AD626ANZ - Low-Cost Single-Supply Differential Amp | Analog Devices
部品番号: AD626ANZ ✓ 生産中AD626ANZ 概要
A differential amplifier measures the voltage difference between two input nodes while rejecting voltage common to both inputs. Within the broader semiconductor hierarchy, the AD626 is an operational-amplifier-based signal-conditioning IC, then an amplifier, then an analog integrated circuit used within data-acquisition and instrumentation systems. This category is especially useful when a sensor output is much smaller than the voltage shared by both sensor terminals.
The AD626ANZ supports a broad 2.4 V to 10 V single-supply operating range, allowing operation from low-voltage systems as well as conventional industrial rails. Its stated input offset voltage is 2.5 mV, its common-mode rejection is 100 dB, and its gain bandwidth product is 100 kHz. These characteristics make it suitable for current-loop measurements, bridge-amplifier interfaces, sensor conditioning, and low-frequency filtering.
The input common-mode range extends to approximately 6 times the positive supply minus 1 V, as stated by the manufacturer, allowing the amplifier to process signals above its supply voltage when the circuit polarity and operating conditions permit. This characteristic helps designers handle high-side sensing and current-shunt measurements without first reducing the common-mode voltage through additional active circuitry.
Typical applications include precision current measurement, industrial sensor interfaces, low-pass differential filters, medical instrumentation, and data-acquisition front ends. The 8-pin PDIP package is also suitable for through-hole prototyping and designs where a leaded package simplifies inspection and rework.
The principal design constraint is signal bandwidth: with a 100 kHz gain bandwidth product, the usable closed-loop bandwidth depends on the configured gain. Higher closed-loop gain reduces bandwidth and should be checked against the required filter response and settling behavior. Input and feedback resistors also determine practical accuracy and noise performance.
This page combines manufacturer operating limits, a package-specific drop-in assessment, and practical replacement guidance. It helps engineers distinguish a true pin-compatible replacement from merely similar instrumentation amplifiers that use different packages or gain architectures.
ドロップイン代替品: AD626ANZ — 同一パッケージでピン互換。PCBの作り直しが必要な異なるパッケージの部品は除外されています。
AD626AN
✅ ドロップイン📋 参考代替品(カタログ未掲載)
AD626BNZ
✅ ドロップイン ⚠️ 仕様未検証📋 参考代替品(カタログ未掲載)
AD626ANZ 最大定格&電気的特性
| Product Type | Single-supply differential amplifier |
| Number of Amplifier Circuits | 1 circuit |
| Single-Supply Operating Voltage | 2.4 V to 10 V |
| Dual-Supply Operating Voltage | ±1.2 V to ±6 V |
| Input Offset Voltage | 2.5 mV |
| Common-Mode Rejection | 100 dB |
| Gain Bandwidth Product | 100 kHz |
| Input Common-Mode Range | Approximately 6 × (+VS − 1 V) |
| 動作温度範囲 | -40 °C to 85 °C |
| パッケージ | 8-pin PDIP |
| 実装タイプ | Through-hole |
| Single-Supply Compatibility | True single-supply operation |
| Differential Signal Capability | Amplification and low-pass filtering of small differential voltages |
| Common-Mode Rejection Function | Rejection of voltage common to both inputs |
| RoHS ステータス | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
| Lead-Free Status | unknown |
| Halogen-Free Status | unknown |
AD626ANZ 8-pin pdip ピン配置ガイド
AD626ANZ (8-pin pdip パッケージ) のピン配置。 このアナログコンポーネントは、入力、出力、および電源ピンを備えています。オフセットナル、補償、イネーブルピンの設定については、メーカーのデータシートを参照してください。信号調整やアンプ回路に最適です。
詳細なピン配置データはありません: AD626ANZ.
詳細は データシート をご参照ください。
主な用途
AD626ANZ の用途: 6 件s: Current-Shunt Measurement, Bridge-Sensor Signal Conditioning, Medical Instrumentation Front End, Low-Pass Differential Filter, Battery-Powered Data Acquisition, High-Common-Mode Sensor Interface.
Current-Shunt Measurement
The AD626ANZ fits current-shunt front ends where a small differential voltage appears across a resistor while both input nodes carry a much larger common-mode voltage. Its 100 dB common-mode rejection helps prevent the common-mode component from dominating the measured result, and the 2.5 mV input offset specification is important when shunt drops are small. The single-supply range of 2.4 V to 10 V supports compact industrial systems. Configure the amplifier for the required differential gain while checking that the shunt common-mode voltage remains inside the specified input range and that the output does not approach either supply rail.
おすすめ
Bridge-Sensor Signal Conditioning
A strain-gauge or resistive bridge produces a small differential output around a substantial bridge excitation common-mode voltage, making the AD626ANZ appropriate for extracting and filtering the bridge signal. The 100 dB common-mode rejection reduces sensitivity to common supply and excitation variations, while the 100 kHz gain bandwidth product is suitable for low-frequency force, pressure, and displacement measurements. Use the manufacturer's recommended resistor network and verify that the excitation-derived common-mode voltage does not exceed the amplifier's input range. The 8-pin PDIP format is particularly convenient for instrumentation prototypes requiring straightforward through-hole assembly.
おすすめ
Medical Instrumentation Front End
The AD626ANZ can condition small differential signals from biomedical electrodes and isolated sensor interfaces where common-mode pickup may exceed the wanted signal. Its 2.5 mV input offset and 100 dB common-mode rejection support low-level differential measurements, and operation from 2.4 V to 10 V can simplify portable equipment power architecture. The amplifier should be surrounded by suitable input protection because medical sensor inputs may require isolation and leakage considerations beyond the amplifier's basic signal specification. Confirm noise, accuracy, patient-safety requirements, and applicable regulatory approvals at the complete-system level.
おすすめ
Low-Pass Differential Filter
The AD626ANZ supports amplification and low-pass filtering of small differential voltages, matching noisy sensor channels that require both common-mode rejection and bandwidth limiting. Its 100 kHz gain bandwidth product leaves headroom for an external feedback network that shapes the final filter response, but the usable bandwidth decreases as closed-loop gain rises. Select feedback resistors and capacitors using the manufacturer's application guidance, and place the network close to the relevant pins to reduce unwanted coupling. Verify settling behavior and filter attenuation at the highest signal frequency expected in the measurement channel.
おすすめ
Battery-Powered Data Acquisition
The AD626ANZ is suitable for compact, battery-powered data-acquisition modules because it supports a 2.4 V minimum single supply and rejects common-mode noise without requiring dual rails. The low-cost differential architecture is useful when sampling sensors, resistive dividers, or remote measurement lines where unequal ground potentials would impair a single-ended amplifier. At low supply voltages, carefully verify input common-mode range, output swing, and the offset contribution of the selected gain network. The 8-pin PDIP package is also useful during prototype development, although a surface-mount variant would generally be preferred for a high-volume compact assembly.
おすすめ
High-Common-Mode Sensor Interface
The AD626ANZ is appropriate when a sensor produces a small differential voltage on top of a large common-mode potential, particularly in industrial current and voltage monitoring. Its stated input common-mode range of approximately 6 times positive supply minus 1 V provides design margin above ordinary signal levels, while the 100 dB common-mode rejection suppresses shared interference. This capability can reduce the need for a separate common-mode attenuation stage. The complete design must still verify that the calculated common-mode and differential signals stay within the data-sheet limits across supply tolerance, temperature range, and component variation.
おすすめ
おすすめ製品の概要
エンジニアリング参考データ: AD626ANZ — 比較、設計ガイダンス、コンプライアンス情報。
選定ガイド
代替品との比較
| パラメータ | この製品 | AD626AN | AD626BNZ |
|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP - same package | 8-pin PDIP - same package |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Product Type | True single-supply differential amplifier | Differential amplifier | Differential amplifier |
| Number of Amplifier Circuits | 1 circuit | 1 circuit | 1 circuit |
主な差別化要因
- Verified same-package replacement path (vs AD626AN)
- True single-supply operation from 2.4 V (vs AD626AN)
- Strong common-mode rejection for differential sensing (vs AD626BNZ)
設計ノート
Do not treat a high common-mode input voltage as permission to exceed the absolute maximum ratings. The manufacturer describes an input common-mode range of approximately 6 times positive supply minus 1 V, but supply tolerances, transient overshoot, and input protection currents must also be included in the design. Check the absolute-maximum table and use appropriate series resistance or clamping when the source can exceed the operating limits.
Confirm the output swing at the selected supply voltage before choosing a high closed-loop gain. A 2.4 V to 10 V single supply allows flexible rail selection, but the useful output range still depends on load current and the amplifier's output-capacitance stability requirements. Analyze the signal chain at both supply extremes and avoid operating the output close to either rail unless the manufacturer explicitly permits it.
Keep the differential input traces short, symmetrical, and away from switching nodes and high-current paths. Place the feedback network and any filtering components close to the amplifier pins to minimize parasitic capacitance and pickup. Because the AD626 is intended to reject common-mode voltage, unequal input routing or ground currents can reintroduce differential error; use a compact, symmetric layout and a quiet return path.
The 100 kHz gain bandwidth product imposes a gain-dependent bandwidth limit. For example, higher closed-loop gain reduces the frequency range over which the amplifier can respond accurately, so a shunt or bridge measurement requiring wide bandwidth should use a lower gain or a faster amplifier. Evaluate the complete transfer function, including the external filter network, rather than relying only on the nominal gain bandwidth product.
コンプライアンス情報
The available manufacturer product information does not directly state the requested environmental declarations. Automotive qualification is treated as not applicable because this is an industrial-style Analog Devices differential amplifier rather than an identified automotive-qualified variant.