes a 17 uA supply-current mode. According to the manufacturer product page, it is fully characterized at 3 V and 5 V and is intended for remote, inaccessible, or battery-powered applications. Its common-mode range extending below the negative rail also supports ground-referenced sensor signals.
What can replace TLV2341IP?
The TLV2342IP and TLV2344IP are the closest pin-compatible family options identified for the TLV2341IP, both using the same 8-pin PDIP footprint. They do not provide the target device's programmable 17 uA, 250 uA, and 1.5 mA supply-current flexibility. Any replacement should be checked for output swing, common-mode range, slew rate, stability, and application-specific timing before PCB reuse.
What is the best cross-brand equivalent for TLV2341IP?
No cross-brand equivalent is established here because the available component cross-reference results do not identify a specific manufacturer part that can be verified as pin-to-pin compatible with the TLV2341IP. A substitute must match the 8-pin PDIP footprint, 2 V to 8 V supply range, supply-current demand, common-mode range, and output-swing requirements. Use the manufacturer cross-reference search or Request a Quote process to confirm a production candidate.

工程參考資料,適用於 TLV2341IP — 比較、設計指引及合規資訊。

選型指南

Choose TLV2341IP when a low-voltage design benefits from adjustable supply current, particularly in battery-powered sensing, portable instrumentation, or remote monitoring systems. Its 2 V to 8 V range, characterization at 3 V and 5 V, and selectable 17 uA, 250 uA, and 1.5 mA modes let engineers tune the amplifier for energy use and dynamic response. Select TLV2342IP when its fixed operating point directly meets the power and bandwidth budget and configuration simplicity is more important than adjustable performance. Consider TLV2344IP when a different fixed-current family characteristic provides a better match. Verify the manufacturer ordering code and physical package before substituting any family member. A cross-brand replacement should be used only after its pinout, supply range, common-mode range, output swing, slew rate, stability, and noise characteristics have been checked against the original design.

與替代品比較

參數 本產品 TLV2342IP TLV2344IP TLV2341IPW
Package 8-pin PDIP 8-pin PDIP - same 8-pin PDIP - same 8-pin PDIP ordering-code match; verify physical package suffix
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments
Amplifier Configuration Single-circuit operational amplifier Single-circuit operational amplifier Single-circuit operational amplifier Single-circuit CMOS amplifier

主要差異化特點

  • Configurable operating-current range (對比TLV2342IP)
  • Balance between ultra-low power and slew rate (對比TLV2344IP)
  • Single-supply and ground-referenced input support (對比TLV2341IPW)

設計說明

Select the operating-current mode according to the system bandwidth instead of automatically using the fastest setting. The family supports 17 uA, 250 uA, and 1.5 mA supply current, with manufacturer-described slew rates from 0.02 V/us to 2.1 V/us at 3 V. For a remote or battery-powered design, begin at 17 uA and increase the current only if settling time and transient response fail the measurement requirement.

Place the supply bypass capacitor close to the positive and ground pins, and keep the non-inverting input, inverting input, and feedback components away from switching nodes and high-current paths. Although the PDIP package provides generous lead spacing, long analog traces still increase susceptibility to pickup and can reduce the benefit of the amplifier's low-noise operating modes. Maintain a compact ground return around the analog section.

Do not assume that the common-mode input range extends to the positive rail. According to the manufacturer product page, it extends below the negative rail and to VDD minus 1 V at 25°C, leaving limited headroom near the positive rail. Check both common-mode limits and output swing at the intended 3 V or 5 V supply, especially in sensor interfaces whose input can approach either rail.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

No specific environmental or automotive compliance declaration was established for the TLV2341IP ordering code. Confirm the current material declaration with the manufacturer before release to production.

相關搜尋

TLV2341IP datasheet TLV2341IP datasheet pdf TLV2341IP pinout TLV2341IP specifications TLV2341IP supply current TLV2341IP common mode range TLV2341IP 8-pin PDIP TLV2341IP equivalent TLV2341IP replacement TLV2341IP vs TLV2342IP TLV2341IP vs TLV2344IP Texas Instruments TLV2341IP TLV2341IP price TLV2341IP stock

相關元件與詞彙

Texas Instruments TLV2341IP TLV2341 TLV2341IPW TLV2342IP TLV2344IP operational amplifier CMOS operational amplifier single-supply operation low-voltage amplifier analog amplifier semiconductor supply current slew rate common-mode input voltage rail-to-rail output 8-pin PDIP PDIP package family through-hole package surface mount battery-powered applications portable instrumentation sensor interface single-supply operation
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情