Analog Devices

AD625ADZ - 25MHz Programmable Gain Amplifier | Analog Devices

MPN: AD625ADZ ✓ فعال
25 µV Vdss 16-CDIP, 0.300-inch (7.62 mm) width Package
MOQ: 1 |

AD625ADZ جائزہ

The Analog Devices AD625ADZ is a precision programmable-gain instrumentation amplifier with user-programmed gains up to 10,000, a 25 MHz gain-bandwidth product, 5 V/µs slew rate, and a 16-CDIP package. It supports low-noise differential measurement with 4 nV/√Hz input noise at 1 kHz, maximum gain error of 0.02%, and maximum low nonlinearity of 0.001%. The device is packaged in a 0.300-inch, 7.62 mm-wide 16-pin ceramic dual in-line package.

An instrumentation amplifier is a precision analog signal-conditioning amplifier optimized for measuring small differential signals superimposed on a large common-mode voltage. Its internal topology amplifies the difference between two inputs while rejecting common-mode noise. In the broader component hierarchy, the AD625 belongs to instrumentation amplifiers, a specialized class of amplifier ICs used in sensor measurement, data acquisition, medical instrumentation, and industrial control systems.

Programmable gain is the AD625ADZ's defining feature. The manufacturer identifies gains of 1 through 10,000 as user programmable, supporting both conventional resistor-selected gain and software-controlled measurement systems. A maximum gain error of 0.02% and gain temperature coefficient of 5 ppm/°C support repeatable scaling across changing temperatures. The specified 25 MHz gain-bandwidth product and 5 V/µs slew rate provide bandwidth for dynamically changing measurement signals rather than only static voltages.

The AD625's low-noise and precision characteristics make it suitable for demanding front ends. The published input-noise figure is 4 nV/√Hz at 1 kHz, while the listed low nonlinearity of 0.001% helps limit distortion when large differential signals are amplified. Its instrumentation-amplifier architecture supports bridge, current-loop, and other differential sensing arrangements where input bias current, offset, common-mode rejection, and gain accuracy can affect measurement quality.

Typical uses include weighing systems based on load cells, precision pressure and strain-gauge bridges, biomedical instrumentation, industrial process monitoring, and high-resolution data-acquisition channels. The ability to select a gain close to the full-scale differential input can improve use of the downstream converter's input range and reduce demands on its analog signal chain. Digital control of gain is also useful when measurements span several magnitudes.

A critical design consideration is gain implementation around the instrumentation amplifier. Follow the manufacturer's gain-setting table and observe the specified resistor values and tolerances because gain accuracy depends on both the amplifier and the external network. Provide adequate bypassing at the supply pins, maintain a common ground reference, and verify input and output voltage limits against the selected gain before connecting sensors or converters.

This product record combines the manufacturer's product information with pin-compatible family options and practical design guidance. It helps engineers distinguish the ceramic-DIP AD625ADZ from other AD625 package and temperature-grade variants while supporting component selection, schematic planning, and signal-chain design for precision measurement systems.

کے لیے ڈراپ اِن متبادل AD625ADZ — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں AD625ADZ (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Slew Rate, Number of Circuits, Amplifier Type, Input Bias Current.

Analog Devices
Package: 16-CDIP (0.300 inch, 7.62 mm)
Number of Circuits: 1 circuit
Amplifier Type: Instrumentation
موازنہ کریں AD625ADZ →
Analog Devices
Package: 16-CDIP, 0.300 inch pitch, 7.62 mm body
Slew Rate: 5 V/us
Number of Circuits: 1 circuit
موازنہ کریں AD625ADZ →
Analog Devices
Package: 16-pin PDIP
Input Bias Current: 30 nA
موازنہ کریں AD625ADZ →

AD625CDZ

✅ ڈراپ-اِن
Analog Devices
📦 16-CDIP (0.300-inch, 7.62 mm)
Instrumentation amplifier · 1 circuit · 25 MHz · 650 kHz · 5 V/us · 10 nA · +5 V · 16-CDIP, 0.300 inch pitch, 7.62 mm body

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

AD625BDZ

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
Analog Devices
📦 16-CDIP (0.300-inch, 7.62 mm)
Instrumentation · 1 circuit · Up to 10,000 · 0.02% · 5 ppm/°C · 0.001% · 25 MHz · 5 V/µs

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

AD625JNZ

✅ ڈراپ-اِن
Analog Devices
📦 16-CDIP (0.300-inch, 7.62 mm)
Single-channel precision instrumentation amplifier · 1 channel · ±18 V · -18 V to -6 V or +6 V to +18 V · Programmable with an external resistor · 0.02% · 650 kHz · 5 V/µs

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

AD625JN

✅ ڈراپ-اِن
Analog Devices
📦 16-pin DIP (0.300-inch, 7.62 mm)
Precision programmable-gain instrumentation amplifier · 1 channel · 1 to 10,000 · 0.02% maximum · 5 ppm/°C maximum · 0.001% maximum · 4 nV/√Hz at 1 kHz · 25 MHz

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

AD625JNZ

✅ ڈراپ-اِن
Analog Devices
📦 16-CDIP (0.300-inch, 7.62 mm)
Single-channel precision instrumentation amplifier · 1 channel · ±18 V · -18 V to -6 V or +6 V to +18 V · Programmable with an external resistor · 0.02% · 650 kHz · 5 V/µs

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

AD625ADZ زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

Amplifier Type Programmable-gain instrumentation amplifier
Number of Circuits 1
User-Programmed Gain Range 1 to 10,000
Gain-Bandwidth Product 25 MHz
Small-Signal Bandwidth 0.65 MHz
Slew Rate 5 V/µs
Maximum Low Gain Error 0.02%
Maximum Low Gain Temperature Coefficient 5 ppm/°C
Maximum Low Nonlinearity 0.001%
Input Noise Density 4 nV/√Hz at 1 kHz
Maximum Offset Voltage 25 µV
پیکیج 16-CDIP, 0.300-inch (7.62 mm) width
Packaging Tube
ماؤنٹنگ ٹائپ Through-hole

AD625ADZ 16-cdip, 0.300-inch (7.62 mm) width پن کنفیگریشن گائیڈ

AD625ADZ (16-cdip, 0.300-inch (7.62 mm) width پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔

AD625ADZ کے لیے 16-cdip, 0.300-inch (7.62 mm) width پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں AD625ADZ.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

AD625ADZ کے لیے موزوں ہے 6 ایپلیکیشنs: Load-Cell Weighing Systems, Strain-Gauge Pressure Measurement, Medical Patient Monitoring, Industrial Sensor Acquisition, Precision Data-Acquisition Systems, Current-Shunt Measurement.

⚡

Load-Cell Weighing Systems

The AD625ADZ fits precision load-cell front ends because its user-programmable gain of 1 to 10,000 can scale the small differential bridge output while its input noise is 4 nV/√Hz at 1 kHz. The instrumentation-amplifier arrangement rejects common-mode voltage present across the bridge, allowing the circuit to remain sensitive to the millivolt-level sensor signal. Place it at the bridge input and follow the manufacturer gain network to obtain predictable 0.02% maximum low gain error. This is particularly useful when multiple weight ranges require programmable scaling, although bridge excitation, common-mode range, and output swing must remain within the circuit limits.

🏭

Strain-Gauge Pressure Measurement

The AD625ADZ is suitable for strain-gauge pressure transducers that produce a small differential signal on a substantial common-mode voltage. Its programmable gain up to 10,000 provides the scaling required to use a larger portion of the downstream converter's input range, while 0.001% maximum low nonlinearity supports accurate measurement at relatively high gain. The 25 MHz gain-bandwidth product and 5 V/µs slew rate allow the front end to handle changing sensor conditions. Designers should verify the selected gain against output headroom and use the manufacturer's resistor values and common-mode limits to avoid saturation.

💊

Medical Patient Monitoring

The AD625ADZ can serve as the differential input stage in medical monitoring equipment where biopotential or sensor signals are much smaller than the surrounding common-mode voltage. Its 4 nV/√Hz input noise at 1 kHz and programmable gain up to 10,000 help preserve weak physiological information during amplification. The AD625 architecture is intended to provide gain accuracy and common-mode rejection for precision measurement rather than general-purpose signal conditioning. A medical design must additionally evaluate patient protection, isolation, applicable regulatory requirements, input protection, and the exact qualified supply and temperature conditions for the selected ordering option.

🏭

Industrial Sensor Acquisition

The AD625ADZ is appropriate for industrial sensor-acquisition channels that combine low-level differential outputs with substantial ground offsets or switching noise. Programmable gains from 1 to 10,000 let one analog front end cover multiple sensor ranges, and the 5 V/µs slew rate supports signals that change during the measurement cycle. Its 0.02% maximum low gain error and 5 ppm/°C gain temperature coefficient help maintain scaling across operating-temperature changes. Use appropriate input protection and shielding, verify the common-mode input range, and place bypass capacitors close to the supply pins to reduce susceptibility to industrial interference.

🖥️

Precision Data-Acquisition Systems

The AD625ADZ supports high-resolution data-acquisition systems that need selectable gain, low input noise, and accurate measurement scaling. A 25 MHz gain-bandwidth product provides more bandwidth than the listed 0.65 MHz small-signal bandwidth used for accurate signal measurement, while the 4 nV/√Hz noise specification supports high-resolution conversion. The device can be configured across gains from 1 to 10,000 as input amplitude changes. Use the appropriate external gain-setting components from the manufacturer reference circuit and verify settling behavior, converter input range, grounding, and common-mode limits for the selected sample rate.

⚡

Current-Shunt Measurement

The AD625ADZ can measure small voltage drops across low-value current shunts when the signal of interest is differential and common-mode voltage is present. Its programmable gain up to 10,000 increases sensitivity to the shunt voltage, while low input noise helps retain resolution at low current levels. The instrumentation amplifier configuration provides a practical way to reject system ground differences without relying on a general-purpose operational amplifier. The measurement remains dependent on shunt resistance, bandwidth, offset behavior, and error from the external gain network, so select the bandwidth and gain combination carefully and confirm that the shunt's common-mode voltage stays within the input limits.

تجویز کردہ پروڈکٹس کا خلاصہ

AD524 Digital potentiometer used to implement programmable gain control استعمال ہوتا ہے: Load-Cell Weighing Systems, Strain-Gauge Pressure Measurement, Medical Patient Monitoring, Industrial Sensor Acquisition, Precision Data-Acquisition Systems, Current-Shunt Measurement AD624 Precision instrumentation amplifier for fixed-gain bridge measurements استعمال ہوتا ہے: Load-Cell Weighing Systems, Strain-Gauge Pressure Measurement, Medical Patient Monitoring, Industrial Sensor Acquisition, Precision Data-Acquisition Systems, Current-Shunt Measurement
What are the key specifications of AD625ADZ that engineers should know?
The AD625ADZ is a precision instrumentation amplifier with user-programmed gain from 1 to 10,000, a 25 MHz gain-bandwidth product, a 0.65 MHz small-signal bandwidth, and a 5 V/µs slew rate. According to the Analog Devices datasheet, it also provides 4 nV/√Hz input noise at 1 kHz, maximum low gain error of 0.02%, maximum gain temperature coefficient of 5 ppm/°C, and maximum low nonlinearity of 0.001%. The device is offered in a 16-CDIP package and is intended for precision differential signal conditioning.
What is the operating voltage of AD625ADZ?
The AD625ADZ requires a dual supply in the range stated by the Analog Devices datasheet, but that numerical range is not reproduced in the product listing available for this page. Consult the electrical-characteristics table and supply-voltage-versus-output-voltage plots before finalizing the power rails. Because this is an instrumentation amplifier, the selected supply must also support the required input and output swing at every programmed gain.
What is the gain range of the AD625ADZ?
The AD625ADZ supports user-programmed gains from 1 to 10,000. According to the Analog Devices product page, this wide range enables one device to serve both conventional resistor-programmed circuits and precision software-programmable gain systems. When using an external gain network, follow the manufacturer's gain-setting table because the specified maximum low gain error of 0.02% applies only when the required resistor network and operating conditions are met.
Where can I download the AD625ADZ datasheet PDF?
The official AD625ADZ datasheet and supporting product information are available through the Analog Devices product page at https://www.analog.com/en/products/ad625.html. Use the manufacturer's Data Sheet, Rev. D as the authoritative reference for the pin description, recommended gain-setting resistors, supply requirements, input and output limits, and performance curves. The AD625ADZ is the 16-CDIP ordering variant, so verify the package code before applying the document to a schematic or PCB footprint.
Where can I find the AD625ADZ pinout?
The AD625ADZ pin assignment is defined in the pin-description table of the Analog Devices AD625 data sheet, Rev. D. It uses a 16-CDIP package with 0.300-inch pin spacing, and the pin functions include the differential signal inputs, gain-setting connections, supply rails, reference input, and output stages described for the AD625 family. Use that table for the exact numbered pin assignment and do not substitute a generic DIP drawing.
How noisy is the AD625ADZ?
The AD625ADZ has an input noise density of 4 nV/√Hz at 1 kHz. According to the Analog Devices data sheet, this low-noise performance is intended for precision differential measurements in which the input signal may be comparable to the amplifier's own noise. In practice, the total system noise also depends on source impedance, gain bandwidth, the external gain-setting network, and the bandwidth of the following converter.
Is AD625ADZ suitable for load-cell and strain-gauge measurement?
Yes, the AD625ADZ is well suited to low-level bridge measurements because it combines programmable gain up to 10,000 with low input noise and precise gain characteristics. It can amplify the small differential voltage generated by a load cell or strain-gauge bridge while rejecting the larger common-mode bridge voltage. The final design must still verify the common-mode range, output swing, gain resistor network, and bridge excitation requirements for the selected sensor.
When should I choose AD625ADZ over an AD624?
Choose the AD625ADZ when the design needs programmable or nonstandard gains beyond the gain options naturally supported by the AD624. The AD625 supports user-programmed gains from 1 to 10,000 and is specifically positioned for precision software-programmable measurement systems and circuits requiring flexible gain selection. The AD624 remains appropriate when its fixed or externally determined gain set already covers the application and the AD625's additional flexibility is unnecessary.
What is the difference between AD625ADZ and AD625CDZ?
Both AD625ADZ and AD625CDZ are AD625-family instrumentation amplifiers associated with the 16-CDIP package, and they use the same basic amplifier architecture and programmable-gain approach. Their ordering distinctions identify different manufacturer grades or variants, so the device temperature range and exact ordering information should be confirmed in the Analog Devices data sheet. For a direct substitution, verify those grade-specific requirements in addition to matching the pinout.
What can replace AD625ADZ?
The closest documented drop-in options are same-package AD625 family variants such as AD625CDZ, AD625BDZ, AD625JNZ, AD625JN, and AD625JNZ, subject to confirmation of the exact grade and temperature range. These options preserve the 16-DIP footprint and AD625 gain architecture, but a valid replacement must also satisfy the original circuit's supply, temperature, gain-setting, and qualification requirements. Review the Analog Devices ordering information before approving a substitution.
Is AD625ADZ the same as AD625JNZ?
No, AD625ADZ and AD625JNZ are not identical ordering codes even though both belong to the AD625 precision instrumentation-amplifier family. AD625ADZ is identified as a 16-CDIP device, while AD625JNZ represents another AD625 ordering configuration whose exact package and grade must be checked. They may be electrically similar, but a replacement requires verification of pin assignment, package geometry, temperature range, and electrical limits rather than reliance on the base device name.
Where can I buy AD625ADZ and how do I request a quote?
Use the Request a Quote form on this page to request AD625ADZ pricing, availability, and lead time. The manufacturer's product page identifies AD625 as not recommended for new designs, so lifecycle planning is important for systems still using the family. The exact AD625ADZ order code, tube packaging requirement, and any date-code or traceability constraints should be stated in the quote request.
What is the price of AD625ADZ?
Current AD625ADZ pricing is obtained through the Request a Quote form on this page rather than a static price in this description. The component is supplied in a tube and is associated with the 16-CDIP package, so confirm the complete ordering code before requesting a quotation. Because Analog Devices identifies AD625 as not recommended for new designs, buyers should also discuss lifecycle support and planned production volumes with the supplier.
Is AD625ADZ in stock and what is its lead time?
Current AD625ADZ stock and lead time should be confirmed through the Request a Quote form on this page. The 16-CDIP package is supplied in a tube, and the manufacturer identifies the AD625 family as not recommended for new designs. For an ongoing production program, include forecast quantities, required delivery dates, and any traceability needs in the request so the supplier can confirm allocation and schedule.
What is the lifecycle status of AD625ADZ?
Analog Devices lists AD625 as not recommended for new designs, so new production programs should confirm lifecycle support before committing to the family. The AD625ADZ remains a legacy-orderable option where an existing design requires the exact 16-CDIP instrumentation amplifier. For long-lived or safety-relevant equipment, request written supply, quality, and lifecycle information through the Request a Quote form on this page.
How should a software-programmable gain circuit use the AD625ADZ?
The AD625ADZ can implement a software-programmable gain stage by selecting an appropriate gain configuration for each measurement range, allowing the instrument to accommodate widely varying signal amplitudes. Its programmable gain from 1 to 10,000 and 25 MHz gain-bandwidth product are useful for such systems, while the 0.02% maximum low gain error supports controlled scaling. Follow the manufacturer's gain-setting network and switching guidance, and account for relay or switch resistance, noise, and settling time in the final signal chain.

کے لیے انجینئرنگ ریفرنس ڈیٹا AD625ADZ — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the AD625ADZ for legacy or maintenance designs that require the exact 16-CDIP AD625 ordering code, user-programmable gain from 1 to 10,000, low input noise, and precise differential signal conditioning. Select AD625CDZ or AD625JNZ when their confirmed grade and temperature range meet the application and the ceramic-DIP footprint is compatible. Consider AD625JN for a pin-compatible 16-DIP configuration when its package grade is acceptable. Use AD625BDZ only after checking the manufacturer's ordering table for temperature-range and qualification differences. For designs without a legacy footprint constraint, compare the AD625 against the AD624: the AD624 may simplify a fixed-gain bridge circuit, while the AD625 provides substantially more gain-selection flexibility. Because Analog Devices identifies AD625 as not recommended for new designs, confirm lifecycle support before starting a new production program.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ AD625CDZ AD625BDZ AD625JNZ AD625JN AD625JNZ
Package 16-CDIP (0.300-inch, 7.62 mm) 16-CDIP (0.300-inch, 7.62 mm) 16-CDIP (0.300-inch, 7.62 mm) 16-CDIP (0.300-inch, 7.62 mm) 16-pin DIP (0.300-inch, 7.62 mm) 16-CDIP (0.300-inch, 7.62 mm)
Brand Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices Analog Devices
Amplifier Type Programmable-gain instrumentation amplifier Programmable-gain instrumentation amplifier Programmable-gain instrumentation amplifier Programmable-gain instrumentation amplifier Programmable-gain instrumentation amplifier Programmable-gain instrumentation amplifier
Number of Circuits 1 1 1 1 1 1
User-Programmed Gain Range 1 to 10,000 1 to 10,000 1 to 10,000 1 to 10,000 1 to 10,000 1 to 10,000
Gain-Bandwidth Product 25 MHz 25 MHz 25 MHz 25 MHz 25 MHz 25 MHz
Small-Signal Bandwidth 0.65 MHz 0.65 MHz 0.65 MHz 0.65 MHz 0.65 MHz 0.65 MHz
Slew Rate 5 V/µs 5 V/µs 5 V/µs 5 V/µs 5 V/µs 5 V/µs
Maximum Low Gain Error 0.02% 0.02% 0.02% 0.02% 0.02% 0.02%
Maximum Low Gain Temperature Coefficient 5 ppm/°C 5 ppm/°C 5 ppm/°C 5 ppm/°C 5 ppm/°C 5 ppm/°C
Maximum Low Nonlinearity 0.001% 0.001% 0.001% 0.001% 0.001% 0.001%
Input Noise Density 4 nV/√Hz at 1 kHz 4 nV/√Hz at 1 kHz 4 nV/√Hz at 1 kHz 4 nV/√Hz at 1 kHz 4 nV/√Hz at 1 kHz 4 nV/√Hz at 1 kHz

اہم امتیازی خصوصیات

  • Broad programmable gain range for precision measurement (بمقابلہAD624)
  • Low-noise input suitable for weak differential signals (بمقابلہAD625CDZ)
  • High available gain-bandwidth for changing measurement conditions (بمقابلہAD625JN)
  • Flexible gain supports multi-range acquisition systems (بمقابلہAD625JNZ)

ڈیزائن نوٹس

Implement the AD625 gain network with the resistor values specified in the manufacturer gain-setting tables, and connect the gain-setting pins with short, low-loop-area traces. At high gain, resistor tolerance and thermal gradients can materially affect scale accuracy, so use the specified resistor technology and avoid routing sensitive gain nodes beside high-current or switching nodes. Keep the input pair physically close and provide a quiet ground reference to minimize noise pickup and common-mode conversion.

Decouple each supply rail directly at the AD625ADZ with the capacitance and ESR requirements shown in the manufacturer's application guidance. Check supply headroom against the selected gain because a large gain can move the internal operating point close to an input or output limit. Place bypass components near the device pins and keep their ground returns short. Also account for supply ripple and the amplifier's power-supply rejection when the source signal is small.

Verify common-mode input range, output swing, and gain at the worst-case sensor or source condition before finalizing the schematic. The 0.65 MHz small-signal bandwidth and 25 MHz gain-bandwidth product do not remove the need for an input filter appropriate to the source. For bridge sensors, include input-overvoltage protection that does not introduce excessive leakage, and use shielded or guarded routing where EMI could be rectified by the high-impedance input nodes.

Do not select the AD625 solely by its maximum gain of 10,000. Gain error, offset, noise, bandwidth, output swing, and common-mode limits vary across the gain range, and a high gain can reduce usable input headroom. Validate the complete signal chain with the actual gain-setting network and source impedance. Also confirm that the selected ordering variant satisfies the required temperature grade before treating a family member as a drop-in replacement.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The AD625 is an instrumentation amplifier rather than an automotive-qualified device. No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for this exact ordering code in the available product information.

متعلقہ تلاشیں

AD625ADZ datasheet AD625ADZ pinout AD625ADZ datasheet pdf AD625ADZ equivalent AD625ADZ replacement AD625ADZ drop-in replacement AD625ADZ vs AD624 AD625ADZ application circuit AD625ADZ 16-CDIP footprint AD625ADZ programmable gain 10000 AD625ADZ 25MHz gain bandwidth AD625ADZ price AD625ADZ stock Analog Devices AD625ADZ

متعلقہ اجزاء اور اصطلاحات

Analog Devices AD625ADZ AD625 AD624 AD524 AD625CDZ AD625BDZ AD625JNZ AD625JN AD625JNZ programmable-gain instrumentation amplifier instrumentation amplifier precision analog amplifier amplifier IC semiconductor differential signal conditioning common-mode rejection gain-bandwidth product slew rate input noise density gain error nonlinearity 16-CDIP DIP package through-hole package load-cell measurement strain-gauge bridge industrial sensor acquisition medical monitoring
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں