ATF16V8CZ-12JX - 12ns 8-Macrocell PLD | Microchip
MPN: ATF16V8CZ-12JX ✓ فعالATF16V8CZ-12JX جائزہ
An EEPLD, or electrically erasable programmable logic device, combines programmable AND-array logic, OR-array logic, and output macrocells in a reusable CMOS semiconductor. Its position in the logic hierarchy is EEPLD to SPLD to programmable logic device to integrated logic IC. The ATF16V8CZ architecture extends the capabilities of 16R8 devices and most 20-pin combinatorial PLDs, allowing one package to implement compact combinational or registered control logic.
The principal features include 12 ns maximum propagation delay, 25 µA standby power, zero-power operation, eight macrocells, and eight outputs allocated eight product terms each. Three operating modes are selected automatically by programming software. This combination supports interface decoding, address decoding, state-machine control, bus arbitration, and legacy PAL replacement while allowing the device to be reprogrammed rather than replaced for logic revisions.
Each output macrocell supports combinational, registered, or complex combinatorial operation, while eight dedicated input pins extend the total input capability to 16. The electrically erasable Flash-memory configuration permits repeated programming with dedicated software. CMOS- and TTL-compatible inputs and outputs facilitate use in mixed legacy systems, although designers should verify every external signal against the complete timing and electrical limits before finalizing a system.
Typical uses include peripheral control, industrial equipment, instrumentation, test systems, and small control subsystems where one PLCC can consolidate multiple gates. It is also appropriate for replacing compatible 16R8 and selected 20-pin combinatorial PLDs after confirming pinout, speed, power, and temperature requirements. A new design should also consider whether a current CPLD or FPGA provides useful additional capacity or features.
The principal design constraint is timing margin at the specified 12 ns speed grade. Treat 12 ns as the maximum pin-to-pin delay rather than a guaranteed system settling time, and include external logic, interconnect, skew, and setup-and-hold requirements in the timing budget. Follow the manufacturer pin-assignment table and recommended decoupling guidance when laying out the PCB.
This product page combines the manufacturer device architecture, package and timing characteristics, substitution relationships, and practical selection guidance. It is intended to accelerate engineering review while making clear which parameters require final confirmation against the current Microchip documentation.
کے لیے ڈراپ اِن متبادل ATF16V8CZ-12JX — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں ATF16V8CZ-12JX (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Device Type, Package.
ATF16V8CZ-15JU
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ATF16V8CZ-12JU
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ATF16V8CZ-10JU
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ATF16V8CZ-12JC
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ATF16V8CZ-15JC
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ATF16V8CZ-12JX زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Device Type | High-performance electrically erasable programmable logic device |
| Maximum Pin-to-Pin Delay | 12 ns |
| سپلائی وولٹیج | 5 V |
| Macrocell Count | 8 macrocells |
| Gate Equivalent Count | 250 gates |
| Maximum Input Count | 16 inputs |
| Configurable I/O Count | 8 I/Os |
| Output Count | 8 outputs |
| Product Terms per Output | 8 product terms |
| Operating Modes | 3 automatically configured modes |
| Standby Power | 25 µA |
| Power Consumption | Zero power |
| Logic Compatibility | CMOS and TTL compatible |
| پیکیج | 20-pin J-lead PLCC, 9 mm x 9 mm |
| ماؤنٹنگ ٹائپ | Surface mount |
| Configuration Technology | Electrically erasable Flash memory |
ATF16V8CZ-12JX 20-pin j-lead plcc, 9 mm x 9 mm پن کنفیگریشن گائیڈ
ATF16V8CZ-12JX (20-pin j-lead plcc, 9 mm x 9 mm پیکیج) کے لیے پن کنفیگریشن۔ اس ڈیجیٹل IC میں GPIO، کمیونیکیشن انٹرفیس (UART، SPI، I2C) اور پاور پنز شامل ہیں۔ متبادل پن فنکشنز اور کنفیگریشن آپشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ ایمبیڈڈ سسٹم ڈیزائن اور PCB لے آؤٹ کے لیے ضروری۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں ATF16V8CZ-12JX.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
ATF16V8CZ-12JX کے لیے موزوں ہے 6 ایپلیکیشنs: Peripheral Interface Control, Address and Command Decoding, Industrial Equipment Sequencing, Legacy PAL and 16R8 Replacement, Test and Measurement Control, Bus Arbitration and Resource Control.
Peripheral Interface Control
The ATF16V8CZ-12JX fits compact peripheral-control blocks because its 8 macrocells can implement registered command, address, and handshake decoding while eight configurable I/Os support the external interface. Its 12 ns maximum pin-to-pin delay provides useful timing margin for moderate-speed control paths, and the 5 V operating supply matches many legacy TTL-compatible systems. The device is placed between a host bus and peripheral logic, with the programmed output macrocells controlling selects, enables, and status signals. The main design consideration is to evaluate the complete path through bus drivers, interconnect, and receiving logic rather than relying on the 12 ns device rating alone.
تجویز کردہ
Address and Command Decoding
ATF16V8CZ-12JX is well suited to decoding addresses, register selects, and system commands because eight output macrocells can be configured automatically by the programming software. Up to 16 inputs provide sufficient width for address and control signals, while the 12 ns speed class supports common low-to-moderate-speed processor and bus arrangements. In implementation, the device is programmed with the required Boolean equations and connected to the relevant bus lines and output enables. Engineers should calculate setup and hold requirements against the actual bus timing, and ensure unused I/O pins are terminated according to the manufacturer configuration guidance.
تجویز کردہ
Industrial Equipment Sequencing
The ATF16V8CZ-12JX can consolidate machine-control sequencing, interlock logic, and actuator-command decoding into one 8-macrocell device. Its electrically erasable configuration allows logic revisions without changing the PCB, and the 12 ns maximum delay supports deterministic control paths in equipment operating below demanding real-time frequencies. A practical circuit uses the programmable outputs to coordinate motors, relays, indicators, or measurement functions through external drivers. The X suffix grade, supply tolerance, operating-temperature range, and isolation requirements must be checked for each industrial installation before production release.
تجویز کردہ
Legacy PAL and 16R8 Replacement
ATF16V8CZ-12JX can replace many 16R8-family and 20-pin combinatorial PLD designs because its architecture is described as a superset of the generic 16R8 arrangement. Eight macrocells and eight outputs provide enough resources for small combinational and registered functions, while electrically erasable Flash memory permits updated equations for engineering corrections or product variants. Migration should begin with a pin-by-pin comparison against the original device and a check of edge-sensitive versus combinational behavior. If the original design operates beyond the 12 ns grade's timing capability, use the 10 ns family option instead of accepting less margin.
تجویز کردہ
Test and Measurement Control
The ATF16V8CZ-12JX is useful for small instrumentation control blocks that coordinate operating modes, range selects, relay commands, and status reporting. Eight programmable I/Os can handle several discrete controls, while the 12 ns delay avoids adding substantial propagation delay to moderate-speed measurement paths. It is typically programmed to implement a state-dependent command matrix and then connected to external relays, switches, amplifiers, or data-acquisition circuitry. Signal-integrity and grounding practices remain important because the PLD itself cannot compensate for long unprotected input routes, switching transients, or unsuitable external drive levels.
تجویز کردہ
Bus Arbitration and Resource Control
ATF16V8CZ-12JX can implement compact arbitration, ownership, and resource-enable logic for systems with a limited number of competing bus masters. The device's 8 macrocells and programmable outputs allow request, grant, busy, and interrupt functions to be consolidated, while the 12 ns speed class suits many asynchronous control schemes with sufficient external timing margin. In a typical circuit, request signals enter the PLD and generated grant signals control transceivers or downstream devices. Timing must be evaluated across the master, PLD, and target, including contention cases and recovery behavior before the logic is considered production-safe.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا ATF16V8CZ-12JX — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | ATF16V8CZ-15JU | ATF16V8CZ-12JU | ATF16V8CZ-10JU | ATF16V8CZ-12JC | ATF16V8CZ-15JC |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 20-PLCC (9x9) | 20-PLCC (9x9) | 20-PLCC (9x9) | 20-PLCC (9x9) | 20-PLCC (9x9) | 20-PLCC (9x9) |
| Maximum Pin-to-Pin Delay | 12 ns | 15 ns | 12 ns | 10 ns | 12 ns | 15 ns |
| Macrocell Count | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells | 8 macrocells |
| Gate Equivalent Count | 250 gates | 250 gates | 250 gates | 250 gates | 250 gates | 250 gates |
| Input Count | Up to 16 inputs | Up to 16 inputs | Up to 16 inputs | Up to 16 inputs | Up to 16 inputs | Up to 16 inputs |
| Output Count | 8 outputs | 8 outputs | 8 outputs | 8 outputs | 8 outputs | 8 outputs |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V | 5 V |
| Standby Current | 25 µA | 25 µA | 25 µA | 25 µA | 25 µA | 25 µA |
| Logic Interface Compatibility | CMOS and TTL compatible | CMOS and TTL compatible | CMOS and TTL compatible | CMOS and TTL compatible | CMOS and TTL compatible | CMOS and TTL compatible |
اہم امتیازی خصوصیات
- Faster speed class than the documented 15 ns substitute (بمقابلہATF16V8CZ-15JU)
- Same-speed 20-pin PLCC family options (بمقابلہATF16V8CZ-12JU)
- Additional timing margin for more demanding paths (بمقابلہATF16V8CZ-12JU)
ڈیزائن نوٹس
Treat the 12 ns maximum pin-to-pin delay as one component of the complete timing path. Add external driver delay, interconnect delay, skew, receiver setup time, and clock uncertainty before assigning a system operating frequency. For asynchronous handshakes, verify both hold and recovery requirements. The 10 ns ATF16V8CZ family option can add timing margin when the existing design operates close to the limits of the 12 ns grade.
Use the exact 20-pin PLCC pin-description table from the manufacturer documentation when assigning traces and programming the device. Place the decoupling capacitor close to the supply and ground pins, keep the path through the power loop short, and route clock and sensitive control inputs away from noisy switching nodes. Inspect the PLCC pad layout for solder bridges and verify assembly clearances before releasing the PCB.
Do not assume that mechanically similar ATF16V8CZ order codes are automatically equivalent. Confirm the speed grade, suffix-specific temperature rating, package code, and pin configuration for every substitution. A 12 ns and a 15 ns part differ by 25% in maximum propagation delay, which can break a design operating with limited timing margin. Validate the programmed function and all interface states on prototypes before production use.
The ATF16V8CZ-12JX operates from 5 V and specifies 25 µA standby current with zero-power operation when inactive. Provide local high-frequency bypass in addition to bulk supply capacitance and route return current without sharing long paths with switching loads. Verify active current and temperature rise in the final enclosure because external drivers and nearby circuitry can contribute more system heat than the PLD itself.
تعمیل کی معلومات
The manufacturer product page identifies a green package, but explicit RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified. The device is not presented as an automotive-qualified AEC-Q100 variant.