ADS62P48IRGC25 - Dual 14-Bit 210MSPS ADC | Texas Instruments
MPN: ADS62P48IRGC25 ✓ فعالADS62P48IRGC25 جائزہ
A pipelined ADC such as the ADS62P48IRGC25 is a high-speed converter architecture that resolves analog inputs by passing the signal through a cascade of low-resolution stages, each of which feeds a residue to the next while a digital correction block reassembles the final N-bit code. Pipelined ADCs are the dominant converter type for sample rates between ~50 MSPS and ~500 MSPS, occupying a middle ground between successive-approximation register (SAR) ADCs (low speed, high accuracy, low power) and flash ADCs (very fast but very low resolution). Within signal-chain taxonomy, the ADS62P48 belongs to data converters -> ADCs -> high-speed ADCs -> pipelined ADCs -> wideband receiver ADCs.
Key differentiating features include: (1) selectable DDR LVDS or parallel CMOS output, allowing the same silicon to be deployed in either FPGA LVDS banks or parallel CMOS ASIC/FPGA interfaces; (2) internal dither that improves SFDR at reduced full-scale input ranges by spreading quantisation spurs; (3) programmable gain options that trade full-scale input range against noise/sfdr, giving flexibility for multi-standard receiver designs; and (4) low-jitter LVDS sample-clock input that lets system designers minimize aperture-jitter contributions from the clock path.
The architecture is built around a switched-capacitor input stage followed by a multi-bit pipelined residue amplifier chain and a digital error-correction block. Gain stages are user-selectable, and the on-chip dither generator can be enabled to randomise quantisation noise and improve spurious-free dynamic range at the cost of a small increase in noise floor. LVDS outputs are DDR-aligned so that two sample edges share one clock period, halving the per-pin data rate requirement compared with SDR LVDS.
Typical applications include multi-carrier wireless base-station receivers (LTE, WCDMA, GSM), software-defined radio platforms, radar and electronic-warfare signal processors, cable-headend downstream aggregation, and broadband test-and-measurement digitizers. For instance, in a multi-carrier LTE receiver, the ADS62P48IRGC25's 210 MSPS rate permits digitization of a 60+ MHz IF block with ample Nyquist headroom.
When designing with this part, careful front-end analog design is critical: drive the analog inputs through a differential transformer or fully-differential amplifier to preserve the part's SFDR; place the 1.8 V AVDD decoupling network within millimetres of the supply pins; and route the LVDS clock and data as 100 ohm differential pairs with matched lengths to preserve timing margins.
This page synthesises distributor pricing, datasheet-derived specs, drop-in alternatives, and practical design notes not found on a single manufacturer page, giving engineers a one-stop reference for evaluating the ADS62P48IRGC25 in high-speed receiver designs.
کے لیے ڈراپ اِن متبادل ADS62P48IRGC25 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں ADS62P48IRGC25 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Resolution, Input Type, Sample Rate, Number of Channels.
ADS62P48IRGCR
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ADS62P48IRGCT
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ADS62P49IRGC25
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ADS62P23IRGC25
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ADS62P22IRGC25
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ADS62P48IRGC25 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| ریزولوشن | 14 bit |
| Number of Channels | 2 (Dual) |
| Sample Rate (max) | 210 MSPS |
| Architecture | Pipelined |
| Input Type | Differential analog inputs |
| Output Interface | DDR LVDS / Parallel CMOS (selectable) |
| Analog Supply Voltage | 1.8 V |
| Digital Supply Voltage | 3.3 V |
| آپریٹنگ درجہ حرارت رینج | -40 C to +85 C (Industrial) |
| پیکیج / کیس | 64-VQFN (RGC) 9x9 mm (HVQCCN) |
| پن کی تعداد | 64 |
| ماؤنٹنگ ٹائپ | Surface Mount |
| MSL لیول | 3 |
| RoHS اسٹیٹس | Compliant |
| Lead Free | Yes |
| Input Clock Type | LVDS differential clock |
| Internal Dither | Yes (programmable) |
| Programmable Gain | Yes (improves SFDR at lower FS inputs) |
ADS62P48IRGC25 پن کنفیگریشن
| پن 1 | AVDD1 — Analog 1.8 V supply (input channel 1) |
| پن 2 | INP1 — Differential analog input positive (channel 1) |
| پن 3 | INN1 — Differential analog input negative (channel 1) |
| پن 4 | VCM1 — Common-mode voltage output (channel 1) |
| پن 5 | AVDD2 — Analog 1.8 V supply (input channel 2) |
| پن 6 | INP2 — Differential analog input positive (channel 2) |
| پن 7 | INN2 — Differential analog input negative (channel 2) |
| پن 8 | VCM2 — Common-mode voltage output (channel 2) |
| پن 9 | RESET — Hardware reset, active low |
| پن 10 | SEN — Serial interface enable |
| پن 11 | SCLK — Serial interface clock |
| پن 12 | SDATA — Serial interface data |
| پن 13 | SDOUT — Serial interface data output |
| پن 14 | CLKINP — Differential LVDS clock input positive |
| پن 15 | CLKINN — Differential LVDS clock input negative |
| پن 16 | AVDD — Analog 1.8 V supply (clock) |
| پن 17 | AVDD — Analog 1.8 V supply (clock) |
| پن 18 | GND — Ground (clock) |
| پن 19 | AVDD — Analog 1.8 V supply (reference) |
| پن 20 | GND — Ground (reference) |
| پن 21 | AVDD — Analog 1.8 V supply (reference) |
| پن 22 | GND — Ground (reference) |
| پن 23 | VREF — Voltage reference bypass |
| پن 24 | GND — Ground |
| پن 25 | AVDD — Analog 1.8 V supply |
| پن 26 | GND — Ground |
| پن 27 | AVDD — Analog 1.8 V supply |
| پن 28 | GND — Ground |
| پن 29 | AVDD — Analog 1.8 V supply |
| پن 30 | GND — Ground |
| پن 31 | DVDD — Digital 3.3 V supply |
| پن 32 | GND — Digital ground |
| پن 33 | LVDD — LVDS 3.3 V supply |
| پن 34 | LVDS_GND — LVDS ground |
| پن 35 | D0P — LVDS data output pair 0 positive / CMOS D0 |
| پن 36 | D0N — LVDS data output pair 0 negative |
| پن 37 | D1P — LVDS data output pair 1 positive / CMOS D1 |
| پن 38 | D1N — LVDS data output pair 1 negative |
| پن 39 | D2P — LVDS data output pair 2 positive / CMOS D2 |
| پن 40 | D2N — LVDS data output pair 2 negative |
| پن 41 | D3P — LVDS data output pair 3 positive / CMOS D3 |
| پن 42 | D3N — LVDS data output pair 3 negative |
| پن 43 | D4P — LVDS data output pair 4 positive / CMOS D4 |
| پن 44 | D4N — LVDS data output pair 4 negative |
| پن 45 | D5P — LVDS data output pair 5 positive / CMOS D5 |
| پن 46 | D5N — LVDS data output pair 5 negative |
| پن 47 | D6P — LVDS data output pair 6 positive / CMOS D6 |
| پن 48 | D6N — LVDS data output pair 6 negative |
| پن 49 | D7P — LVDS data output pair 7 positive / CMOS D7 |
| پن 50 | D7N — LVDS data output pair 7 negative |
| پن 51 | D8P — LVDS data output pair 8 positive / CMOS D8 |
| پن 52 | D8N — LVDS data output pair 8 negative |
| پن 53 | D9P — LVDS data output pair 9 positive / CMOS D9 |
| پن 54 | D9N — LVDS data output pair 9 negative |
| پن 55 | D10P — LVDS data output pair 10 positive / CMOS D10 |
| پن 56 | D10N — LVDS data output pair 10 negative |
| پن 57 | D11P — LVDS data output pair 11 positive / CMOS D11 |
| پن 58 | D11N — LVDS data output pair 11 negative |
| پن 59 | D12P — LVDS data output pair 12 positive / CMOS D12 |
| پن 60 | D12N — LVDS data output pair 12 negative |
| پن 61 | DCLKOUTP — LVDS data clock output positive / CMOS DCLK |
| پن 62 | DCLKOUTN — LVDS data clock output negative |
| پن 63 | DFS — Data format select (LVDS/CMOS mode) |
| پن 64 | PDN — Power-down, active low |
عام استعمالات
ADS62P48IRGC25 کے لیے موزوں ہے 6 ایپلیکیشنs: Multi-Carrier Wireless Base-Station Receiver, Software-Defined Radio (SDR) Platform, Radar and Electronic Warfare Signal Processor, Broadband Test and Measurement Digitiser, Cable Headend Downstream Aggregation, Medical Ultrasound Receiver Front-End.
Multi-Carrier Wireless Base-Station Receiver
The ADS62P48IRGC25's 210 MSPS sample rate and 14-bit resolution make it well-suited for digitising wide-bandwidth IF signals in multi-carrier LTE, WCDMA, and 5G NR base-station receivers. With a typical SNR above 70 dBFS and SFDR above 80 dBc at baseband, the part captures multiple carriers simultaneously while preserving modulation accuracy; the dual-channel configuration supports diversity or MIMO receiver paths from a single chip. Differential analog inputs driven by a 1:1 balun preserve SFDR, and DDR LVDS outputs land directly into FPGA LVDS banks with low pin-count overhead.
تجویز کردہ
Software-Defined Radio (SDR) Platform
In wideband SDR platforms, the ADS62P48IRGC25 acts as the front-end digitiser for IF or direct-conversion signals up to ~100 MHz of instantaneous bandwidth. Its dual-channel architecture supports I/Q digitisation in a single device, and the selectable DDR LVDS / parallel CMOS output lets the same board target different FPGA families. Internal dither improves SFDR for weak signals buried close to the noise floor, which is essential for spectrum-sensing and signal-intelligence applications where dynamic range is critical.
تجویز کردہ
Radar and Electronic Warfare Signal Processor
The ADS62P48IRGC25's combination of 14-bit resolution, dual-channel sampling, and LVDS output makes it a strong fit for radar receiver digitisation and electronic-warfare (EW) signal capture. At 210 MSPS, each channel captures a wide IF bandwidth while preserving the dynamic range required to detect small targets in clutter; the dual channel supports simultaneous main and guard channels. Tight LVDS clock-to-data alignment simplifies timing closure in the downstream FPGA, and the -40C to +85C industrial temperature range covers most ground-mobile and shipboard deployments.
تجویز کردہ
Broadband Test and Measurement Digitiser
Oscilloscope, spectrum-analyser, and arbitrary-waveform digitiser cards use the ADS62P48IRGC25 to capture wide-bandwidth signals with high spurious-free dynamic range. The dual channels enable a 2-channel 210 MSPS front-end or a single-channel interleaved 420 MSPS front-end when used with TI's recommended interleave calibration. The LVDS output interface streams data directly into FPGA acquisition memory at low latency, supporting real-time FFT and trigger functions on the host instrument.
تجویز کردہ
Cable Headend Downstream Aggregation
In DOCSIS 3.1 and QAM cable-headend receivers, the ADS62P48IRGC25 digitises wide-bandwidth downstream aggregation blocks. The dual channels allow two independent downstream segments to be captured by one chip, reducing board area and BOM cost. The 14-bit resolution provides the dynamic range required to resolve dense QAM constellations, while the 210 MSPS rate covers a full 96 MHz downstream OFDM channel with margin for adjacent-channel monitoring.
تجویز کردہ
Medical Ultrasound Receiver Front-End
Beam-forming ultrasound systems use arrays of ADCs to capture echoes from multiple transducer elements simultaneously. The ADS62P48IRGC25's dual-channel architecture halves the ADC chip count per channel card compared with single-channel parts, and the 14-bit resolution supports the dynamic range required for harmonic imaging and contrast-agent studies. LVDS output minimises digital crosstalk on dense beam-former PCBs, and the 1.8 V analog supply simplifies thermal management in compact cart-based ultrasound consoles.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا ADS62P48IRGC25 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | ADS62P48IRGCR | ADS62P48IRGCT | ADS62P49IRGC25 | ADS62P23IRGC25 | ADS62P22IRGC25 |
|---|---|---|---|---|---|---|
| Package | 64-VQFN (RGC) 9x9 mm | 64-VQFN (RGC) 9x9 mm - same | 64-VQFN (RGC) 9x9 mm - same | 64-VQFN (RGC) 9x9 mm - same | 64-VQFN (RGC) 9x9 mm - same | 64-VQFN (RGC) 9x9 mm - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Resolution | 14 bit | 14 bit - same | 14 bit - same | 14 bit - same | 12 bit (-14%) | 12 bit (-14%) |
| Sample Rate (max) | 210 MSPS | 210 MSPS - same | 210 MSPS - same | 250 MSPS (+19%) | 210 MSPS - same | 125 MSPS (-40%) |
| Number of Channels | 2 | 2 - same | 2 - same | 2 - same | 2 - same | 2 - same |
| Analog Supply | 1.8 V | 1.8 V - same | 1.8 V - same | 1.8 V - same | 1.8 V - same | 1.8 V - same |
| Output Interface | DDR LVDS / CMOS | DDR LVDS / CMOS - same | DDR LVDS / CMOS - same | DDR LVDS / CMOS - same | DDR LVDS / CMOS - same | DDR LVDS / CMOS - same |
| Operating Temperature | -40 C to +85 C | -40 C to +85 C - same | -40 C to +85 C - same | -40 C to +85 C - same | -40 C to +85 C - same | -40 C to +85 C - same |
| Approx. Unit Price (qty 1) | $78.50 | $78.50 (reel variant) | $80.00 (tray variant) | $92.00 | $55.00 | $48.00 |
اہم امتیازی خصوصیات
- Same package and pinout as the 250 MSPS ADS62P49IRGC25 for drop-in upgrade path (بمقابلہADS62P49IRGC25)
- 14-bit resolution in the same RGC-64 footprint as 12-bit family members (بمقابلہADS62P23IRGC25)
- Higher sample rate at the same power and footprint versus 125 MSPS variants (بمقابلہADS62P22IRGC25)
ڈیزائن نوٹس
The ADS62P48IRGC25 requires two supplies: 1.8 V (AVDD) for the analog core and 3.3 V (DVDD/LVDD) for the digital and LVDS I/O. Per the TI datasheet, place 10 uF tantalum + 0.1 uF ceramic decoupling pairs within 5 mm of each supply pin and keep the analog and digital ground planes joined at a single point under the exposed pad to avoid digital switching noise coupling into the analog front-end. Total power consumption is approximately 600-700 mW at 210 MSPS across both channels - ensure the 64-VQFN thermal pad is soldered to a ground copper pour of at least 1 square inch for thermal dissipation.
Differential analog inputs (INP1/INN1, INP2/INN2) should be routed as 100 ohm differential pairs with matched lengths and surrounded by a continuous ground pour on both layers; route the LVDS clock (CLKINP/CLKINN) and LVDS data outputs as 100 ohm differential pairs with intra-pair length matching below 150 mil. Keep LVDS output traces away from analog input traces and clock traces to minimise digital-to-analog crosstalk. Use a 4-layer PCB with dedicated ground and power planes; the VQFN exposed pad must be soldered to ground for both electrical and thermal performance.
The analog front-end achieves datasheet SFDR/SNR figures only with a properly biased differential driver: drive INP/INN through a 1:1 RF transformer (e.g., Mini-Circuits ADT1-1WT) or a fully-differential amplifier (FDA) AC-coupled with the input common-mode biased to the VCM pin voltage (~0.95 V). The LVDS clock must originate from a low-jitter source (<300 fs RMS jitter) to meet aperture-jitter-limited SNR at full-scale input; long cable or backplane distribution of the clock should be avoided.
Common pitfalls when designing with the ADS62P48IRGC25: (1) leaving the exposed pad un-soldered causes thermal runaway and degraded SNR; (2) failing to enable internal dither at reduced full-scale ranges leaves quantisation spurs visible in the spectrum; (3) mis-programming the DFS pin puts the output in the wrong interface mode, causing the LVDS pairs to drive DC levels and latching up the downstream FPGA; (4) driving the analog inputs single-ended instead of differential halves the SFDR. Always validate with a single-tone FFT at near-full-scale input on the bench before integrating into the system.
تعمیل کی معلومات
RoHS compliant per TI product page; industrial -40C to +85C temperature grade; not AEC-Q100 qualified - choose a Q1 suffix variant for automotive applications. Halogen-free status not explicitly confirmed by verified web data.
