ADM231LJRZ - 5V Dual RS-232 Transceiver | Analog Devices
MPN: ADM231LJRZ ✗ اختتامِ زندگیADM231LJRZ جائزہ
An RS-232 transceiver is an interface IC that converts between logic-level signals and the bipolar voltage levels used by RS-232 equipment. It belongs to the interface IC category and combines line drivers, line receivers, and charge-pump voltage support into one integrated component. The ADM231L is specifically positioned for low-power, +5 V systems where the RS-232 port must conserve board area and supply current.
The principal features are a single 5 V supply, two RS-232 drivers, two RS-232 receivers, CMOS-compatible logic inputs, and operation at data rates up to 100 kbps. The 16-pin SOIC package supports conventional surface-mount assembly and provides enough pins for power, ground, driver outputs, receiver inputs, and control functions. The manufacturer identifies the ADM231L family as obsolete, so new designs should account for lifecycle risk rather than treating it as an unrestricted new-production choice.
The multi-channel architecture allows one IC to serve a port containing both transmit and receive paths. This can reduce component count compared with using separate single-channel RS-232 devices. The 100 kbps capability is suitable for data acquisition, industrial control, instrumentation, and legacy peripheral connections where moderate-speed serial transfer is sufficient, although it does not target high-speed differential serial protocols.
Typical uses include industrial serial controllers, test and measurement equipment, point-of-sale systems, data-logging equipment, and embedded systems that retain an RS-232 interface. In each case, the two transmitters can carry outbound control or measurement data, while the two receivers can accept status information or commands from a remote terminal.
Design the surrounding interface carefully because RS-232 is a single-ended, bipolar system rather than a logic-level UART connection. Check voltage levels, grounding, cable length, and protection requirements in the application circuit. Allow suitable bypass capacitance at the +5 V supply pins and route interface traces away from noisy switching nodes to reduce data errors.
This page combines the manufacturer lifecycle information with package details, technical comparisons, and practical integration guidance. It also identifies when a current interface IC or a same-family replacement should be considered, helping engineers evaluate ADM231LJRZ against modern design requirements without overlooking its obsolete status.
کے لیے ڈراپ اِن متبادل ADM231LJRZ — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
ADM231LARZ
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ADM231AARZ
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ADM232LARZ
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ADM232AARZ
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ADM237LJRZ
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ADM231LJRZ تفصیلات
| Product Type | Low-power RS-232 transceiver |
| سپلائی وولٹیج | +5 V |
| Driver Channels | 2 channels |
| Receiver Channels | 2 channels |
| Maximum Data Rate | 100 kbps |
| پیکیج | 16-pin wide SOIC |
| پن کی تعداد | 16 pins |
| ماؤنٹنگ ٹائپ | Surface mount |
| Technology | CMOS |
| Power Class | Low power |
| لائف سائیکل کی حالت | Obsolete |
ADM231LJRZ 16-pin wide soic پن کنفیگریشن گائیڈ
ADM231LJRZ (16-pin wide soic پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں ADM231LJRZ.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
ADM231LJRZ کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Serial Controllers, Test and Measurement Equipment, Point-of-Sale Terminals, Data Loggers, Embedded Peripheral Interfaces, Legacy Equipment Repair.
Industrial Serial Controllers
The ADM231LJRZ fits legacy industrial controllers that exchange commands and status through an RS-232 port. Its 2 drivers and 2 receivers provide both transmit and receive paths on one +5 V IC, while the 100 kbps capability is suitable for moderate-speed command traffic and supervisory data. The 16-pin wide SOIC package simplifies repair and redesign work on boards that already use that footprint. Because the ADM231L family is obsolete, engineers should confirm temperature limits and pin functions in the Rev. C data sheet before releasing a new production design.
تجویز کردہ
Test and Measurement Equipment
Instrumentation systems can use the ADM231LJRZ to connect a controller or data-acquisition engine to a legacy RS-232 instrument. Two receivers allow status or measurement commands to enter the controller, while two drivers support outbound configuration and results. Its 100 kbps limit is appropriate for many serial measurement protocols and operator interfaces, and the single +5 V supply integrates cleanly with digital control hardware. Engineers should use the manufacturer data sheet for capacitor values, logic thresholds, and the exact receiver-enable arrangement rather than infer them from a generic RS-232 footprint.
تجویز کردہ
Point-of-Sale Terminals
The ADM231LJRZ is applicable to legacy point-of-sale equipment where a compact +5 V serial port connects a terminal, printer, or customer-display controller. Four channels allow bidirectional communication without separate line-driver and receiver packages, reducing PCB component count. The device's 100 kbps capability suits short control and transaction-status messages rather than high-volume data transfer. For maintained retail systems, preserve the original 16-pin layout and verify signal levels, grounding, and cable protection. For new terminals, evaluate the lifecycle status before approving an obsolete transceiver for another product cycle.
تجویز کردہ
Data Loggers
A data logger can use the ADM231LJRZ to communicate configuration commands and captured records with a host computer over RS-232. The two transmitters support outbound commands or status, and the two receivers accept host acknowledgments or setup data. At up to 100 kbps, the interface is suitable for many short-record control applications, provided the protocol does not require faster throughput. The +5 V CMOS implementation can simplify integration with digital logic, but field deployments should also address transient protection, ground potential differences, and long cable runs according to the application circuit in the manufacturer data sheet.
تجویز کردہ
Embedded Peripheral Interfaces
The ADM231LJRZ can connect an embedded controller to legacy printers, programmers, scanners, or service ports that use RS-232. Its combined driver and receiver arrangement supports full-duplex communication while preserving a conventional 16-pin wide SOIC footprint on existing boards. The 100 kbps rate is sufficient for many control-oriented peripheral protocols. Logic-side signals use the device's CMOS interface, while the cable side requires correct RS-232 levels and grounding. Validate the connector, protection network, and firmware framing in the target system because logical compatibility alone does not guarantee protocol compatibility.
تجویز کردہ
Legacy Equipment Repair
The ADM231LJRZ is especially relevant to maintenance and repair of equipment designed around the original 16-pin ADM231L footprint. Retaining the known +5 V supply architecture, 2-driver and 2-receiver arrangement, and 100 kbps interface avoids board redesign when replacing a failed IC in a qualified assembly. During repair, inspect the original device markings, verify that no shutdown or enable functions were added by later board revisions, and compare the replacement part's pin description with the installed footprint. Obsolete-product handling should include traceability, visual inspection, and electrical testing before the board returns to service.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا ADM231LJRZ — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | ADM231LARZ | ADM231AARZ | ADM232LARZ | ADM232AARZ | ADM237LJRZ |
|---|---|---|---|---|---|---|
| Package | 16-pin wide SOIC | 16-pin wide SOIC | 16-pin wide SOIC | 16-pin wide SOIC | 16-pin wide SOIC | 16-pin wide SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Supply Voltage | +5 V | +5 V | +5 V | +5 V | +5 V | +5 V |
| Driver Count | 2 drivers | 2 drivers | 2 drivers | 2 drivers | 2 drivers | 2 drivers |
| Receiver Count | 2 receivers | 2 receivers | 2 receivers | 2 receivers | 2 receivers | 2 receivers |
| Maximum Data Rate | 100 kbps | 100 kbps | 100 kbps | 100 kbps | 100 kbps | 100 kbps |
| Technology | +5 V CMOS | +5 V CMOS | +5 V CMOS | +5 V CMOS | +5 V CMOS | +5 V CMOS |
اہم امتیازی خصوصیات
- Combines four RS-232 line functions in one 16-pin device (بمقابلہMAX3221IPWR)
- Supports a moderate-speed data rate of 100 kbps (بمقابلہADM232LARZ)
- Uses the established 16-pin wide SOIC footprint (بمقابلہADM237LJRZ)
ڈیزائن نوٹس
Do not treat every member of the ADM23x family as automatically interchangeable. The ADM231L, ADM232L, and ADM237L can share a 16-pin SOIC format while differing in auxiliary control behavior. Before replacing the ADM231LJRZ, compare the pin-description table, enable or shutdown state, receiver outputs, logic thresholds, and temperature grade. A matching footprint protects the PCB mechanically but does not by itself prove electrical or functional compatibility.
Follow the +5 V connection and bypass recommendations in the manufacturer data sheet when laying out the ADM231LJRZ. Place the required decoupling capacitor close to the supply pin and ground return to suppress logic-side and line-driver supply noise. The RS-232 drivers use charge-pump-generated levels, so inadequate local decoupling can reduce signal integrity even when the external supply voltage is correct.
Keep RS-232 driver outputs away from sensitive receiver inputs and unrelated high-speed logic. Route the connector-side traces directly to the device, maintain the data sheet's ground arrangement, and place any external protection network where it can clamp cable transients without forcing large surge currents through the IC. Check the assembled orientation and lead numbering against the Rev. C pin-configuration drawing before power-up.
The ADM231LJRZ is a low-power interface IC, but its total dissipation still depends on supply voltage, driver loading, and ambient temperature. Check the driver-load conditions and logic-state dissipation in the family data sheet rather than estimating from quiescent current alone. Use normal SOIC copper guidance, preserve airflow around the device, and avoid placing it next to a heat source that elevates the board temperature beyond the selected part's rating.
تعمیل کی معلومات
The manufacturer product page identifies the ADM231L family as obsolete but does not provide explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declarations for this ordering code.