Texas Instruments

DS90CR286MTD - 28-Bit 66MHz LVDS Receiver | Texas Instruments

MPN: DS90CR286MTD ✗ پایان تولید
3.3 V Vdss 56-TSSOP Package 66 MHz Speed
حداقل سفارش: 1 |

DS90CR286MTD نمای کلی

Texas Instruments DS90CR286MTD is a 28-bit channel-link receiver that converts differential LVDS data into 28-bit LVCMOS/LVTTL data. It operates from a 3.3 V supply, supports a 66 MHz transmit clock, and handles 462 Mbps per LVDS data channel. The device is packaged in a 56-pin TSSOP and uses rising-edge data strobing.

A channel-link receiver is an interface integrated circuit that terminates low-voltage differential signaling and reconstructs parallel logic data at the receiving end of a point-to-point link. In the electronic-component hierarchy, it is an interface IC, a data-conversion device, and a semiconductor. Its primary role is to connect a high-speed differential transmitter to a digital controller, processor, FPGA, or other parallel-logic receiver while maintaining a controlled signal path across the cable or PCB interface.

The defining electrical characteristics of the DS90CR286MTD are its 28-bit data width, 66 MHz operating clock, 3.3 V supply, and 462 Mbps per-channel data rate. It accepts four LVDS data inputs and provides 28 LVCMOS/LVTTL outputs in the 56-pin TSSOP package. The rising-edge data-strobe architecture allows the receiver to transfer parallel data on the designated clock edge. Industrial temperature-grade ordering information identifies the device for industrial equipment applications.

The receiver is intended for high-speed point-to-point links where parallel logic cannot be carried directly across the interconnect. Its differential inputs are suited to balanced cable or PCB channels because they reduce sensitivity to common-mode noise compared with single-ended transmission. The parallel LVCMOS/LVTTL output side is compatible with digital logic systems, although output timing, trace length, and termination details must be controlled at the board level.

Typical uses include industrial control systems, test equipment, instrumentation, embedded processors, communication modules, and FPGA or CPLD data interfaces. The 462 Mbps per-channel capability is particularly relevant when a system must transfer 28 parallel bits across a compact differential link. In a transmitter-receiver pair, the companion device supplies the corresponding serialized differential signals, while the DS90CR286MTD restores the parallel data bus for downstream logic.

Layout is a central engineering consideration because the difference between a correctly designed channel and a marginal one is often determined by controlled impedance, pair geometry, grounding, and return-path continuity. Place the receiver close enough to the link connector or transmitter to minimize the unterminated differential segment, maintain a continuous reference plane, and route the LVDS pair as a tightly coupled pair. The manufacturer data sheet should govern capacitor selection, connector pin assignments, and any recommended test or termination arrangements.

This product overview combines the device identity, electrical operating points, packaging information, application context, and replacement considerations with practical design guidance. It is intended to help engineers determine whether the DS90CR286MTD fits a 3.3 V, 66 MHz channel-link architecture before beginning PCB implementation or production sourcing.

جایگزین‌های drop-in برای DS90CR286MTD — همان پکیج، سازگار پین‌به‌پین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.

گونه‌ها در این سری

مدل‌های هم‌سری که جایگزین مستقیم هستند برای DS90CR286MTD (همان فرم‌فاکتور و فوت‌پرینت) — متفاوت در Package, Product Type, Supply Voltage.

Texas Instruments
Package: 48-TSSOP, 0.240 inch (6.10 mm) width
Product Type: Programmable LVDS FPD-Link transmitter
مقایسه با DS90CR286MTD →
Texas Instruments
Package: 56-pin TSSOP
Product Type: LVDS 28-bit Channel Link transmitter
Supply Voltage: +3.3 V
مقایسه با DS90CR286MTD →

DS90CR285MTD

✅ جایگزین مستقیم
Texas Instruments
📦 56-TSSOP
28-bit Channel Link LVDS transmitter · 3.3 V · 66 MHz · 28 bits · LVCMOS/LVTTL · 4 differential streams · 1 differential stream · 5 LVDS links

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

DS90CR287MTD

✅ جایگزین مستقیم
Texas Instruments
📦 56-TSSOP
LVDS 28-bit Channel Link transmitter · +3.3 V · 85 MHz · 28 bits · LVCMOS/LVTTL · 4 differential data streams · 1 differential LVDS transmit-clock stream · Rising edge

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

DS90CF386MTDX/NOPB

✅ جایگزین مستقیم
📦 56-TSSOP
Related 56-pin LVDS interface device with different serial and parallel data characteristics; verify channel count and protocol behavior

📋 جایگزین مرجع (خارج از کاتالوگ)

DS90C363MTD

✅ جایگزین مستقیم
Texas Instruments
📦 56-TSSOP
Programmable LVDS FPD-Link transmitter · 3 V to 3.6 V · 3.3 V · 18 bits · 65 MHz · 1300 Mbps · 0.45 V · 3 drivers

برای قیمت تماس بگیرید

مشاهده دیتاشیت ←

DS90CR286AMTD/NOPB

✅ جایگزین مستقیم
📦 56-TSSOP
Same DS90CR286 receiver family and 28-bit 66 MHz architecture, with an alternative tape-and-reel ordering code and potentially different lead-free labeling

📋 جایگزین مرجع (خارج از کاتالوگ)

DS90CR286MTD مشخصات

Device Type 28-bit channel-link LVDS receiver
ولتاژ تغذیه 3.3 V
Data Width 28 bits
Transmit Clock Frequency 66 MHz
Data Rate per LVDS Channel 462 Mbps
Input Signal LVDS
Output Signal LVCMOS/LVTTL
Data Strobe Edge Rising edge
Number of LVDS Data Inputs 4
بسته‌بندی 56-TSSOP
Total Pin Count 56 pins
نوع نصب Surface mount
Temperature Grade Industrial

راهنمای پیکربندی پین DS90CR286MTD 56-tssop

پیکربندی پین برای DS90CR286MTD (پکیج 56-tssop). شماره‌گذاری پایه‌ها، عملکردها و نمودارهای اتصال در دیتاشیت سازنده تعریف شده است. برای footprint دقیق و دستورالعمل‌های لحیم‌کاری به آن مراجعه کنید.

نمودار پین‌آوت پکیج 56-tssop برای DS90CR286MTD

داده پین‌آوت تفصیلی موجود نیست برای DS90CR286MTD.

به دیتاشیت برای پیکربندی کامل پین‌ها.

کاربردهای معمول

DS90CR286MTD مناسب است برای 6 کاربردs: Industrial Control Data Links, FPGA Parallel Data Interfaces, Test and Measurement Equipment, Embedded Processor Communication, Video and Imaging Backplanes, Telecommunications and Network Modules.

🏭

Industrial Control Data Links

The DS90CR286MTD fits point-to-point industrial control links that need to move a 28-bit parallel bus across a balanced LVDS channel. Its 66 MHz transmit-clock capability corresponds to 462 Mbps per LVDS data channel, while the receiver reconstructs four differential data streams as 28-bit LVCMOS/LVTTL data. This arrangement is useful when a controller, I/O board, or remote module is separated by a cable or a long PCB interconnect. The industrial temperature grade supports equipment designed for controlled industrial environments. In a new design, verify the exact temperature limits, supply tolerances, termination arrangement, and timing budget against the manufacturer data sheet before release.

🖥️

FPGA Parallel Data Interfaces

The DS90CR286MTD can receive a wide parallel data bus from an LVDS transmitter when an FPGA or CPLD uses a transceiver or multi-channel I/O structure for board-to-board communication. Its 28-bit LVCMOS/LVTTL output provides direct logic-level data to the FPGA input bank, while four LVDS inputs preserve a balanced transport path for the associated channel link. At the 66 MHz operating point, each data channel carries 462 Mbps. The design should account for input-to-output timing, clock distribution, ground bounce, and simultaneous output switching. Confirm FPGA I/O voltage, interface timing, and channel-link electrical requirements before assigning the receiver to a specific logic bank.

📟

Test and Measurement Equipment

The DS90CR286MTD is suitable for instrumentation that transports a 28-bit measurement or control word between circuit sections using LVDS. The 462 Mbps per-channel rate provides headroom for synchronized parallel data, while differential signaling helps preserve signal integrity across longer internal cable runs or inter-board connections. In a test instrument, the receiver can place recovered parallel data into a capture buffer, FPGA, processor, or pattern-control circuit. Because measurement accuracy can be affected by data timing and ground noise, preserve a continuous reference plane and isolate high-current return paths from the receiver area. The manufacturer timing and layout recommendations should be applied before the acquisition channel is calibrated.

⚙️

Embedded Processor Communication

The DS90CR286MTD can provide the receive side of a high-speed link between an embedded processor or microcontroller system and a remote data-acquisition or communications module. The 28-bit parallel output suits processors with dedicated data buses, while the LVDS input side reduces susceptibility to common-mode noise encountered in industrial environments. At 66 MHz, the four differential data paths carry 462 Mbps each, allowing the link to carry a 28-bit word during each transfer interval. System partitioning should align the receiver clock and data strobe with the processor interface and prevent output-bus contention during reset. Confirm voltage compatibility, timing margins, and signal-integrity performance in the final design.

📺

Video and Imaging Backplanes

The DS90CR286MTD can support parallel data transport in imaging systems where a source module sends a 28-bit word over LVDS to a processing or display-control board. Its 462 Mbps per-channel operation provides sufficient bandwidth for synchronized pixel, control, or metadata streams when the receiving logic uses the documented 66 MHz clock arrangement. The receiver converts the differential signals into LVCMOS/LVTTL for local digital processing. Video designs must pay particular attention to deterministic latency, clock distribution, and simultaneous switching noise on the 28 output lines. Use matched pair routing, a continuous ground reference, and manufacturer-recommended interface components while validating the complete timing chain across source, cable, receiver, and processing logic.

🌐

Telecommunications and Network Modules

The DS90CR286MTD can serve as a parallel-output receiver in network-interface and telecommunications modules that use LVDS backplanes or short-reach copper links. A four-channel differential receiver with a 28-bit output provides a bridge between a serializing transmitter and local routing, switching, or processing logic. The 66 MHz clock and 462 Mbps per-channel data rate are appropriate for control-plane, status, and data-parity traffic where low latency and deterministic transfers are important. Deployment into a specific module requires review of channel-link timing, common-mode limits, connector pinout, and ground-return design. The device should not be assumed to replace a standard Ethernet PHY or serializer, but it can support proprietary high-speed internal links where the associated TI transmitter is used.

What is the DS90CR286MTD?
The DS90CR286MTD is a 28-bit channel-link receiver from Texas Instruments that converts four LVDS data streams into 28-bit LVCMOS/LVTTL data. According to the TI product page, it operates from 3.3 V, uses rising-edge data strobing, and supports a 66 MHz transmit clock. The device is ordered in a 56-pin TSSOP package and is intended for industrial-grade equipment.
What are the key specifications of DS90CR286MTD that engineers should know?
The DS90CR286MTD supports a 28-bit data width, 66 MHz transmit clock, and 462 Mbps data rate per LVDS channel while operating from 3.3 V. According to Texas Instruments, the receiver accepts LVDS differential inputs and outputs 28-bit LVCMOS/LVTTL logic. Its 56-pin TSSOP package and industrial temperature grade make it suitable for compact industrial and embedded interface assemblies.
How fast can DS90CR286MTD transfer data?
The DS90CR286MTD supports 462 Mbps of data per LVDS channel when operated with a 66 MHz transmit clock. The manufacturer identifies the device as a 28-bit rising-edge data-strobe channel-link receiver. This performance is suitable for transferring wide parallel buses between circuit boards, cable links, transmitters, processors, FPGAs, and other digital interface blocks.
What is the difference between DS90CR286MTD and DS90CR285MTD?
DS90CR286MTD and DS90CR285MTD belong to the same TI 3.3 V, 66 MHz channel-link family, but they perform complementary link functions. The DS90CR286MTD is the receiver that converts four LVDS streams into 28-bit LVCMOS/LVTTL data, while the DS90CR285 is the transmitter that converts parallel data into differential outputs. A complete link normally uses both devices.
What is the difference between DS90CR286MTD and DS90CR287MTD?
The DS90CR286MTD is a 28-bit, 66 MHz rising-edge channel-link receiver, while the DS90CR287MTD is a related device with different channel-link characteristics. TI lists both parts in the DS90CR285/DS90CR286 family documentation, and a published comparison identifies DS90CR287MTD as a candidate for replacement review. Confirm data width, clocking, supply voltage, and pin assignments in the manufacturer data sheet before substitution.
When should I choose DS90CR286MTD over DS90CR285MTD?
Choose the DS90CR286MTD when your design needs to receive four differential LVDS data channels and convert them into a 28-bit parallel LVCMOS/LVTTL bus. Choose the DS90CR285MTD when the design must serialize a 28-bit parallel bus into four LVDS outputs. In most point-to-point links, one receiver and one transmitter are used at opposite ends rather than selecting either part as a substitute.
Is DS90CR286MTD suitable for an industrial LVDS interface?
Yes, DS90CR286MTD is identified as an industrial-temperature-grade interface IC in a 56-pin surface-mount TSSOP package. Its 3.3 V supply, 66 MHz clock capability, and 462 Mbps per-channel operation suit industrial equipment, control cabinets, instrumentation, and embedded communications modules. Final qualification still requires checking the complete operating-temperature and compliance requirements of the finished system.
Where can I download the DS90CR286MTD datasheet PDF?
The official DS90CR286 datasheet is available through Texas Instruments at https://www.ti.com/lit/gpn/ds90cr286, and the device page is located at https://www.ti.com/product/DS90CR286. These manufacturer resources contain the electrical characteristics, ordering information, package details, and implementation guidance needed for schematic and layout review.
Where can I find the DS90CR286MTD pinout?
The DS90CR286MTD pinout is published in the Texas Instruments DS90CR286 data sheet and package drawing. Because the exact pin names and exposed-pad details must match the documented 56-TSSOP configuration, use the pin-description table and land-pattern information from the manufacturer documentation rather than relying on a generic TSSOP footprint drawing.
What is the best drop-in replacement for DS90CR286MTD?
The closest documented candidates are the DS90CR285MTD and DS90CR287MTD, but neither should be treated as an automatic drop-in replacement because one is a transmitter and the other has different channel-link characteristics. The published comparison data supports evaluating these choices, while final adoption requires confirmation of package, pinout, supply voltage, clocking, protocol behavior, and data width against the DS90CR286MTD data sheet.
Can DS90CR285MTD replace DS90CR286MTD in an existing PCB?
DS90CR285MTD should not be assumed to replace DS90CR286MTD because it is the complementary transmitter in the TI channel-link family rather than a receiver with identical behavior. Both are associated with 3.3 V, 66 MHz channel-link systems, but the signal direction and data interface differ. Verify every pin and the complete power, clock, data, and termination requirements before considering a board revision.
What can replace DS90CR286MTD?
Possible candidates identified for engineering review include DS90CR287MTD, DS90CF386MTDX/NOPB, and DS90C363MTD, while DS90CR285MTD remains the complementary family member rather than a direct receiver substitute. No candidate should be approved as a drop-in replacement without checking the exact pin configuration, channel count, data width, clocking mode, supply requirements, and LVDS receiver behavior.
Where can I buy DS90CR286MTD and check its price?
Use the Request a Quote form on this page to request the current price, stock position, minimum order quantity, and lead time for DS90CR286MTD. The form routes the request to XAIPART and avoids relying on a static price that can change with quantity, currency, lifecycle status, or availability. Confirm the exact 56-TSSOP ordering suffix when placing the request.
What is the lead time for DS90CR286MTD?
The current lead time for DS90CR286MTD should be requested through the Request a Quote form on this page. Lead time can vary with order quantity, package configuration, inventory position, and the product's NRND lifecycle status. For production planning, request a committed quantity schedule along with the current commercial quotation.
Is DS90CR286MTD in stock?
Current DS90CR286MTD availability should be confirmed through the Request a Quote form on this page. The device is listed as NRND, so designers should not base a new-production schedule on an assumed active lifecycle or unconfirmed stock position. Include required quantities, target delivery dates, and the required manufacturer packaging configuration in the request.

داده‌های مرجع مهندسی برای DS90CR286MTD — مقایسه، راهنمای طراحی و اطلاعات انطباق.

راهنمای انتخاب

Choose the DS90CR286MTD when the board needs the receive side of a four-channel LVDS link that converts into a 28-bit LVCMOS/LVTTL bus at 66 MHz. DS90CR286AMTD/NOPB is the closest family-oriented ordering option when its suffix and sourcing conditions are acceptable, but verify the package marking and procurement configuration. DS90CR285MTD belongs on the transmitting side of the link and is not a functional substitute for a receiver. Consider DS90CR287MTD, DS90CF386MTDX/NOPB, or DS90C363MTD only after checking data width, clocking, protocol, pinout, termination, and supply requirements. Because DS90CR286MTD is NRND, new designs should balance electrical fit against lifecycle risk, availability, qualification effort, and the availability of a production-approved alternative.

مقایسه با جایگزین‌ها

پارامتر این محصول DS90CR285MTD DS90CR287MTD DS90CF386MTDX/NOPB DS90C363MTD DS90CR286AMTD/NOPB
Package 56-TSSOP 56-TSSOP 56-TSSOP 56-TSSOP 56-TSSOP 56-TSSOP
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments

تفاوت‌های کلیدی

  • Direct 28-bit parallel-to-LVDS link architecture (در مقابلDS90CR285MTD)
  • Established 3.3 V, 66 MHz channel-link operating point (در مقابلDS90C363MTD)
  • Same-package family option with matching 28-bit receiver function (در مقابلDS90CR286AMTD/NOPB)
  • Purpose-defined rising-edge data-strobe implementation (در مقابلDS90CR287MTD)

یادداشت‌های طراحی

Route each LVDS differential pair as a coupled pair over a continuous reference plane, with the pair geometry and spacing kept consistent from transmitter to receiver. Avoid routing over plane splits, high-current switching nodes, or isolated return-path discontinuities. Keep the differential segment as short as practical and place the receiver near the connector or transmitter when the link contains exposed cable or board transitions.

Validate receiver operation with the manufacturer's recommended termination and test setup before finalizing the board. The 28 parallel LVCMOS/LVTTL outputs can produce simultaneous switching noise and ground bounce, so preserve a low-impedance return path and decouple the 3.3 V supply near the device. Check data timing against the 66 MHz clock arrangement and ensure every connected output has a valid state during reset.

Do not treat the DS90CR285MTD as an electrical substitute merely because it uses the same family and package designation; it is the complementary transmitter. Likewise, verify protocol and pin assignments for the DS90CR287MTD, DS90CF386MTDX/NOPB, and DS90C363MTD before changing an existing board. Because DS90CR286MTD is NRND, new designs should include lifecycle, sourcing, and second-source risk in the approval process.

Power the 3.3 V receiver rail from a source capable of handling both the receiver and its companion transmitter, including inrush and simultaneous switching effects. Use local high-frequency bypassing and a low-impedance ground connection to reduce supply disturbance on the parallel output bus. Confirm the data sheet's absolute maximum and recommended operating limits before connecting external equipment or powered cables.

اطلاعات انطباق

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
بدون سرب
Unknown
بدون هالوژن
Unknown
مواد معدنی درگیری
Unknown

The DS90CR286MTD is described as an industrial-temperature-grade interface IC. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer product page or current material-compliance documentation.

تاریخ تأیید داده‌ها: 2026-11-10 — داده‌ها توسط تیم مهندسی قطعات XAIPART تأیید و گردآوری شده است

جستجوهای مرتبط

DS90CR286MTD datasheet DS90CR286MTD pinout DS90CR286MTD datasheet pdf DS90CR286MTD specifications DS90CR286MTD equivalent DS90CR286MTD replacement DS90CR286MTD cross reference DS90CR286MTD vs DS90CR285MTD DS90CR286MTD 56-TSSOP footprint Texas Instruments DS90CR286MTD DS90CR286MTD price DS90CR286MTD stock DS90CR286 28-bit LVDS receiver DS90CR286 462 Mbps channel link DS90CR286MTD lead time

قطعات و اصطلاحات مرتبط

Texas Instruments DS90CR286MTD DS90CR286 DS90CR285MTD DS90CR287MTD DS90CF386MTDX/NOPB DS90C363MTD DS90CR286AMTD/NOPB LVDS LVCMOS LVTTL channel-link receiver interface IC data-conversion semiconductor 28-bit parallel bus four-channel differential data receiver 66 MHz transmit clock 462 Mbps per-channel data rate rising-edge data strobe 3.3 V interface power supply 56-TSSOP TSSOP package family surface-mount package industrial-temperature-grade IC point-to-point data link
استعلام قیمت سریع RFQ
جزئیات کامل را پر کنید — تیم فروش ما ظرف 24 ساعت پاسخ خواهد داد
شماره قطعه سازنده بسته‌بندی QTY قیمت هدف قیمت کل
✓
استعلام قیمت ارسال شد!

ظرف ۲۴ ساعت به ایمیل شما پاسخ خواهیم داد

1
درخواست قیمت ارسال شد
2
استعلام دریافت شد
3
سفارش ثبت شد
4
پرداخت
5
ارسال شد
6
تحویل داده شد
مشاهده جزئیات RFQ