Analog Devices

AD626ANZ - Low-Cost Single-Supply Differential Amp | Analog Devices

MPN: AD626ANZ ✓ فعال
2.4 V to 10 V Vdss 8-pin PDIP Package
MOQ: 1 |

AD626ANZ جائزہ

The Analog Devices AD626ANZ is a low-cost, true single-supply differential amplifier designed for amplifying and low-pass filtering small differential signals that carry a large common-mode voltage. It operates from a single supply of 2.4 V to 10 V or from dual supplies of ±1.2 V to ±6 V and is packaged in an 8-pin PDIP. The device provides one amplifier circuit with a differential input stage suitable for precision signal-conditioning and measurement systems.

A differential amplifier measures the voltage difference between two input nodes while rejecting voltage common to both inputs. Within the broader semiconductor hierarchy, the AD626 is an operational-amplifier-based signal-conditioning IC, then an amplifier, then an analog integrated circuit used within data-acquisition and instrumentation systems. This category is especially useful when a sensor output is much smaller than the voltage shared by both sensor terminals.

The AD626ANZ supports a broad 2.4 V to 10 V single-supply operating range, allowing operation from low-voltage systems as well as conventional industrial rails. Its stated input offset voltage is 2.5 mV, its common-mode rejection is 100 dB, and its gain bandwidth product is 100 kHz. These characteristics make it suitable for current-loop measurements, bridge-amplifier interfaces, sensor conditioning, and low-frequency filtering.

The input common-mode range extends to approximately 6 times the positive supply minus 1 V, as stated by the manufacturer, allowing the amplifier to process signals above its supply voltage when the circuit polarity and operating conditions permit. This characteristic helps designers handle high-side sensing and current-shunt measurements without first reducing the common-mode voltage through additional active circuitry.

Typical applications include precision current measurement, industrial sensor interfaces, low-pass differential filters, medical instrumentation, and data-acquisition front ends. The 8-pin PDIP package is also suitable for through-hole prototyping and designs where a leaded package simplifies inspection and rework.

The principal design constraint is signal bandwidth: with a 100 kHz gain bandwidth product, the usable closed-loop bandwidth depends on the configured gain. Higher closed-loop gain reduces bandwidth and should be checked against the required filter response and settling behavior. Input and feedback resistors also determine practical accuracy and noise performance.

This page combines manufacturer operating limits, a package-specific drop-in assessment, and practical replacement guidance. It helps engineers distinguish a true pin-compatible replacement from merely similar instrumentation amplifiers that use different packages or gain architectures.

کے لیے ڈراپ اِن متبادل AD626ANZ — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

AD626AN

✅ ڈراپ-اِن
📦 8-pin PDIP
No identified functional difference; the comparison reports consistent performance, terminals, and package, giving 100% parameter proximity

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

AD626BNZ

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
📦 8-pin PDIP
Same AD626 family and PDIP package; available comparison does not quantify the B-versus-A temperature-grade difference

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

AD626ANZ زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

Product Type Single-supply differential amplifier
Number of Amplifier Circuits 1 circuit
Single-Supply Operating Voltage 2.4 V to 10 V
Dual-Supply Operating Voltage ±1.2 V to ±6 V
Input Offset Voltage 2.5 mV
Common-Mode Rejection 100 dB
Gain Bandwidth Product 100 kHz
Input Common-Mode Range Approximately 6 × (+VS − 1 V)
آپریٹنگ درجہ حرارت رینج -40 °C to 85 °C
پیکیج 8-pin PDIP
ماؤنٹنگ ٹائپ Through-hole
Single-Supply Compatibility True single-supply operation
Differential Signal Capability Amplification and low-pass filtering of small differential voltages
Common-Mode Rejection Function Rejection of voltage common to both inputs
RoHS اسٹیٹس unknown
REACH Status unknown
AEC-Q100 Qualification not_applicable
Lead-Free Status unknown
Halogen-Free Status unknown

AD626ANZ 8-pin pdip پن کنفیگریشن گائیڈ

AD626ANZ (8-pin pdip پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔

AD626ANZ کے لیے 8-pin pdip پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں AD626ANZ.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

AD626ANZ کے لیے موزوں ہے 6 ایپلیکیشنs: Current-Shunt Measurement, Bridge-Sensor Signal Conditioning, Medical Instrumentation Front End, Low-Pass Differential Filter, Battery-Powered Data Acquisition, High-Common-Mode Sensor Interface.

⚡

Current-Shunt Measurement

The AD626ANZ fits current-shunt front ends where a small differential voltage appears across a resistor while both input nodes carry a much larger common-mode voltage. Its 100 dB common-mode rejection helps prevent the common-mode component from dominating the measured result, and the 2.5 mV input offset specification is important when shunt drops are small. The single-supply range of 2.4 V to 10 V supports compact industrial systems. Configure the amplifier for the required differential gain while checking that the shunt common-mode voltage remains inside the specified input range and that the output does not approach either supply rail.

🏭

Bridge-Sensor Signal Conditioning

A strain-gauge or resistive bridge produces a small differential output around a substantial bridge excitation common-mode voltage, making the AD626ANZ appropriate for extracting and filtering the bridge signal. The 100 dB common-mode rejection reduces sensitivity to common supply and excitation variations, while the 100 kHz gain bandwidth product is suitable for low-frequency force, pressure, and displacement measurements. Use the manufacturer's recommended resistor network and verify that the excitation-derived common-mode voltage does not exceed the amplifier's input range. The 8-pin PDIP format is particularly convenient for instrumentation prototypes requiring straightforward through-hole assembly.

💊

Medical Instrumentation Front End

The AD626ANZ can condition small differential signals from biomedical electrodes and isolated sensor interfaces where common-mode pickup may exceed the wanted signal. Its 2.5 mV input offset and 100 dB common-mode rejection support low-level differential measurements, and operation from 2.4 V to 10 V can simplify portable equipment power architecture. The amplifier should be surrounded by suitable input protection because medical sensor inputs may require isolation and leakage considerations beyond the amplifier's basic signal specification. Confirm noise, accuracy, patient-safety requirements, and applicable regulatory approvals at the complete-system level.

🔧

Low-Pass Differential Filter

The AD626ANZ supports amplification and low-pass filtering of small differential voltages, matching noisy sensor channels that require both common-mode rejection and bandwidth limiting. Its 100 kHz gain bandwidth product leaves headroom for an external feedback network that shapes the final filter response, but the usable bandwidth decreases as closed-loop gain rises. Select feedback resistors and capacitors using the manufacturer's application guidance, and place the network close to the relevant pins to reduce unwanted coupling. Verify settling behavior and filter attenuation at the highest signal frequency expected in the measurement channel.

📱

Battery-Powered Data Acquisition

The AD626ANZ is suitable for compact, battery-powered data-acquisition modules because it supports a 2.4 V minimum single supply and rejects common-mode noise without requiring dual rails. The low-cost differential architecture is useful when sampling sensors, resistive dividers, or remote measurement lines where unequal ground potentials would impair a single-ended amplifier. At low supply voltages, carefully verify input common-mode range, output swing, and the offset contribution of the selected gain network. The 8-pin PDIP package is also useful during prototype development, although a surface-mount variant would generally be preferred for a high-volume compact assembly.

🧩

High-Common-Mode Sensor Interface

The AD626ANZ is appropriate when a sensor produces a small differential voltage on top of a large common-mode potential, particularly in industrial current and voltage monitoring. Its stated input common-mode range of approximately 6 times positive supply minus 1 V provides design margin above ordinary signal levels, while the 100 dB common-mode rejection suppresses shared interference. This capability can reduce the need for a separate common-mode attenuation stage. The complete design must still verify that the calculated common-mode and differential signals stay within the data-sheet limits across supply tolerance, temperature range, and component variation.

تجویز کردہ پروڈکٹس کا خلاصہ

AD626ANZ Analog Devices استعمال ہوتا ہے: Current-Shunt Measurement, Bridge-Sensor Signal Conditioning, Medical Instrumentation Front End, Low-Pass Differential Filter, Battery-Powered Data Acquisition, High-Common-Mode Sensor Interface AD626AN Pin-compatible shunt amplifier option استعمال ہوتا ہے: Current-Shunt Measurement, Medical Instrumentation Front End, Battery-Powered Data Acquisition, High-Common-Mode Sensor Interface AD626BNZ AD626 family bridge-interface option استعمال ہوتا ہے: Bridge-Sensor Signal Conditioning, Low-Pass Differential Filter
What is the operating voltage of AD626ANZ?
The AD626ANZ operates from 2.4 V to 10 V with a single supply or from ±1.2 V to ±6 V with dual supplies. According to the Analog Devices AD626 product page, the device is a true single-supply differential amplifier, so a single positive rail is sufficient when the signal and output ranges remain compatible with that rail.
What type of amplifier is AD626ANZ?
The AD626ANZ is a one-circuit, true single-supply differential amplifier in an 8-pin PDIP package. Analog Devices describes it as a low-cost amplifier for processing small differential voltages in the presence of a large common-mode voltage. It can amplify and low-pass filter signals from bridge, shunt, and other sensor interfaces.
What are the key specifications of AD626ANZ that engineers should know?
The principal AD626ANZ specifications are a 2.4 V to 10 V single-supply range, a 2.5 mV input offset voltage, 100 dB common-mode rejection, and a 100 kHz gain bandwidth product. The manufacturer also specifies an input common-mode range of approximately 6 times positive supply minus 1 V. These limits define its suitability for low-frequency precision signal conditioning.
Where can I download the AD626ANZ datasheet PDF?
The official AD626ANZ documentation is available from the Analog Devices product page at https://www.analog.com/en/products/ad626.html, which links to manufacturer data and supporting material. Use the manufacturer's pin configuration and electrical-characteristics tables when assigning PCB connections, selecting resistors, and confirming the 8-pin PDIP pinout.
Where can I find the AD626ANZ pinout?
The AD626ANZ uses an 8-pin PDIP package, and its connection information should be taken from the pin-configuration table in the Analog Devices AD626 datasheet. The product page is the appropriate starting point. Confirm the amplifier inputs, output, supply pins, and any reference or feedback connections directly against the manufacturer drawing before PCB release.
What can replace the AD626ANZ?
The closest identified drop-in replacement is AD626AN because a product comparison reports consistent performance, terminals, and package, indicating that it can replace AD626ANZ without circuit modification. Instrumentation amplifiers such as INA114, INA121, INA128, and LTC6090 offer related functionality but are not established as pin-compatible replacements for the 8-pin AD626ANZ.
Is AD626AN the same as AD626ANZ?
AD626AN and AD626ANZ are reported to have consistent main performance characteristics, terminals, and package, so AD626AN can serve as a drop-in replacement for AD626ANZ. The exact ordering-code and environmental qualifications should nevertheless be checked against the current Analog Devices ordering guide before using the interchange in a qualified or regulated production design.
What is the best Texas Instruments equivalent for AD626ANZ?
The Texas Instruments INA114, INA121, and INA128 are functional alternatives for instrumentation-amplifier applications, but they are not verified pin-to-pin replacements for the 8-pin AD626ANZ. The AD626 uses a differential-amplifier configuration, whereas these INA devices generally use an instrumentation-amplifier architecture and have different packages, gain-setting methods, and supply requirements.
When should I choose AD626ANZ over a general-purpose operational amplifier?
Choose AD626ANZ when the signal of interest is the difference between two inputs and the surrounding common-mode voltage is substantially larger than that difference. Its differential architecture, 100 dB common-mode rejection, and specified common-mode range are more directly aligned with shunt, bridge, and sensor measurements than a single-ended amplifier configured by external subtraction.
Is AD626ANZ suitable for current-shunt measurement?
The AD626ANZ is suitable for low-frequency current-shunt measurement when the shunt common-mode voltage remains within the device's input range. Its 100 dB common-mode rejection helps suppress errors from the larger common-mode voltage, while the 100 kHz gain bandwidth product supports modest signal bandwidth. Check the common-mode range and amplifier output swing against the actual shunt circuit.
AD626ANZ vs AD626BNZ: which one should be selected?
AD626ANZ and AD626BNZ are related Analog Devices variants, but the available comparison identifies them as separate ordering options rather than guaranteeing identical electrical ratings. Select AD626ANZ when its documented supply range, temperature range, and other ordering specifications satisfy the design. Compare both manufacturer ordering tables before selecting AD626BNZ as a substitute.
Where to buy AD626ANZ online?
Use the Request a Quote form on this page to request AD626ANZ pricing, stock confirmation, and lead time for the exact 8-pin PDIP ordering code. The form is the appropriate channel for current commercial availability because catalog pricing and inventory can change independently of the product's technical specification.
What is the lead time for AD626ANZ?
Current lead time for AD626ANZ should be requested through the Request a Quote form on this page. Lead time depends on factory availability, packaging, order quantity, and current component allocation, so it should not be inferred from general catalog listings. Specify the required quantity and whether reels, cut tape, or other permitted delivery configurations are needed.
Is AD626ANZ in stock?
Current AD626ANZ inventory should be confirmed with the Request a Quote form on this page. Some catalog pages indicate availability, but stock levels can change rapidly and may differ by package and shipment location. Submit the exact MPN, quantity, and target delivery region to obtain a current availability response.
What is the price of AD626ANZ?
Current pricing for AD626ANZ is available through the Request a Quote form on this page. The form accepts the required quantity and lets purchasing confirm the applicable unit and volume tiers. Pricing is not embedded in this FAQ because commercial conditions and component availability can change independently of the amplifier's technical characteristics.
Does AD626ANZ comply with RoHS and REACH?
The RoHS and REACH status of AD626ANZ should be confirmed from the current Analog Devices product documentation or declaration of conformity. The available product material does not establish those declarations directly, so the responsible compliance classification remains unknown. Do not infer lead-free or halogen-free status solely from the ANZ ordering code.

کے لیے انجینئرنگ ریفرنس ڈیٹا AD626ANZ — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose AD626ANZ when the design needs a low-cost, true single-supply differential amplifier in an 8-pin PDIP package and can operate within the 2.4 V to 10 V supply range. Its 2.5 mV offset, 100 dB common-mode rejection, and 100 kHz gain bandwidth product make it appropriate for low-frequency shunt, bridge, and sensor measurements. Select AD626AN when its ordering code is preferable and the reported consistent terminals and package satisfy your interchange requirements. Consider AD626BNZ only after comparing the exact A-versus-B temperature-grade ratings in the current ordering guide. INA114, INA121, INA128, and LTC6090 can solve related instrumentation-amplifier problems, but they should not be treated as drop-in replacements without a separate pinout and parametric review because their gain-setting methods, packages, and electrical characteristics differ.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ AD626AN AD626BNZ
Package 8-pin PDIP 8-pin PDIP - same package 8-pin PDIP - same package
Brand Analog Devices Analog Devices Analog Devices
Product Type True single-supply differential amplifier Differential amplifier Differential amplifier
Number of Amplifier Circuits 1 circuit 1 circuit 1 circuit

اہم امتیازی خصوصیات

  • Verified same-package replacement path (بمقابلہAD626AN)
  • True single-supply operation from 2.4 V (بمقابلہAD626AN)
  • Strong common-mode rejection for differential sensing (بمقابلہAD626BNZ)

ڈیزائن نوٹس

Do not treat a high common-mode input voltage as permission to exceed the absolute maximum ratings. The manufacturer describes an input common-mode range of approximately 6 times positive supply minus 1 V, but supply tolerances, transient overshoot, and input protection currents must also be included in the design. Check the absolute-maximum table and use appropriate series resistance or clamping when the source can exceed the operating limits.

Confirm the output swing at the selected supply voltage before choosing a high closed-loop gain. A 2.4 V to 10 V single supply allows flexible rail selection, but the useful output range still depends on load current and the amplifier's output-capacitance stability requirements. Analyze the signal chain at both supply extremes and avoid operating the output close to either rail unless the manufacturer explicitly permits it.

Keep the differential input traces short, symmetrical, and away from switching nodes and high-current paths. Place the feedback network and any filtering components close to the amplifier pins to minimize parasitic capacitance and pickup. Because the AD626 is intended to reject common-mode voltage, unequal input routing or ground currents can reintroduce differential error; use a compact, symmetric layout and a quiet return path.

The 100 kHz gain bandwidth product imposes a gain-dependent bandwidth limit. For example, higher closed-loop gain reduces the frequency range over which the amplifier can respond accurately, so a shunt or bridge measurement requiring wide bandwidth should use a lower gain or a faster amplifier. Evaluate the complete transfer function, including the external filter network, rather than relying only on the nominal gain bandwidth product.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The available manufacturer product information does not directly state the requested environmental declarations. Automotive qualification is treated as not applicable because this is an industrial-style Analog Devices differential amplifier rather than an identified automotive-qualified variant.

متعلقہ تلاشیں

AD626ANZ datasheet AD626ANZ pinout AD626ANZ datasheet pdf AD626ANZ equivalent AD626ANZ replacement AD626ANZ vs AD626AN AD626ANZ price AD626ANZ stock Analog Devices AD626ANZ AD626ANZ single supply differential amplifier AD626ANZ common mode rejection AD626ANZ application circuit

متعلقہ اجزاء اور اصطلاحات

Analog Devices AD626ANZ AD626AN AD626BNZ INA114 INA121 INA128 LTC6090 differential amplifier operational amplifier amplifier IC analog integrated circuit signal conditioning common-mode voltage common-mode rejection input offset voltage gain bandwidth product true single-supply operation 8-pin PDIP PDIP package through-hole mounting current-shunt measurement bridge sensor low-pass filter data acquisition
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں