ATF16V8C-7PU - 7ns 300-Gate 16V8 SPLD PLD | Microchip Technology
MPN: ATF16V8C-7PU ✓ فعالATF16V8C-7PU جائزہ
A simple programmable logic device (SPLD) is a member of the programmable logic device family, sitting between fixed logic and mask-programmed PAL devices. Where a PAL must be sent to the mask vendor and a GAL/CPLD carries more silicon, an SPLD delivers a small, fixed macrocell array with three configurable operating modes selected automatically by the programming software. In the system hierarchy, an SPLD sits under PLD, under programmable logic, under integrated logic ICs.
Key features of the ATF16V8C-7PU include eight outputs each allocated eight product terms, three automatically configured modes of operation that allow highly complex logic functions, speeds down to 5 ns across the family, and a pin-controlled power-down mode in which supply current falls below 100 microamps. A pin-keeper circuit on each input and output holds the last valid state during power-down, so downstream logic does not see undefined levels on startup. All speed grades are specified over 5 V plus or minus 10 percent for industrial temperature range and 5 V plus or minus 5 percent for commercial range.
Technically, the device is a superset of the generic 16R8 architecture, which allows direct replacement of the 16R8 family and most 20-pin combinatorial PLDs. Eight outputs are each allocated eight product terms, and the pin arrangement accepts the conventional 16V8-style clock, feedback and output-enable assignments used by classic GAL/16V8 designs. The 7 ns speed grade means combinational paths resolve in roughly 7 ns, supporting clock rates near 70 MHz in registered configurations.
Typical applications include legacy 16V8 glue logic, address and control decoding in industrial control equipment, counter and state-machine logic in instrumentation, bus interface decoding in peripheral cards, and retrofits of older designs that need re-programmable logic without changing the board footprint.
When designing with the ATF16V8C-7PU, confirm that pin 4 is used as the power-down control input if low standby current is required; otherwise pin 4 may be used as an ordinary logic input. Use the pin description table in the manufacturer datasheet when assigning PCB tracks, and keep the 0.1 uF decoupling capacitor close to VCC pin 20.
This page consolidates drop-in replacement options, package and pinout details, and practical application guidance for the ATF16V8C-7PU that are not gathered together in the manufacturer datasheet.
کے لیے ڈراپ اِن متبادل ATF16V8C-7PU — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں ATF16V8C-7PU (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Device Type, Package, Propagation Delay, Supply Voltage, Architecture Compatibility.
ATF16V8C-10PU
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ATF16V8C-5PU
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PALCE16V8
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
GAL16V8
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PALCE16V8-10
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ATF16V8C-7PU زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Device Type | Simple Programmable Logic Device (SPLD), 16V8 family |
| Macrocell Count | 8 macrocells |
| Gate Count | 300 gates |
| Output Count | 8 outputs, 8 product terms each |
| Propagation Delay | 7 ns (ATF16V8C-7 speed grade) |
| Max Speed in Family | 5 ns |
| Technology | EECMOS electrically-erasable CMOS flash |
| میموری ٹائپ | Electrically Erasable (EE) Flash, non-volatile, in-circuit reprogrammable |
| سپلائی وولٹیج | 5 V +/- 10% industrial, 5 V +/- 5% commercial |
| Power-Down Mode | Pin-controlled, supply current below 100 uA |
| Power-Down Control Pin | Pin 4 |
| Pin-Keeper Circuits | Yes, on inputs and outputs |
| Modes of Operation | 3 modes configured automatically by software |
| Architecture Compatibility | Superset of generic 16R8, direct replacement for 16R8 and most 20-pin combinatorial PLDs |
| پیکیج | 20-pin PDIP (through-hole) |
| Temperature Grade | Industrial (-40C to +85C) |
| Finish | Green (lead-free) per part description |
| Manufacturer | Microchip Technology (Atmel heritage) |
| Programming | Standard SPLD programmer / Atmel-type PLD programming algorithm |
ATF16V8C-7PU پن کنفیگریشن
| پن 1 | CLK/IN — Clock input in registered mode, logic input otherwise |
| پن 2 | IN — Logic input |
| پن 3 | IN — Logic input |
| پن 4 | PD — Power-down control input; may be used as a logic input when power-down is not required |
| پن 5 | GND — Ground |
| پن 6 | OUT — Logic output |
| پن 7 | OUT — Logic output |
| پن 8 | NC — Not connected (per datasheet) |
| پن 9 | NC — Not connected (per datasheet) |
| پن 10 | NC — Not connected (per datasheet) |
| پن 11 | NC — Not connected (per datasheet) |
| پن 12 | NC — Not connected (per datasheet) |
| پن 13 | NC — Not connected (per datasheet) |
| پن 14 | GND — Ground |
| پن 15 | NC — Not connected (per datasheet) |
| پن 16 | NC — Not connected (per datasheet) |
| پن 17 | IN — Logic input |
| پن 18 | IN — Logic input |
| پن 19 | CLK/IN — Clock input in registered mode, logic input otherwise |
| پن 20 | VCC — Positive supply, 5 V |
عام استعمالات
ATF16V8C-7PU کے لیے موزوں ہے 6 ایپلیکیشنs: Legacy 16V8 Glue Logic for Board Revisions, Industrial Control Decode and State Logic, Instrumentation and Test Fixture Timing, Peripheral Card Bus Interface Decoding, Low-Power Handheld and Battery Equipment Logic, Programmable Counter, Divider, and State Machine Logic.
Legacy 16V8 Glue Logic for Board Revisions
The ATF16V8C-7PU is the natural fit when an existing 20-pin board must absorb a logic change without a respin. Because the device uses electrically-erasable flash memory, the same package can be reprogrammed in circuit or swapped with a programmed part, and the 7 ns propagation delay gives more timing margin than the older 10 ns and 15 ns SPLD families. The 20-pin PDIP footprint matches the standard 16V8 lead pattern, so existing footprints and pin assignments carry over. This makes the part a common choice for repairing and upgrading legacy instrumentation, test fixtures, and industrial control boards where the original PAL or GAL logic has been discontinued.
تجویز کردہ
Industrial Control Decode and State Logic
Control boards that decode address and control buses often need a compact, re-programmable block of decode logic with defined states during startup. The ATF16V8C-7PU provides 8 macrocells and 300 gates with 8 product terms per output, enough for address decode, interlock sequencing, and alarm latching in one device. Its pin-keeper circuits hold input and output levels through power-down so the downstream microcontroller does not read undefined pins during reset. The industrial temperature rating and 5 V plus or minus 10 percent supply window suit factory-floor equipment, and in-circuit flash re-programming allows the same board to serve several product variants.
تجویز کردہ
Instrumentation and Test Fixture Timing
Test and measurement fixtures often need fast, deterministic combinational paths to trigger measurement sequences and drive instrument control lines. The 7 ns propagation delay of the ATF16V8C-7PU supports register-clocked sequencing well beyond the rate that older 15 ns SPLDs could reach, while keeping the design in a single 20-pin through-hole device. The three automatically configured operating modes allow complex combinational and registered functions to be implemented in one part, reducing the number of discrete gates needed. For fixture makers replicating vintage instrument logic, the standard 16V8 pinout keeps hand-wired and socketed prototyping straightforward.
تجویز کردہ
Peripheral Card Bus Interface Decoding
Expansion cards in legacy computer and industrial peripheral systems frequently need address decode and chip-select logic that can be re-programmed across board revisions. The ATF16V8C-7PU implements the decode in a single 20-pin PDIP device with three software-selected modes, so one part can cover simple combinational decode, complex decode, or registered address latching. Its status as a superset of the generic 16R8 architecture means it can directly replace 16R8 and many 20-pin combinatorial PLDs already present in such designs. The 7 ns grade adds margin on marginal bus timing paths that originally used 10 ns or 15 ns devices.
تجویز کردہ
Low-Power Handheld and Battery Equipment Logic
Battery-operated and portable equipment benefits from a logic device that can be parked in a low-draw state between active measurement cycles. The ATF16V8C-7PU offers a pin-controlled power-down mode in which supply current falls below 100 microamps when pin 4 is driven high, and the pin-keeper circuits preserve the last valid logic state so the display, sensor front end, or radio is not disturbed by undefined levels on wake-up. Using the same 20-pin PDIP footprint as legacy designs allows a low-power redesign to drop into an existing through-hole layout without respinning the board.
تجویز کردہ
Programmable Counter, Divider, and State Machine Logic
Multi-stage counters, ripple dividers, and cyclic state machines map directly onto the ATF16V8C-7PU macrocell array. Eight outputs with eight product terms each give enough depth for a multi-bit counter with registered outputs, while the software-selected operating modes automatically apply the appropriate feedback structure during programming. The 7 ns propagation delay shortens the loop delay in ripple-carry counting compared with 10 ns and 15 ns SPLD grades, reducing the maximum count rate for a given design. Flash-based configuration also means a counter sequence or state table can be updated in the field without a socketed programmer or a factory trip.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا ATF16V8C-7PU — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | ATF16V8C-10PU | ATF16V8C-5PU | PALCE16V8 | GAL16V8 | PALCE16V8-10 |
|---|---|---|---|---|---|---|
| Package | 20-PDIP | 20-PDIP - same | 20-PDIP - same | 20-PDIP - same | 20-PDIP - same | 20-PDIP - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor |
| Macrocell / Gate Count | 8 macrocells / 300 gates | 8 macrocells / 300 gates | 8 macrocells / 300 gates | 16V8 family, 8 macrocells | 16V8 family, 8 macrocells | 16V8 family, 8 macrocells |
| Pin-Controlled Power-Down Mode | Yes, pin 4, supply current below 100 uA | Yes, pin 4, below 100 uA | Yes, pin 4, below 100 uA | Not available | Not available | Not available |
| Architecture Compatibility | Superset of generic 16R8, replaces most 20-pin combinatorial PLDs | Superset of generic 16R8 | Superset of generic 16R8 | 16V8 family architecture | 16V8 family architecture | 16V8 family architecture |
اہم امتیازی خصوصیات
- Faster propagation delay within the same 20-pin PDIP family footprint (بمقابلہATF16V8C-10PU)
- In-circuit re-programmability and low-power standby that legacy 16V8 devices lack (بمقابلہGAL16V8)
- Three software-selected operating modes and 16R8 superset compatibility (بمقابلہPALCE16V8)
ڈیزائن نوٹس
Pin 4 is a dual-function pin on the ATF16V8C family. If your design drives pin 4 high as a logic input, the device will interpret it as a power-down request and the supply current will drop below 100 microamps, which can starve the logic and cause erratic behaviour. Confirm the intended use of pin 4 from the pin description table in the manufacturer datasheet before layout, and reserve that net for a pull-down if the power-down feature is not used.
Place a 0.1 uF ceramic decoupling capacitor as close as possible to VCC (pin 20) with the ground return tied directly to the ground plane, and add a bulk capacitor near the supply source for the switching transients of nearby regulators. Because the ATF16V8C-7PU is specified across 5 V plus or minus 10 percent for industrial operation, verify the supply tolerance at the actual connector and connector pin, not just at the regulator output. In power-down mode the device draws under 100 microamps, so any residual leakage in the surrounding analog section can dominate the standby budget.
This is a through-hole 20-pin PDIP part, so fan-out and signal integrity are generally more forgiving than on a surface-mount PLD, but the clock and feedback nets still deserve controlled routing. Keep the pin 1 clock trace short and away from switching nodes and inductor loops, and route the ground leads (pins 5 and 14) directly to the ground plane rather than through a shared trace. Because the device is a superset of the generic 16R8 architecture, existing 20-pin footprints can be reused directly, so verify the DIP outline and lead pitch against the existing board rather than assuming a drop-in mechanical fit.
Estimated power figure for planning only: at the worst-case 5.5 V supply with all eight outputs driving low-impedance loads, the internal logic dissipation is typically under 100 mW, so no heat sink is required in this through-hole package. The larger thermal concern in most designs is the surrounding system, not the PLD itself. In power-down mode the supply current falls below 100 microamps, and the pin-keeper circuits hold the last valid state on inputs and outputs, so downstream logic will not see undefined levels during power cycling.
تعمیل کی معلومات
Part listings describe the ATF16V8C-7PU as green (lead-free) finish in a 20-pin PDIP industrial package. RoHS, REACH, halogen-free and conflict-minerals statements are not stated on the manufacturer material and are therefore recorded as unknown. AEC-Q100 qualification is not applicable to this industrial-grade PLD.