AD626ANZ - Low-Cost Single-Supply Differential Amp | Analog Devices
MPN: AD626ANZ ✓ Hoạt độngAD626ANZ Tóm tắt
A differential amplifier measures the voltage difference between two input nodes while rejecting voltage common to both inputs. Within the broader semiconductor hierarchy, the AD626 is an operational-amplifier-based signal-conditioning IC, then an amplifier, then an analog integrated circuit used within data-acquisition and instrumentation systems. This category is especially useful when a sensor output is much smaller than the voltage shared by both sensor terminals.
The AD626ANZ supports a broad 2.4 V to 10 V single-supply operating range, allowing operation from low-voltage systems as well as conventional industrial rails. Its stated input offset voltage is 2.5 mV, its common-mode rejection is 100 dB, and its gain bandwidth product is 100 kHz. These characteristics make it suitable for current-loop measurements, bridge-amplifier interfaces, sensor conditioning, and low-frequency filtering.
The input common-mode range extends to approximately 6 times the positive supply minus 1 V, as stated by the manufacturer, allowing the amplifier to process signals above its supply voltage when the circuit polarity and operating conditions permit. This characteristic helps designers handle high-side sensing and current-shunt measurements without first reducing the common-mode voltage through additional active circuitry.
Typical applications include precision current measurement, industrial sensor interfaces, low-pass differential filters, medical instrumentation, and data-acquisition front ends. The 8-pin PDIP package is also suitable for through-hole prototyping and designs where a leaded package simplifies inspection and rework.
The principal design constraint is signal bandwidth: with a 100 kHz gain bandwidth product, the usable closed-loop bandwidth depends on the configured gain. Higher closed-loop gain reduces bandwidth and should be checked against the required filter response and settling behavior. Input and feedback resistors also determine practical accuracy and noise performance.
This page combines manufacturer operating limits, a package-specific drop-in assessment, and practical replacement guidance. It helps engineers distinguish a true pin-compatible replacement from merely similar instrumentation amplifiers that use different packages or gain architectures.
Bộ thay thế dễ dàng lắp đặt cho AD626ANZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
AD626AN
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD626BNZ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
AD626ANZ Tỷ lệ tối đa & tính chất điện
| Product Type | Single-supply differential amplifier |
| Number of Amplifier Circuits | 1 circuit |
| Single-Supply Operating Voltage | 2.4 V to 10 V |
| Dual-Supply Operating Voltage | ±1.2 V to ±6 V |
| Input Offset Voltage | 2.5 mV |
| Common-Mode Rejection | 100 dB |
| Gain Bandwidth Product | 100 kHz |
| Input Common-Mode Range | Approximately 6 × (+VS − 1 V) |
| Khoảng nhiệt độ hoạt động | -40 °C to 85 °C |
| Hộp | 8-pin PDIP |
| Kiểu lắp đặt | Through-hole |
| Single-Supply Compatibility | True single-supply operation |
| Differential Signal Capability | Amplification and low-pass filtering of small differential voltages |
| Common-Mode Rejection Function | Rejection of voltage common to both inputs |
| Trạng thái RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | not_applicable |
| Lead-Free Status | unknown |
| Halogen-Free Status | unknown |
Hướng dẫn cấu hình chân AD626ANZ 8-pin pdip
Cấu hình chân cho AD626ANZ (8-pin pdip gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho AD626ANZ.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AD626ANZ phù hợp cho 6 Áp dụngs: Current-Shunt Measurement, Bridge-Sensor Signal Conditioning, Medical Instrumentation Front End, Low-Pass Differential Filter, Battery-Powered Data Acquisition, High-Common-Mode Sensor Interface.
Current-Shunt Measurement
The AD626ANZ fits current-shunt front ends where a small differential voltage appears across a resistor while both input nodes carry a much larger common-mode voltage. Its 100 dB common-mode rejection helps prevent the common-mode component from dominating the measured result, and the 2.5 mV input offset specification is important when shunt drops are small. The single-supply range of 2.4 V to 10 V supports compact industrial systems. Configure the amplifier for the required differential gain while checking that the shunt common-mode voltage remains inside the specified input range and that the output does not approach either supply rail.
Được đề xuất
Bridge-Sensor Signal Conditioning
A strain-gauge or resistive bridge produces a small differential output around a substantial bridge excitation common-mode voltage, making the AD626ANZ appropriate for extracting and filtering the bridge signal. The 100 dB common-mode rejection reduces sensitivity to common supply and excitation variations, while the 100 kHz gain bandwidth product is suitable for low-frequency force, pressure, and displacement measurements. Use the manufacturer's recommended resistor network and verify that the excitation-derived common-mode voltage does not exceed the amplifier's input range. The 8-pin PDIP format is particularly convenient for instrumentation prototypes requiring straightforward through-hole assembly.
Được đề xuất
Medical Instrumentation Front End
The AD626ANZ can condition small differential signals from biomedical electrodes and isolated sensor interfaces where common-mode pickup may exceed the wanted signal. Its 2.5 mV input offset and 100 dB common-mode rejection support low-level differential measurements, and operation from 2.4 V to 10 V can simplify portable equipment power architecture. The amplifier should be surrounded by suitable input protection because medical sensor inputs may require isolation and leakage considerations beyond the amplifier's basic signal specification. Confirm noise, accuracy, patient-safety requirements, and applicable regulatory approvals at the complete-system level.
Được đề xuất
Low-Pass Differential Filter
The AD626ANZ supports amplification and low-pass filtering of small differential voltages, matching noisy sensor channels that require both common-mode rejection and bandwidth limiting. Its 100 kHz gain bandwidth product leaves headroom for an external feedback network that shapes the final filter response, but the usable bandwidth decreases as closed-loop gain rises. Select feedback resistors and capacitors using the manufacturer's application guidance, and place the network close to the relevant pins to reduce unwanted coupling. Verify settling behavior and filter attenuation at the highest signal frequency expected in the measurement channel.
Được đề xuất
Battery-Powered Data Acquisition
The AD626ANZ is suitable for compact, battery-powered data-acquisition modules because it supports a 2.4 V minimum single supply and rejects common-mode noise without requiring dual rails. The low-cost differential architecture is useful when sampling sensors, resistive dividers, or remote measurement lines where unequal ground potentials would impair a single-ended amplifier. At low supply voltages, carefully verify input common-mode range, output swing, and the offset contribution of the selected gain network. The 8-pin PDIP package is also useful during prototype development, although a surface-mount variant would generally be preferred for a high-volume compact assembly.
Được đề xuất
High-Common-Mode Sensor Interface
The AD626ANZ is appropriate when a sensor produces a small differential voltage on top of a large common-mode potential, particularly in industrial current and voltage monitoring. Its stated input common-mode range of approximately 6 times positive supply minus 1 V provides design margin above ordinary signal levels, while the 100 dB common-mode rejection suppresses shared interference. This capability can reduce the need for a separate common-mode attenuation stage. The complete design must still verify that the calculated common-mode and differential signals stay within the data-sheet limits across supply tolerance, temperature range, and component variation.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD626ANZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AD626AN | AD626BNZ |
|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP - same package | 8-pin PDIP - same package |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Product Type | True single-supply differential amplifier | Differential amplifier | Differential amplifier |
| Number of Amplifier Circuits | 1 circuit | 1 circuit | 1 circuit |
Bảo phân biệt quan trọng
- Verified same-package replacement path (vsAD626AN)
- True single-supply operation from 2.4 V (vsAD626AN)
- Strong common-mode rejection for differential sensing (vsAD626BNZ)
Ghi chú thiết kế
Do not treat a high common-mode input voltage as permission to exceed the absolute maximum ratings. The manufacturer describes an input common-mode range of approximately 6 times positive supply minus 1 V, but supply tolerances, transient overshoot, and input protection currents must also be included in the design. Check the absolute-maximum table and use appropriate series resistance or clamping when the source can exceed the operating limits.
Confirm the output swing at the selected supply voltage before choosing a high closed-loop gain. A 2.4 V to 10 V single supply allows flexible rail selection, but the useful output range still depends on load current and the amplifier's output-capacitance stability requirements. Analyze the signal chain at both supply extremes and avoid operating the output close to either rail unless the manufacturer explicitly permits it.
Keep the differential input traces short, symmetrical, and away from switching nodes and high-current paths. Place the feedback network and any filtering components close to the amplifier pins to minimize parasitic capacitance and pickup. Because the AD626 is intended to reject common-mode voltage, unequal input routing or ground currents can reintroduce differential error; use a compact, symmetric layout and a quiet return path.
The 100 kHz gain bandwidth product imposes a gain-dependent bandwidth limit. For example, higher closed-loop gain reduces the frequency range over which the amplifier can respond accurately, so a shunt or bridge measurement requiring wide bandwidth should use a lower gain or a faster amplifier. Evaluate the complete transfer function, including the external filter network, rather than relying only on the nominal gain bandwidth product.
Thông tin tuân thủ
The available manufacturer product information does not directly state the requested environmental declarations. Automotive qualification is treated as not applicable because this is an industrial-style Analog Devices differential amplifier rather than an identified automotive-qualified variant.