DS90CR286MTD - 28-Bit 66MHz LVDS Receiver | Texas Instruments
MPN: DS90CR286MTD ✗ اختتامِ زندگیDS90CR286MTD جائزہ
A channel-link receiver is an interface integrated circuit that terminates low-voltage differential signaling and reconstructs parallel logic data at the receiving end of a point-to-point link. In the electronic-component hierarchy, it is an interface IC, a data-conversion device, and a semiconductor. Its primary role is to connect a high-speed differential transmitter to a digital controller, processor, FPGA, or other parallel-logic receiver while maintaining a controlled signal path across the cable or PCB interface.
The defining electrical characteristics of the DS90CR286MTD are its 28-bit data width, 66 MHz operating clock, 3.3 V supply, and 462 Mbps per-channel data rate. It accepts four LVDS data inputs and provides 28 LVCMOS/LVTTL outputs in the 56-pin TSSOP package. The rising-edge data-strobe architecture allows the receiver to transfer parallel data on the designated clock edge. Industrial temperature-grade ordering information identifies the device for industrial equipment applications.
The receiver is intended for high-speed point-to-point links where parallel logic cannot be carried directly across the interconnect. Its differential inputs are suited to balanced cable or PCB channels because they reduce sensitivity to common-mode noise compared with single-ended transmission. The parallel LVCMOS/LVTTL output side is compatible with digital logic systems, although output timing, trace length, and termination details must be controlled at the board level.
Typical uses include industrial control systems, test equipment, instrumentation, embedded processors, communication modules, and FPGA or CPLD data interfaces. The 462 Mbps per-channel capability is particularly relevant when a system must transfer 28 parallel bits across a compact differential link. In a transmitter-receiver pair, the companion device supplies the corresponding serialized differential signals, while the DS90CR286MTD restores the parallel data bus for downstream logic.
Layout is a central engineering consideration because the difference between a correctly designed channel and a marginal one is often determined by controlled impedance, pair geometry, grounding, and return-path continuity. Place the receiver close enough to the link connector or transmitter to minimize the unterminated differential segment, maintain a continuous reference plane, and route the LVDS pair as a tightly coupled pair. The manufacturer data sheet should govern capacitor selection, connector pin assignments, and any recommended test or termination arrangements.
This product overview combines the device identity, electrical operating points, packaging information, application context, and replacement considerations with practical design guidance. It is intended to help engineers determine whether the DS90CR286MTD fits a 3.3 V, 66 MHz channel-link architecture before beginning PCB implementation or production sourcing.
کے لیے ڈراپ اِن متبادل DS90CR286MTD — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں DS90CR286MTD (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Product Type, Supply Voltage.
DS90CR285MTD
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →DS90CR287MTD
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →DS90CF386MTDX/NOPB
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
DS90C363MTD
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →DS90CR286AMTD/NOPB
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
DS90CR286MTD تفصیلات
| Device Type | 28-bit channel-link LVDS receiver |
| سپلائی وولٹیج | 3.3 V |
| Data Width | 28 bits |
| Transmit Clock Frequency | 66 MHz |
| Data Rate per LVDS Channel | 462 Mbps |
| Input Signal | LVDS |
| Output Signal | LVCMOS/LVTTL |
| Data Strobe Edge | Rising edge |
| Number of LVDS Data Inputs | 4 |
| پیکیج | 56-TSSOP |
| Total Pin Count | 56 pins |
| ماؤنٹنگ ٹائپ | Surface mount |
| Temperature Grade | Industrial |
DS90CR286MTD 56-tssop پن کنفیگریشن گائیڈ
DS90CR286MTD (56-tssop پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں DS90CR286MTD.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
DS90CR286MTD کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Control Data Links, FPGA Parallel Data Interfaces, Test and Measurement Equipment, Embedded Processor Communication, Video and Imaging Backplanes, Telecommunications and Network Modules.
Industrial Control Data Links
The DS90CR286MTD fits point-to-point industrial control links that need to move a 28-bit parallel bus across a balanced LVDS channel. Its 66 MHz transmit-clock capability corresponds to 462 Mbps per LVDS data channel, while the receiver reconstructs four differential data streams as 28-bit LVCMOS/LVTTL data. This arrangement is useful when a controller, I/O board, or remote module is separated by a cable or a long PCB interconnect. The industrial temperature grade supports equipment designed for controlled industrial environments. In a new design, verify the exact temperature limits, supply tolerances, termination arrangement, and timing budget against the manufacturer data sheet before release.
تجویز کردہ
FPGA Parallel Data Interfaces
The DS90CR286MTD can receive a wide parallel data bus from an LVDS transmitter when an FPGA or CPLD uses a transceiver or multi-channel I/O structure for board-to-board communication. Its 28-bit LVCMOS/LVTTL output provides direct logic-level data to the FPGA input bank, while four LVDS inputs preserve a balanced transport path for the associated channel link. At the 66 MHz operating point, each data channel carries 462 Mbps. The design should account for input-to-output timing, clock distribution, ground bounce, and simultaneous output switching. Confirm FPGA I/O voltage, interface timing, and channel-link electrical requirements before assigning the receiver to a specific logic bank.
تجویز کردہ
Test and Measurement Equipment
The DS90CR286MTD is suitable for instrumentation that transports a 28-bit measurement or control word between circuit sections using LVDS. The 462 Mbps per-channel rate provides headroom for synchronized parallel data, while differential signaling helps preserve signal integrity across longer internal cable runs or inter-board connections. In a test instrument, the receiver can place recovered parallel data into a capture buffer, FPGA, processor, or pattern-control circuit. Because measurement accuracy can be affected by data timing and ground noise, preserve a continuous reference plane and isolate high-current return paths from the receiver area. The manufacturer timing and layout recommendations should be applied before the acquisition channel is calibrated.
تجویز کردہ
Embedded Processor Communication
The DS90CR286MTD can provide the receive side of a high-speed link between an embedded processor or microcontroller system and a remote data-acquisition or communications module. The 28-bit parallel output suits processors with dedicated data buses, while the LVDS input side reduces susceptibility to common-mode noise encountered in industrial environments. At 66 MHz, the four differential data paths carry 462 Mbps each, allowing the link to carry a 28-bit word during each transfer interval. System partitioning should align the receiver clock and data strobe with the processor interface and prevent output-bus contention during reset. Confirm voltage compatibility, timing margins, and signal-integrity performance in the final design.
تجویز کردہ
Video and Imaging Backplanes
The DS90CR286MTD can support parallel data transport in imaging systems where a source module sends a 28-bit word over LVDS to a processing or display-control board. Its 462 Mbps per-channel operation provides sufficient bandwidth for synchronized pixel, control, or metadata streams when the receiving logic uses the documented 66 MHz clock arrangement. The receiver converts the differential signals into LVCMOS/LVTTL for local digital processing. Video designs must pay particular attention to deterministic latency, clock distribution, and simultaneous switching noise on the 28 output lines. Use matched pair routing, a continuous ground reference, and manufacturer-recommended interface components while validating the complete timing chain across source, cable, receiver, and processing logic.
تجویز کردہ
Telecommunications and Network Modules
The DS90CR286MTD can serve as a parallel-output receiver in network-interface and telecommunications modules that use LVDS backplanes or short-reach copper links. A four-channel differential receiver with a 28-bit output provides a bridge between a serializing transmitter and local routing, switching, or processing logic. The 66 MHz clock and 462 Mbps per-channel data rate are appropriate for control-plane, status, and data-parity traffic where low latency and deterministic transfers are important. Deployment into a specific module requires review of channel-link timing, common-mode limits, connector pinout, and ground-return design. The device should not be assumed to replace a standard Ethernet PHY or serializer, but it can support proprietary high-speed internal links where the associated TI transmitter is used.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا DS90CR286MTD — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | DS90CR285MTD | DS90CR287MTD | DS90CF386MTDX/NOPB | DS90C363MTD | DS90CR286AMTD/NOPB |
|---|---|---|---|---|---|---|
| Package | 56-TSSOP | 56-TSSOP | 56-TSSOP | 56-TSSOP | 56-TSSOP | 56-TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
اہم امتیازی خصوصیات
- Direct 28-bit parallel-to-LVDS link architecture (بمقابلہDS90CR285MTD)
- Established 3.3 V, 66 MHz channel-link operating point (بمقابلہDS90C363MTD)
- Same-package family option with matching 28-bit receiver function (بمقابلہDS90CR286AMTD/NOPB)
- Purpose-defined rising-edge data-strobe implementation (بمقابلہDS90CR287MTD)
ڈیزائن نوٹس
Route each LVDS differential pair as a coupled pair over a continuous reference plane, with the pair geometry and spacing kept consistent from transmitter to receiver. Avoid routing over plane splits, high-current switching nodes, or isolated return-path discontinuities. Keep the differential segment as short as practical and place the receiver near the connector or transmitter when the link contains exposed cable or board transitions.
Validate receiver operation with the manufacturer's recommended termination and test setup before finalizing the board. The 28 parallel LVCMOS/LVTTL outputs can produce simultaneous switching noise and ground bounce, so preserve a low-impedance return path and decouple the 3.3 V supply near the device. Check data timing against the 66 MHz clock arrangement and ensure every connected output has a valid state during reset.
Do not treat the DS90CR285MTD as an electrical substitute merely because it uses the same family and package designation; it is the complementary transmitter. Likewise, verify protocol and pin assignments for the DS90CR287MTD, DS90CF386MTDX/NOPB, and DS90C363MTD before changing an existing board. Because DS90CR286MTD is NRND, new designs should include lifecycle, sourcing, and second-source risk in the approval process.
Power the 3.3 V receiver rail from a source capable of handling both the receiver and its companion transmitter, including inrush and simultaneous switching effects. Use local high-frequency bypassing and a low-impedance ground connection to reduce supply disturbance on the parallel output bus. Confirm the data sheet's absolute maximum and recommended operating limits before connecting external equipment or powered cables.
تعمیل کی معلومات
The DS90CR286MTD is described as an industrial-temperature-grade interface IC. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer product page or current material-compliance documentation.