STMicroelectronics

TS974IYD - 12MHz Quad Rail-to-Rail Op Amp | STMicroelectronics

MPN: TS974IYD ✓ Aktif
2.7 V to 10 V Vdss 100 mA Id 14-SOIC, 3.90 mm body width Package
MOQ: 1 |

TS974IYD Genel Bakış

The STMicroelectronics TS974IYD is a four-circuit, general-purpose operational amplifier with rail-to-rail output swing, 12 MHz gain-bandwidth product, 60 dB common-mode rejection, and a 14-SOIC package. It accepts a 2.7 V to 10 V single-supply range or dual-supply operation from ±1.35 V to ±5 V, with a nominal 5 V single-supply configuration identified for the device.

An operational amplifier is an analog signal-conditioning IC that compares an input voltage with a feedback-defined reference and amplifies the resulting error voltage. The TS974 belongs to the rail-to-rail operational amplifier hierarchy, where the output can approach the supply rails. This characteristic is useful when the available signal range is small, while its low-noise and low-distortion behavior make the TS97x family suitable for audio preamplification and portable instrumentation.

The TS974IYD combines four amplifiers in one 14-SOIC package. Each channel has a gain-bandwidth product of 12 MHz and supports up to 100 mA of output current. Its 60 dB common-mode rejection ratio improves immunity to common-mode voltage on the input pair, while the 200 nA input bias current and 1 µA quiescent current per channel suit low-power circuitry. These characteristics support portable and battery-powered equipment operating from low supply voltages.

The device supports both single- and dual-supply arrangements. In a single-supply system, the input and output signal range requires attention near the rails even though the output stage has rail-to-rail swing. In a dual-supply circuit, the stated operating range extends from ±1.35 V to ±5 V. Because the TS974 is intended for low-noise amplification, resistor selection, decoupling, grounding, and output-load compatibility remain central to achieving the intended signal quality.

Typical uses include portable audio preamplification, low-level sensor conditioning, battery-powered measurement equipment, active filters, and general-purpose analog signal processing. Four channels in one package also reduce board area when a system needs several similar gain stages. The package pin arrangement and electrical characteristics must be checked against the manufacturer datasheet before applying it to a new board or using it as a replacement.

For a new design, begin with the required signal bandwidth, output swing, supply voltage, and load current. Place the bypass capacitor near the power pins, keep feedback loops compact, and verify that input common-mode and output swing requirements remain valid at the chosen gain. For an existing PCB, confirm the 14-SOIC footprint, pin functions, and electrical limits before substituting another amplifier.

This page consolidates the available manufacturer-family information, distributor listing details, ordering guidance, and drop-in comparison considerations. It is designed to help engineers identify whether the TS974IYD fits a low-voltage, low-noise quad-op-amp design before moving to detailed circuit review and datasheet verification.

Drop-in alternatifler için TS974IYD — aynı paket, pin-başına uyumlu. PCB yeniden montajı gerektiren farklı paket bileşenleri dışlanmıştır.

Bu Serideki Variantlar

Yedek parça uyumlu olan aynı serideki modeller TS974IYD (aynı form faktörü ve ayağa oturma) — farklı olan Package.

STMicroelectronics
Package: 14-pin SO package
İle Karşılaştır TS974IYD →

TS974IDT

✅ Yerleştirme ⚠️ Onaylanmamış Özellikler
STMicroelectronics
📦 14-SOIC
General-purpose operational amplifier · 4 circuits · Yes · 12 MHz · 4 V/us · 4 nV/Hz · 0.003% · ±1.35 V

Fiyat için iletişime geçin

Veri Şablonunu Görüntüle →

TS974IYD Maksimum Değerlendirmeler & Elektriksel Özellikler

Number of Amplifier Channels 4 circuits
Amplifier Type General-purpose operational amplifier
Output Swing Rail-to-rail
Gain-Bandwidth Product 12 MHz
Output Current per Channel 100 mA
Input Bias Current 200 nA
Common-Mode Rejection Ratio 60 dB
Quiescent Current per Channel 1 µA
Single-Supply Voltage Range 2.7 V to 10 V
Nominal Single-Supply Voltage 5 V
Dual-Supply Voltage Range ±1.35 V to ±5 V
Paket 14-SOIC, 3.90 mm body width
Total Pin Count 14 pins

TS974IYD 14-soic, 3.90 mm body width Pin Yapısı Kılavuzu

TS974IYD (14-soic, 3.90 mm body width paket) için pin yapısı. Bu analog bileşen, giriş, çıkış ve güç besleme pinleri içerir. Ofset null, telafi ve etkinleştirme pin yapılandırmaları için üretici veri kitapçığını referans alın. Sinyal işleme ve güç amplifikasyon devreleri için mükemmel bir bileşendir.

14-soic, 3.90 mm body width paket pin çizelgesi için TS974IYD

Ayrıntılı pin çıkış verisi mevcut değil: TS974IYD.

Aşağıdaki veri sayfası tam pin konfigürasyonu için.

Tipik Uygulamalar

TS974IYD için uygundur 6 uygulamas: Portable Audio Preamplification, Battery-Powered Sensor Conditioning, Low-Noise Active Filters, Low-Voltage Signal Buffers, Battery-Supplied Measurement Equipment, General-Purpose Analog Signal Processing.

🎧

Portable Audio Preamplification

The TS974IYD is well suited to portable audio preamplification because the STMicroelectronics TS97x family combines very low noise, low distortion, and rail-to-rail output swing. Its 12 MHz gain-bandwidth product gives each channel ample bandwidth for common audio signal paths, while the 1 µA quiescent current per channel helps limit consumption in battery-operated equipment. Four amplifiers in one 14-SOIC package can implement successive gain stages, buffers, or active filtering without requiring four separate packages. Confirm the output swing into the intended load and ensure that the input signal remains inside the amplifier's common-mode range.

🧩

Battery-Powered Sensor Conditioning

The TS974IYD fits low-voltage sensor conditioning where low bias current and low standby consumption are important. Its 200 nA input bias current reduces loading on high-impedance sensors, while 1 µA quiescent current per channel supports battery life. The 60 dB common-mode rejection ratio helps reduce the effect of common-mode noise on differential measurements, and the 12 MHz bandwidth supports signals beyond static sensor outputs. Engineers should still verify input offset, noise density, common-mode limits, and the sensor's full-scale output against the complete STMicroelectronics electrical tables.

🔧

Low-Noise Active Filters

The TS974IYD can implement multiple active-filter stages because it provides four general-purpose amplifiers in a 14-SOIC package. Its 12 MHz gain-bandwidth product and rail-to-rail output capability are useful for low-frequency filters with signal levels that benefit from reduced clipping near the supply rails. Very low noise and low distortion make the device relevant to audio and precision signal-conditioning networks. Component tolerances, gain-bandwidth behavior, output loading, and stability at the selected closed-loop gain should be evaluated before production. The 100 mA per-channel output-current listing also requires a load check.

⚡

Low-Voltage Signal Buffers

The TS974IYD can provide voltage buffering when a sensor or divider produces a signal that must drive another circuit without additional loading. Rail-to-rail output swing increases usable signal range in compact 2.7 V to 10 V systems, and four channels allow several buffers to share one package. Low quiescent current of 1 µA per channel is valuable in portable equipment, while 12 MHz bandwidth supports responsive signal paths. Use unity-gain stability information, verify the capacitive-load limits, and keep feedback routing short so the buffer preserves signal integrity.

📱

Battery-Supplied Measurement Equipment

The TS974IYD suits portable measurement equipment that needs several low-power analog channels. A single 14-SOIC package provides four amplifiers for transducer conditioning, gain adjustment, filtering, and output buffering. The low 1 µA quiescent current per channel helps conserve battery capacity, while operation from 2.7 V to 10 V supports cells, regulated rails, and dual-supply circuits down to ±1.35 V. The 60 dB common-mode rejection ratio is valuable when long sensor leads or switching converters introduce common-mode disturbance. Validate offset voltage, noise, input range, and calibration drift for the required measurement accuracy.

🏭

General-Purpose Analog Signal Processing

The TS974IYD is a practical quad-amplifier building block for general-purpose analog signal processing such as gain stages, comparators, integrators, and current-to-voltage converters. Its 12 MHz gain-bandwidth product supports a broad range of low-frequency and moderate-frequency tasks, while 200 nA input bias current reduces disturbance in high-impedance circuits. The 100 mA output current per channel provides headroom for conventional signal loads. Rail-to-rail output swing is advantageous in compact systems, but the designer must avoid relying on rail-to-rail input behavior unless it is explicitly confirmed in the complete electrical characteristics.

What is the operating voltage of TS974IYD?
The TS974IYD operates from 2.7 V to 10 V in a single-supply configuration and from ±1.35 V to ±5 V in a dual-supply configuration. According to the STMicroelectronics TS97x family datasheet, the family operates with voltages as low as ±1.35 V and provides rail-to-rail output swing. A 5 V single supply is also identified for this device, making it suitable for low-voltage portable systems.
What are the key specifications of TS974IYD that engineers should know?
The TS974IYD is a four-channel general-purpose operational amplifier with a 12 MHz gain-bandwidth product, 60 dB common-mode rejection ratio, 100 mA output current per channel, 200 nA input bias current, and 1 µA quiescent current per channel. The STMicroelectronics family information identifies rail-to-rail output swing, a 2.7 V to 10 V single-supply range, and a 14-SOIC package.
Where can I download the TS974IYD datasheet PDF?
The TS974IYD datasheet PDF is available through the STMicroelectronics family document hosted on Datasheets.com. The document covers the TS97x operational-amplifier family, including its ±1.35 V minimum dual-supply operation, rail-to-rail output swing, low-noise characteristics, and low-distortion performance. Use the manufacturer document for final pin assignments, test conditions, absolute maximum ratings, and electrical curves.
Where can I find the TS974IYD pinout?
The TS974IYD pinout should be taken from the pin-description and package-drawing sections of the STMicroelectronics TS97x family datasheet. The verified product listing confirms a 14-SOIC package with 14 pins, but it does not reproduce individual terminal names. Assign PCB tracks from the official pin table rather than inferring the four amplifier channels solely from the package outline.
Is TS974IYD suitable for audio preamplification?
The TS974IYD is suitable for audio preamplification because the STMicroelectronics TS97x family combines very low noise and low distortion characteristics with rail-to-rail output swing. Its 12 MHz gain-bandwidth product also provides useful bandwidth for many audio stages. The 1 µA quiescent current per channel also supports portable and battery-powered equipment, subject to output-swing and load checks.
Can TS974IYD operate from a 5 V supply?
Yes, the TS974IYD is identified for a nominal 5 V single supply and supports a stated single-supply range of 2.7 V to 10 V. According to the STMicroelectronics TS97x family documentation, operation can extend down to ±1.35 V in dual-supply arrangements. Confirm the signal levels, output load, input common-mode range, and bypass-capacitor arrangement for the actual circuit.
What can replace TS974IYD?
The closest identified same-family replacement is the STMicroelectronics TS974IDT, which retains the four-channel 14-SOIC format and the same nominal 12 MHz gain-bandwidth product. The ordering suffix indicates a different device grade, so the complete electrical, temperature, and qualification requirements must be checked before substitution. The available cross-reference results did not establish five pin-compatible alternatives.
Is TS974IYD the same as TS974IDT?
The TS974IYD and TS974IDT are closely related STMicroelectronics TS974 devices in the same 14-SOIC family, with four channels and a nominal 12 MHz gain-bandwidth product. They are not necessarily equivalent for every design because the ordering suffix can indicate a different grade or qualification class. Compare the manufacturer ordering table, temperature limits, and electrical characteristics before treating either part as a direct substitution.
When should I choose TS974IYD over TS974IDT?
Choose the TS974IYD when the design requires the specific ordering grade represented by TS974IYD, particularly when its temperature or qualification class has been established for the target application. Choose TS974IDT when its grade satisfies the product requirements and its documentation confirms compatible electrical limits. Both use the 14-SOIC format, so the deciding factors are specifications rather than a PCB footprint change.
Is TS974IYD suitable for portable sensor-conditioning circuits?
The TS974IYD is suitable for portable sensor conditioning because it combines a 2.7 V minimum single-supply operating point, rail-to-rail output swing, low 1 µA quiescent current per channel, and 200 nA input bias current. Its 60 dB common-mode rejection ratio can reduce the effect of common-mode interference, while 12 MHz bandwidth supports moderate-speed sensing signals. Sensor-specific headroom and noise requirements must still be checked.
What is the best Texas Instruments equivalent for TS974IYD?
No Texas Instruments equivalent can be confirmed as a drop-in replacement from the available cross-reference information. The identified TL974IPW comparison candidate uses a 14-pin small-outline package but does not establish the same physical footprint and exact pin compatibility required for a drop-in substitution. A footprint and pin-function comparison with the official TS974IYD package drawing is necessary before considering another manufacturer.
TS974IYD vs TS974IDT - which is better for a new design?
The TS974IYD is preferable when its exact ordering grade matches the required temperature range, qualification class, and purchasing configuration. TS974IDT is preferable when its manufacturer-defined grade meets the same requirements and offers a different supply configuration. Both use the 14-SOIC format and provide four channels with a nominal 12 MHz gain-bandwidth product, so the final decision should follow the complete ordering and electrical tables.
How much current can each TS974IYD channel output?
Each TS974IYD channel is listed with an output current capability of 100 mA. That rating should be checked against output swing, load type, supply voltage, and thermal conditions rather than treated as a constant-current source limit. The STMicroelectronics family documentation also identifies 1 µA quiescent current per channel and low-noise operation for portable equipment.
Where to buy TS974IYD online?
Use the Request a Quote form on this page to request current TS974IYD availability, order quantity, and lead time from XAIPART. The device is listed as a 14-SOIC, four-circuit, rail-to-rail operational amplifier by authorized distribution channels. Confirm the exact suffix and package before placing an order so the requested part is suitable for the target assembly.
What is the price and lead time for TS974IYD?
Current price and lead time should be requested through the Request a Quote form on this page because commercial terms can change with order quantity, packaging, and market conditions. The verified listings do not provide explicit quantity-break prices for the exact TS974IYD ordering code. Include your required quantity, target package, and production schedule when requesting the quotation.
Is TS974IYD in stock and what package does it use?
The TS974IYD is offered as a 14-SOIC device, and current availability should be confirmed through the Request a Quote form on this page. The part number identifies four rail-to-rail amplifier channels in the 14-SOIC configuration. Because the suffix also communicates ordering and delivery details, request the exact TS974IYD code rather than relying on a generic TS974 description.

Mühendislik referans verileri: TS974IYD — karşılaştırma, tasarım rehberi ve uyumluluk bilgileri.

Seçim Kılavuzu

Choose the TS974IYD when the system needs four general-purpose amplifiers operating from a 2.7 V to 10 V supply, particularly in portable audio, low-noise filtering, sensor conditioning, or compact measurement equipment. Its 12 MHz gain-bandwidth product, rail-to-rail output swing, 60 dB common-mode rejection ratio, and low 1 µA quiescent current per channel cover a broad range of low-voltage analog tasks. Choose TS974IDT when its exact ordering grade matches the required temperature, qualification, and sourcing conditions while retaining the same four-channel 14-SOIC architecture. A Texas Instruments alternative may be useful for broader sourcing, but the identified TL974IPW cannot be treated as a drop-in substitute without package and pin-level verification. Always compare the complete electrical table, input common-mode range, output-load behavior, and stability requirements rather than selecting solely from bandwidth or package name.

Alternatiflerle Karşılaştırma

Parametre Bu Ürün TS974IDT
Package 14-SOIC 14-SOIC
Brand STMicroelectronics STMicroelectronics
Number of Channels 4 circuits 4 circuits
Gain-Bandwidth Product 12 MHz 12 MHz
Output Swing Rail-to-rail Rail-to-rail

Ana Farklılayıcılar

  • Four matching amplifiers in one compact package (karşılaştırma:TS974IDT)
  • Low-power operation with useful signal bandwidth (karşılaştırma:TS974IDT)
  • Rail-to-rail output in a low-voltage quad-amplifier package (karşılaştırma:TS974IDT)

Tasarım Notları

Confirm that the circuit's supply remains within the 2.7 V to 10 V single-supply range or the ±1.35 V to ±5 V dual-supply range. Place the supply bypass capacitor close to the power pins and use the package-specific layout and capacitance guidance in the STMicroelectronics datasheet. Account for rail-to-rail output behavior and headroom rather than assuming the amplifier can swing exactly to either supply rail.

Keep each op-amp's feedback components and input traces compact to minimize parasitic capacitance and susceptibility to interference. The TS974IYD contains four amplifiers in one package, so provide adequate spacing between adjacent channels when low-noise or high-impedance work is involved. Route the ground return directly to the device and avoid sharing narrow paths with high-current switching or output-load returns.

Do not assume that rail-to-rail output swing guarantees rail-to-rail input operation. Check input common-mode limits, output swing under the intended load, closed-loop gain stability, capacitive-load tolerance, and the 100 mA per-channel output-current figure against the actual circuit. Also verify the exact ordering grade when using TS974IDT as a substitute because the suffix can denote different device requirements.

Uyumluluk Bilgisi

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Kadmiyumdan Arınmış
Unknown
Klorofillerden Arınmış
Unknown
Çatışma Minerali
Unknown

The available manufacturer-family information does not state the required compliance classifications. Use the current STMicroelectronics product documentation and declaration of compliance for production release.

Veri doğrulanma tarihi: 2026-11-10 — XAIPART bileşen mühendislik ekibi tarafından doğrulanmış ve derlenmiş veri

İlgili Aramalar

TS974IYD datasheet TS974IYD pinout TS974IYD datasheet pdf TS974IYD specifications TS974IYD equivalent TS974IYD replacement TS974IYD cross reference TS974IYD vs TS974IDT TS974IYD 14-SOIC footprint STMicroelectronics TS974IYD TS974IYD low noise op amp TS974IYD audio preamplifier TS974IYD price TS974IYD stock

İlgili Bileşenler ve Terimler

STMicroelectronics TS974IYD TS974IDT TS974 TL974IPW quad operational amplifier operational amplifier analog signal conditioner rail-to-rail output gain-bandwidth product common-mode rejection ratio input bias current quiescent current 14-SOIC SOIC package family surface mount SMD single-supply operation dual-supply operation audio preamplification sensor conditioning active filter battery-powered equipment low-noise amplification
Hızlı Teklif RFQ
Detayları tam doldurun — satış ekibimiz 24 saat içinde yanıt verecek
Parça Numarası Üretici Paket QTY Hedef Fiyat Genişletilmiş
✓
Teklif gönderildi!

24 saat içinde e-postanıza yanıt vereceğiz

1
RFQ Gönderildi
2
Teklif Alındı
3
Sipariş Yerleştirildi
4
Ödeme
5
Gönderildi
6
Teslim Edildi
RFQ Detaylarını Görüntüle