TS974IYD - 12MHz Quad Rail-to-Rail Op Amp | STMicroelectronics
料号: TS974IYD ✓ 量产中TS974IYD 概述
An operational amplifier is an analog signal-conditioning IC that compares an input voltage with a feedback-defined reference and amplifies the resulting error voltage. The TS974 belongs to the rail-to-rail operational amplifier hierarchy, where the output can approach the supply rails. This characteristic is useful when the available signal range is small, while its low-noise and low-distortion behavior make the TS97x family suitable for audio preamplification and portable instrumentation.
The TS974IYD combines four amplifiers in one 14-SOIC package. Each channel has a gain-bandwidth product of 12 MHz and supports up to 100 mA of output current. Its 60 dB common-mode rejection ratio improves immunity to common-mode voltage on the input pair, while the 200 nA input bias current and 1 µA quiescent current per channel suit low-power circuitry. These characteristics support portable and battery-powered equipment operating from low supply voltages.
The device supports both single- and dual-supply arrangements. In a single-supply system, the input and output signal range requires attention near the rails even though the output stage has rail-to-rail swing. In a dual-supply circuit, the stated operating range extends from ±1.35 V to ±5 V. Because the TS974 is intended for low-noise amplification, resistor selection, decoupling, grounding, and output-load compatibility remain central to achieving the intended signal quality.
Typical uses include portable audio preamplification, low-level sensor conditioning, battery-powered measurement equipment, active filters, and general-purpose analog signal processing. Four channels in one package also reduce board area when a system needs several similar gain stages. The package pin arrangement and electrical characteristics must be checked against the manufacturer datasheet before applying it to a new board or using it as a replacement.
For a new design, begin with the required signal bandwidth, output swing, supply voltage, and load current. Place the bypass capacitor near the power pins, keep feedback loops compact, and verify that input common-mode and output swing requirements remain valid at the chosen gain. For an existing PCB, confirm the 14-SOIC footprint, pin functions, and electrical limits before substituting another amplifier.
This page consolidates the available manufacturer-family information, distributor listing details, ordering guidance, and drop-in comparison considerations. It is designed to help engineers identify whether the TS974IYD fits a low-voltage, low-noise quad-op-amp design before moving to detailed circuit review and datasheet verification.
直接替换替代料: TS974IYD ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: TS974IYD (相同外形与封装尺寸) ——差异在于 Package.
TS974IYD 最大额定值与电气特性
| Number of Amplifier Channels | 4 circuits |
| Amplifier Type | General-purpose operational amplifier |
| Output Swing | Rail-to-rail |
| Gain-Bandwidth Product | 12 MHz |
| Output Current per Channel | 100 mA |
| Input Bias Current | 200 nA |
| Common-Mode Rejection Ratio | 60 dB |
| Quiescent Current per Channel | 1 µA |
| Single-Supply Voltage Range | 2.7 V to 10 V |
| Nominal Single-Supply Voltage | 5 V |
| Dual-Supply Voltage Range | ±1.35 V to ±5 V |
| 封装 | 14-SOIC, 3.90 mm body width |
| Total Pin Count | 14 pins |
TS974IYD 14-soic, 3.90 mm body width 引脚配置指南
TS974IYD(14-soic, 3.90 mm body width 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。
暂无详细引脚数据: TS974IYD.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TS974IYD 适用于 6 应用s: Portable Audio Preamplification, Battery-Powered Sensor Conditioning, Low-Noise Active Filters, Low-Voltage Signal Buffers, Battery-Supplied Measurement Equipment, General-Purpose Analog Signal Processing.
Portable Audio Preamplification
The TS974IYD is well suited to portable audio preamplification because the STMicroelectronics TS97x family combines very low noise, low distortion, and rail-to-rail output swing. Its 12 MHz gain-bandwidth product gives each channel ample bandwidth for common audio signal paths, while the 1 µA quiescent current per channel helps limit consumption in battery-operated equipment. Four amplifiers in one 14-SOIC package can implement successive gain stages, buffers, or active filtering without requiring four separate packages. Confirm the output swing into the intended load and ensure that the input signal remains inside the amplifier's common-mode range.
推荐
Battery-Powered Sensor Conditioning
The TS974IYD fits low-voltage sensor conditioning where low bias current and low standby consumption are important. Its 200 nA input bias current reduces loading on high-impedance sensors, while 1 µA quiescent current per channel supports battery life. The 60 dB common-mode rejection ratio helps reduce the effect of common-mode noise on differential measurements, and the 12 MHz bandwidth supports signals beyond static sensor outputs. Engineers should still verify input offset, noise density, common-mode limits, and the sensor's full-scale output against the complete STMicroelectronics electrical tables.
推荐
Low-Noise Active Filters
The TS974IYD can implement multiple active-filter stages because it provides four general-purpose amplifiers in a 14-SOIC package. Its 12 MHz gain-bandwidth product and rail-to-rail output capability are useful for low-frequency filters with signal levels that benefit from reduced clipping near the supply rails. Very low noise and low distortion make the device relevant to audio and precision signal-conditioning networks. Component tolerances, gain-bandwidth behavior, output loading, and stability at the selected closed-loop gain should be evaluated before production. The 100 mA per-channel output-current listing also requires a load check.
推荐
Low-Voltage Signal Buffers
The TS974IYD can provide voltage buffering when a sensor or divider produces a signal that must drive another circuit without additional loading. Rail-to-rail output swing increases usable signal range in compact 2.7 V to 10 V systems, and four channels allow several buffers to share one package. Low quiescent current of 1 µA per channel is valuable in portable equipment, while 12 MHz bandwidth supports responsive signal paths. Use unity-gain stability information, verify the capacitive-load limits, and keep feedback routing short so the buffer preserves signal integrity.
推荐
Battery-Supplied Measurement Equipment
The TS974IYD suits portable measurement equipment that needs several low-power analog channels. A single 14-SOIC package provides four amplifiers for transducer conditioning, gain adjustment, filtering, and output buffering. The low 1 µA quiescent current per channel helps conserve battery capacity, while operation from 2.7 V to 10 V supports cells, regulated rails, and dual-supply circuits down to ±1.35 V. The 60 dB common-mode rejection ratio is valuable when long sensor leads or switching converters introduce common-mode disturbance. Validate offset voltage, noise, input range, and calibration drift for the required measurement accuracy.
推荐
General-Purpose Analog Signal Processing
The TS974IYD is a practical quad-amplifier building block for general-purpose analog signal processing such as gain stages, comparators, integrators, and current-to-voltage converters. Its 12 MHz gain-bandwidth product supports a broad range of low-frequency and moderate-frequency tasks, while 200 nA input bias current reduces disturbance in high-impedance circuits. The 100 mA output current per channel provides headroom for conventional signal loads. Rail-to-rail output swing is advantageous in compact systems, but the designer must avoid relying on rail-to-rail input behavior unless it is explicitly confirmed in the complete electrical characteristics.
推荐
工程参考数据: TS974IYD ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TS974IDT |
|---|---|---|
| Package | 14-SOIC | 14-SOIC |
| Brand | STMicroelectronics | STMicroelectronics |
| Number of Channels | 4 circuits | 4 circuits |
| Gain-Bandwidth Product | 12 MHz | 12 MHz |
| Output Swing | Rail-to-rail | Rail-to-rail |
关键差异点
- Four matching amplifiers in one compact package (对比 TS974IDT)
- Low-power operation with useful signal bandwidth (对比 TS974IDT)
- Rail-to-rail output in a low-voltage quad-amplifier package (对比 TS974IDT)
设计说明
Confirm that the circuit's supply remains within the 2.7 V to 10 V single-supply range or the ±1.35 V to ±5 V dual-supply range. Place the supply bypass capacitor close to the power pins and use the package-specific layout and capacitance guidance in the STMicroelectronics datasheet. Account for rail-to-rail output behavior and headroom rather than assuming the amplifier can swing exactly to either supply rail.
Keep each op-amp's feedback components and input traces compact to minimize parasitic capacitance and susceptibility to interference. The TS974IYD contains four amplifiers in one package, so provide adequate spacing between adjacent channels when low-noise or high-impedance work is involved. Route the ground return directly to the device and avoid sharing narrow paths with high-current switching or output-load returns.
Do not assume that rail-to-rail output swing guarantees rail-to-rail input operation. Check input common-mode limits, output swing under the intended load, closed-loop gain stability, capacitive-load tolerance, and the 100 mA per-channel output-current figure against the actual circuit. Also verify the exact ordering grade when using TS974IDT as a substitute because the suffix can denote different device requirements.
合规信息
The available manufacturer-family information does not state the required compliance classifications. Use the current STMicroelectronics product documentation and declaration of compliance for production release.