DS90LT012AHMFX - 400 Mbps LVDS Receiver | Texas Instruments
MPN: DS90LT012AHMFX ✓ فعالDS90LT012AHMFX جائزہ
An LVDS receiver is a high-speed interface device that converts a small-amplitude differential voltage into a conventional logic-level output. LVDS belongs to the differential line-driver and receiver family within interface ICs, where low voltage swing, common-mode rejection, and reduced crosstalk support reliable data transfer over longer printed-circuit-board traces than many single-ended interfaces. The DS90LT012AH also includes an input line-termination resistor for point-to-point applications.
The principal features of the DS90LT012AHMFX are its operation above 400 Mbps, typical differential input sensitivity of 350 mV, and 3 V CMOS output operation. Its low-noise receiver architecture is intended to preserve signal integrity in systems operating at high data rates. The integrated termination also simplifies point-to-point links by reducing the need for a separate input termination network.
The DS90LT012AHMFX is a single-receiver device rather than a quad-channel LVDS receiver. It is therefore suited to compact point-to-point links where channel count is secondary to package size, low power dissipation, and high signaling rate. The SOT-23-5 form factor supports dense PCB placement, although high-speed routing still requires controlled impedance and minimized trace-length mismatch.
Typical applications include high-speed point-to-point backplanes, industrial control links, video and display interfaces, communications equipment, test and measurement systems, and embedded data links. In each case, the receiver can convert a low-voltage differential LVDS signal into a 3 V CMOS signal for subsequent digital processing. The companion DS90LV011AH is identified in the manufacturer material as an LVDS line driver.
A critical implementation consideration is maintaining a continuous reference plane and tightly matched differential routing beneath the receiver. The input termination resistor is intended for point-to-point use, so designers should confirm whether the chosen link topology requires it. Input and output paths should also be kept short and separated from switching-current loops to preserve the receiver’s low-noise benefit.
This page combines the manufacturer’s operating characteristics, package information, verified component listings, cross-reference findings, and practical PCB guidance. It also identifies the limitation of the available substitute search: the directly related candidates share the receiver package and electrical family, but no independent set of five distinct cross-brand drop-in receivers could be confirmed without risking an incorrect replacement recommendation.
کے لیے ڈراپ اِن متبادل DS90LT012AHMFX — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
DS90LT012AHMF/NOPB
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
DS90LT012AHMFX/NOPB
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
DS90LT012AHMFX تفصیلات
| Product Type | Single CMOS differential LVDS line receiver |
| Maximum Data Rate | Greater than 400 Mbps |
| زیادہ سے زیادہ کلاک فریکوئنسی | 200 MHz |
| Typical Differential Input Voltage | 350 mV |
| Output Voltage Level | 3 V CMOS |
| Receiver Quantity | 1 receiver |
| Input Termination | Integrated input line-termination resistor |
| پیکیج | SOT-23-5 |
| Terminal Count | 5 terminals |
| ماؤنٹنگ ٹائپ | Surface mount |
| Manufacturer Product Page | Texas Instruments DS90LT012AH product page |
DS90LT012AHMFX sot-23-5 پن کنفیگریشن گائیڈ
DS90LT012AHMFX (sot-23-5 پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں DS90LT012AHMFX.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
DS90LT012AHMFX کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial High-Speed Control Links, Communications Equipment Interconnects, Video and Display Data Channels, Test and Measurement Signal Paths, Embedded Processor and FPGA Links, Low-Power Serial Backplanes.
Industrial High-Speed Control Links
The DS90LT012AHMFX fits isolated industrial cabinet-to-cabinet or board-to-board control links that require a low-amplitude differential receiver. Its operation above 400 Mbps, typical 350 mV input, and 3 V CMOS output provide ample signaling margin for a compact point-to-point LVDS channel. The integrated input termination can simplify receiver-side matching, while the SOT-23-5 package preserves board area. Use controlled-impedance routing, matched differential lengths, and a continuous ground reference to prevent the 200 MHz-class clock signal from accumulating noise or timing distortion.
تجویز کردہ
Communications Equipment Interconnects
The DS90LT012AHMFX is suitable for compact high-speed links inside communications equipment where an LVDS transmitter is followed by a local receiver. Supporting data rates in excess of 400 Mbps allows the 200 MHz receiver to carry serial data, clock, or recovered signaling through a point-to-point PCB channel. Its low-noise CMOS output stage provides a direct interface to digital logic, while the integrated line termination reduces receiver-side network complexity. Route the pair over a continuous reference plane and keep connector or transceiver escape paths short to avoid impedance discontinuities.
تجویز کردہ
Video and Display Data Channels
The DS90LT012AHMFX can receive LVDS signaling used between video or display processing blocks when the link operates as a dedicated high-speed differential channel. Its typical 350 mV sensitivity and greater-than-400-Mbps capability suit the serial data rates commonly encountered in pixel-clock and video-data interfaces. The 3 V CMOS output can feed receiving logic, and the SOT-23-5 footprint supports placement near the source driver. The principal design constraint is signal integrity: maintain matched pair geometry, adequate return-path continuity, and separation from switching-power paths.
تجویز کردہ
Test and Measurement Signal Paths
The DS90LT012AHMFX is appropriate for receiving high-speed differential stimulus or clock signals in compact test and measurement instruments. Its low-noise receiver architecture is intended to preserve the integrity of signals passing above 400 Mbps, while the 3 V CMOS output can connect to counters, capture logic, or FPGA input stages. The integrated termination is useful for point-to-point fixture or board links, although cable and fixture transitions require careful impedance control. Keep the receiver away from fan drives, relays, and high-current switching nodes to minimize coupled noise.
تجویز کردہ
Embedded Processor and FPGA Links
The DS90LT012AHMFX can serve as the receiver endpoint for a short high-speed link between an FPGA or embedded controller and another board. At data rates in excess of 400 Mbps, it converts a typical 350 mV LVDS differential signal into a 3 V CMOS output suitable for digital logic. Its small SOT-23-5 package allows placement close to the destination device, reducing trace exposure. Designers should verify the companion driver’s output compatibility, termination arrangement, clock topology, and I/O voltage rather than assuming every LVDS and CMOS interface can be connected directly.
تجویز کردہ
Low-Power Serial Backplanes
The DS90LT012AHMFX is well suited to low-power serial backplanes where one point-to-point lane must carry data above 400 Mbps without the higher supply requirements of legacy ECL or PECL devices. The receiver’s low-power LVDS approach, typical 350 mV input, and integrated termination simplify board-level implementation. Each lane requires balanced routing and a suitable LVDS source, and the receiver output must match the destination device’s CMOS voltage. Validate timing budget, skew, connector transitions, and channel loss when the link extends beyond a PCB trace.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا DS90LT012AHMFX — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | DS90LT012AHMF/NOPB | DS90LT012AHMFX/NOPB |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOT-23-5 | SOT-23-5 - same package | SOT-23-5 - same package |
| Receiver Type | Single CMOS differential LVDS receiver | Single differential receiver | Single differential receiver |
| Input Termination | Integrated input line-termination resistor | Integrated input line-termination resistor | Integrated input line-termination resistor |
| Receiver Quantity | 1 receiver | 1 receiver | 1 receiver |
| Mounting Type | Surface mount | Surface mount | Surface mount |
اہم امتیازی خصوصیات
- Compact single-channel receiver (بمقابلہDS90LV012ATMF)
- Integrated point-to-point termination (بمقابلہDS90LV011AH)
- High-speed operation in a small package (بمقابلہDS90LT012AHMF/NOPB)
ڈیزائن نوٹس
Route the LVDS input as a tightly matched differential pair over a continuous reference plane. Maintain the intended characteristic impedance through the receiver pins, avoid stubs, and minimize vias because a discontinuity can create reflections that become significant when the interface operates at 200 MHz. Keep the receiver close to the destination logic and provide an uninterrupted ground-return path beneath the pair.
The integrated input termination is intended for point-to-point applications. Confirm that the PCB channel, source-driver impedance, and receiver termination form the intended network rather than adding a second termination that would over-damp the signal. Review input common-mode limits, receiver threshold behavior, and trace-length tolerance using the Texas Instruments DS90LT012AH datasheet before fixing the topology.
Do not substitute DS90LV012ATMF or DS90LV011AH as receiver replacements merely because they use a related SOT-23-5 package. The DS90LV012A parts are associated with the line-driver side of the interface family, so their signal direction and pin functions differ from the DS90LT012AH receiver. Verify the numbered pin table, power rails, termination arrangement, and logic-level compatibility for every proposed replacement.
Keep the high-speed receiver path away from switching-power inductors, relay contacts, high-di/dt traces, and connector transitions where possible. Route slow control and logic signals on a separate layer where practical, and provide local bypassing at the device supply pins. Although the receiver is designed for low noise, external common-mode and conducted noise can still affect the small 350 mV-typical differential signal.
تعمیل کی معلومات
The available component information identifies the exact MPN and package but does not provide extractable compliance statements. The NOPB ordering suffix should not be interpreted as proof of compliance without the corresponding manufacturer declaration.