EPM570GT100C3N - MAX II CPLD 440 Macrocells 76 I/O TQFP-100 | Intel
MPN: EPM570GT100C3N ✓ فعالEPM570GT100C3N جائزہ
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that sits in the hierarchy between simple SPLDs/PLDs and FPGAs. It uses a small AND/OR fabric (here, 440 macrocells arranged in Logic Array Blocks) to implement combinational and registered logic. Compared with FPGAs, CPLDs offer lower power, deterministic timing, and instant-on behavior. Within Intel's portfolio, the MAX II family occupies the glue-logic and control-plane role, sitting between the MAX 10 and the Cyclone series. The 'G' suffix indicates a 'Green' power variant of the original MAX II family.
Key features of the EPM570GT100C3N include 8 Kbits of user Flash memory, MultiVolt I/O supporting 1.5/1.8/2.5/3.3 V interfaces, bus-hold circuitry on user I/O, JTAG-based in-system programmability, and support for the Quartus II design software. The 100-pin TQFP package supports commercial operating junction temperature (0C to 85C). The 76 available user I/O pins (after subtracting JTAG, power, and dedicated configuration pins from the 100-pin count) are sufficient to interface multiple microcontrollers, bus bridges, and glue-logic functions in a single device.
The internal architecture combines a flash-based configuration store with a multi-level interconnect, four LABs feeding into macrocells with configurable flip-flops, and a JTAG-compliant boundary scan chain. This architecture yields deterministic 5.4 ns tPD regardless of logic utilization, a hallmark of CPLDs versus SRAM-based FPGAs. The MultiVolt core and I/O rails allow direct interfacing with 3.3 V MCUs and 1.8 V ASICs from a single chip.
Typical applications include bus-interface bridging (PCI to local bus, I2C/SPI multiplexing), I/O expansion for microcontrollers, power-sequencer and reset-controller logic, motor-control state machines, LED-display drivers, and industrial control glue logic. The instant-on behavior is favored in industrial automation where the controller must be ready within milliseconds of power-up.
A key design consideration is that 100-pin TQFP packages are hand-solderable and rework-friendly, unlike BGA variants in the same family. Designers migrating from the older MAX II to MAX II G should verify the VCCINT supply ramp and JTAG chain because, although pin-compatible, internal supply tolerances differ between the two revisions. This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the standalone datasheet.
کے لیے ڈراپ اِن متبادل EPM570GT100C3N — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں EPM570GT100C3N (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Operating Temperature, Package, Process Technology, Programming Interface, Mounting Type.
EPM570GT100C5N
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM570GT100C4N
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM570GT100I5N
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM570F100C5N
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →EPM570GT100C3N زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Family | MAX II |
| Series | MAX II G (Green) |
| Logic Elements | 570 |
| Macrocells | 440 |
| User I/O Pins | 76 |
| User Flash Memory | 8 Kbits |
| Propagation Delay (tPD max) | 5.4 ns |
| Core Voltage (VCCINT) | 1.71 V to 1.89 V (1.8 V typical) |
| I/O Voltage Standards | 1.5 V / 1.8 V / 2.5 V / 3.3 V (MultiVolt) |
| Process Technology | 0.18 um |
| آپریٹنگ درجہ حرارت | 0C to 85C (TJ, commercial) |
| پیکیج | 100-pin TQFP (14x14 mm) |
| ماؤنٹنگ ٹائپ | Surface Mount |
| Programmable Type | In-System Programmable (Flash, non-volatile) |
| Programming Interface | JTAG (IEEE 1149.1) / ISP |
| RoHS اسٹیٹس | Lead free / RoHS Compliant |
EPM570GT100C3N پن کنفیگریشن
| پن 1 | I/O — User I/O pin (bank 1) |
| پن 2 | I/O — User I/O pin (bank 1) |
| پن 3 | I/O — User I/O pin (bank 1) |
| پن 4 | I/O — User I/O pin (bank 1) |
| پن 5 | I/O — User I/O pin (bank 1) |
| پن 6 | I/O — User I/O pin (bank 1) |
| پن 7 | VCCIO1 — I/O bank 1 supply voltage |
| پن 8 | I/O — User I/O pin (bank 1) |
| پن 9 | I/O — User I/O pin (bank 1) |
| پن 10 | GND — Ground |
| پن 11 | I/O — User I/O pin (bank 1) |
| پن 12 | I/O — User I/O pin (bank 1) |
| پن 13 | I/O — User I/O pin (bank 1) |
| پن 14 | I/O — User I/O pin (bank 1) |
| پن 15 | TDI — JTAG Test Data In |
| پن 16 | TMS — JTAG Test Mode Select |
| پن 17 | TCK — JTAG Test Clock |
| پن 18 | I/O — User I/O pin (bank 2) |
| پن 19 | I/O — User I/O pin (bank 2) |
| پن 20 | I/O — User I/O pin (bank 2) |
| پن 21 | VCCINT — Core supply voltage (1.8 V) |
| پن 22 | GND — Ground |
| پن 23 | I/O — User I/O pin (bank 2) |
| پن 24 | I/O — User I/O pin (bank 2) |
| پن 25 | I/O — User I/O pin (bank 2) |
| پن 26 | I/O — User I/O pin (bank 2) |
| پن 27 | VCCIO2 — I/O bank 2 supply voltage |
| پن 28 | I/O — User I/O pin (bank 2) |
| پن 29 | I/O — User I/O pin (bank 2) |
| پن 30 | I/O — User I/O pin (bank 2) |
| پن 31 | GND — Ground |
| پن 32 | I/O — User I/O pin (bank 2) |
| پن 33 | I/O — User I/O pin (bank 2) |
| پن 34 | I/O — User I/O pin (bank 2) |
| پن 35 | I/O — User I/O pin (bank 2) |
| پن 36 | I/O — User I/O pin (bank 2) |
| پن 37 | I/O — User I/O pin (bank 2) |
| پن 38 | TDO — JTAG Test Data Out |
| پن 39 | I/O — User I/O pin (bank 2) |
| پن 40 | I/O — User I/O pin (bank 2) |
| پن 41 | GND — Ground |
| پن 42 | I/O — User I/O pin (bank 2) |
| پن 43 | VCCIO2 — I/O bank 2 supply voltage |
| پن 44 | I/O — User I/O pin (bank 2) |
| پن 45 | I/O — User I/O pin (bank 2) |
| پن 46 | I/O — User I/O pin (bank 2) |
| پن 47 | I/O — User I/O pin (bank 2) |
| پن 48 | I/O — User I/O pin (bank 3) |
| پن 49 | I/O — User I/O pin (bank 3) |
| پن 50 | VCCINT — Core supply voltage (1.8 V) |
| پن 51 | GND — Ground |
| پن 52 | I/O — User I/O pin (bank 3) |
| پن 53 | I/O — User I/O pin (bank 3) |
| پن 54 | I/O — User I/O pin (bank 3) |
| پن 55 | I/O — User I/O pin (bank 3) |
| پن 56 | VCCIO3 — I/O bank 3 supply voltage |
| پن 57 | I/O — User I/O pin (bank 3) |
| پن 58 | I/O — User I/O pin (bank 3) |
| پن 59 | I/O — User I/O pin (bank 3) |
| پن 60 | GND — Ground |
| پن 61 | I/O — User I/O pin (bank 3) |
| پن 62 | I/O — User I/O pin (bank 3) |
| پن 63 | I/O — User I/O pin (bank 3) |
| پن 64 | I/O — User I/O pin (bank 3) |
| پن 65 | I/O — User I/O pin (bank 3) |
| پن 66 | I/O — User I/O pin (bank 3) |
| پن 67 | I/O — User I/O pin (bank 3) |
| پن 68 | CONF_DONE — Configuration done (open-drain) |
| پن 69 | nSTATUS — Configuration status (open-drain) |
| پن 70 | I/O — User I/O pin (bank 4) |
| پن 71 | GND — Ground |
| پن 72 | I/O — User I/O pin (bank 4) |
| پن 73 | VCCIO4 — I/O bank 4 supply voltage |
| پن 74 | I/O — User I/O pin (bank 4) |
| پن 75 | I/O — User I/O pin (bank 4) |
| پن 76 | I/O — User I/O pin (bank 4) |
| پن 77 | I/O — User I/O pin (bank 4) |
| پن 78 | VCCINT — Core supply voltage (1.8 V) |
| پن 79 | GND — Ground |
| پن 80 | I/O — User I/O pin (bank 4) |
| پن 81 | I/O — User I/O pin (bank 4) |
| پن 82 | I/O — User I/O pin (bank 4) |
| پن 83 | I/O — User I/O pin (bank 4) |
| پن 84 | VCCIO4 — I/O bank 4 supply voltage |
| پن 85 | I/O — User I/O pin (bank 4) |
| پن 86 | I/O — User I/O pin (bank 4) |
| پن 87 | I/O — User I/O pin (bank 4) |
| پن 88 | GND — Ground |
| پن 89 | I/O — User I/O pin (bank 4) |
| پن 90 | I/O — User I/O pin (bank 4) |
| پن 91 | I/O — User I/O pin (bank 4) |
| پن 92 | I/O — User I/O pin (bank 1) |
| پن 93 | I/O — User I/O pin (bank 1) |
| پن 94 | I/O — User I/O pin (bank 1) |
| پن 95 | DEV_OE — Device-wide output enable (optional) |
| پن 96 | DEV_CLRn — Device-wide clear (optional) |
| پن 97 | I/O — User I/O pin (bank 1) |
| پن 98 | I/O — User I/O pin (bank 1) |
| پن 99 | I/O — User I/O pin (bank 1) |
| پن 100 | I/O — User I/O pin (bank 1) |
عام استعمالات
EPM570GT100C3N کے لیے موزوں ہے 6 ایپلیکیشنs: Bus-Interface Bridging, I/O Expansion for Microcontrollers, Power-Sequencer / Reset Controller, Motor-Control State Machine, LED Display Driver / Multiplexer, Industrial Glue Logic.
Bus-Interface Bridging
The EPM570GT100C3N is well-suited for bus-interface bridging tasks such as PCI-to-local-bus, I2C-to-SPI muxing, and UART-to-parallel conversion. With 570 logic elements, 440 macrocells, and 5.4 ns pin-to-pin delay, the device can implement wide multiplexers and address/data demuxers in a single chip while maintaining deterministic timing across all 76 user I/O. Its MultiVolt I/O (1.5/1.8/2.5/3.3 V) lets it bridge a 3.3 V MCU to a 1.8 V ASIC directly. The instant-on Flash configuration eliminates the boot PROM typical of SRAM FPGAs, reducing BOM cost in bridges between legacy microcontrollers and modern SoCs in industrial control boards.
تجویز کردہ
I/O Expansion for Microcontrollers
When an MCU runs out of GPIO or peripheral channels, the EPM570GT100C3N provides 76 user I/O plus 8 Kbits of user Flash as a low-latency expansion port. The 5.4 ns tPD allows the CPLD to act as a high-speed coprocessor implementing PWM generators, quadrature decoders, or custom serial protocols without burdening the MCU. MultiVolt I/O means it can be wired directly to 1.8 V, 2.5 V, or 3.3 V MCUs without level shifters. Quartus II supports graphical state-machine entry, making it easy to add deterministic logic blocks alongside Cortex-M or PIC microcontrollers in motor-control and sensor-interface designs.
تجویز کردہ
Power-Sequencer / Reset Controller
The EPM570GT100C3N is widely used as a multi-rail power-sequencer and reset-distribution controller in ATCA, telecom, and server boards. With 5.4 ns deterministic delay, the device can implement programmable power-up/power-down sequencing across 6-12 voltage rails using its 440 macrocells, with feedback via GPIO and timers. The 1.8 V core draws minimal quiescent current and the flash-based configuration is instant-on, ensuring sequencing starts within microseconds of supply ramp. MultiVolt I/O can monitor 3.3 V enable signals and drive 1.8 V reset lines to ASICs from a single chip, replacing discrete supervisor ICs in cost-sensitive designs.
تجویز کردہ
Motor-Control State Machine
Industrial motor drives benefit from the EPM570GT100C3N's deterministic 5.4 ns timing and 76 I/O when implementing BLDC/PMSM commutation tables, Hall-sensor decoding, and PWM dead-time generation. The 440 macrocells are sufficient to hold a 6-step or FOC commutation lookup alongside multiple PWM channels, while MultiVolt I/O interfaces with 3.3 V MCUs and 1.8 V gate drivers. The 0C-85C commercial temperature range suits most industrial enclosures, and the MAX II G ('Green') variant offers low quiescent current important for battery-backed drives. Designers can simulate state machines in Quartus II and verify timing closure before silicon.
تجویز کردہ
LED Display Driver / Multiplexer
Large LED walls, scoreboards, and signage controllers leverage the EPM570GT100C3N's 76 user I/O to drive high-current row/column drivers and minimize MCU interrupt load. The 5.4 ns tPD supports scanning rates beyond 1 MHz, enabling 16+ row multiplex without flicker, while 440 macrocells handle gamma-correction lookup tables and refresh counters. MultiVolt I/O ties directly to 3.3 V shift registers or 5 V TTL buffers via external FETs. Flash-based instant-on eliminates the boot delay seen with FPGA-based LED controllers, allowing displays to be ready within 100 ms of power-up in retail and stadium installations.
تجویز کردہ
Industrial Glue Logic
Factory-automation backplanes and PLC I/O modules use the EPM570GT100C3N as classic glue logic: address decoding, chip-select generation, watchdog reset, and protocol translation between Modbus, CAN, and proprietary fieldbuses. The 100-pin TQFP is hand-solderable and rework-friendly, important for industrial customers with long lifecycles (10+ years). 8 Kbits of user Flash stores node IDs, calibration constants, and serial numbers, while MultiVolt I/O talks to legacy 5 V TTL peripherals via 3.3 V bank + 5 V tolerant input. Quartus II compatibility with VHDL/Verilog makes migration to MAX 10 trivial when a refresh is needed.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا EPM570GT100C3N — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | EPM570GT100C5N | EPM570GT100C4N | EPM570GT100I5N | EPM570F100C5N |
|---|---|---|---|---|---|
| Brand | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) | Altera (Intel) |
| Package | 100-pin TQFP (14x14 mm) | 100-pin TQFP (14x14 mm) | 100-pin TQFP (14x14 mm) | 100-pin TQFP (14x14 mm) | 100-pin TQFP (14x14 mm) |
| Logic Elements | 570 | 570 | 570 | 570 | 570 |
| Macrocells | 440 | 440 | 440 | 440 | 440 |
| User I/O | 76 | 76 | 76 | 76 | 76 |
| Core Voltage | 1.71-1.89 V (MAX II G) | 1.71-1.89 V (MAX II G) | 1.71-1.89 V (MAX II G) | 1.71-1.89 V (MAX II G) | 3.0-3.6 V (MAX II original) |
| Speed Grade (tPD max) | 3.0 ns (C3) | 5.4 ns (C5) | 4.0 ns (C4) | 5.4 ns (I5) | 5.4 ns (C5) |
| Operating Temperature | 0C to 85C (commercial) | 0C to 85C (commercial) | 0C to 85C (commercial) | -40C to 100C (industrial) | 0C to 85C (commercial) |
| User Flash | 8 Kbits | 8 Kbits | 8 Kbits | 8 Kbits | 8 Kbits |
اہم امتیازی خصوصیات
- Fastest speed grade in the MAX II G TQFP-100 family (بمقابلہEPM570GT100C5N)
- Industrial temperature range available in same package (بمقابلہEPM570GT100I5N)
- Lower core voltage reduces power vs original MAX II (بمقابلہEPM570F100C5N)
ڈیزائن نوٹس
The EPM570GT100C3N requires two distinct supplies: VCCINT (1.71-1.89 V, 1.8 V typical) for the core logic and VCCIOx (one per I/O bank, 1.5/1.8/2.5/3.3 V) for the I/O drivers. Decouple each VCC pin with a 0.1 uF ceramic capacitor placed within 100 mils of the pin, and add one bulk 10 uF tantalum or ceramic per supply rail. Power-on ramp must be monotonic; if the VCCINT rail glitches during programming the JTAG chain may corrupt the configuration Flash. Tie CONF_DONE and nSTATUS high via 10 kohm pull-ups because they are open-drain.
The 100-pin TQFP package has 0.5 mm lead pitch, which requires careful PCB layout: use 0.15 mm-wide solder paste apertures (5-mil stencil), guard traces between pads to prevent solder bridging, and provide a continuous ground plane beneath the device for thermal spreading and return-path integrity. Keep JTAG signals (TDI/TDO/TMS/TCK) short and isolated from switching I/O; add 10 kohm pull-ups on TMS and TCK as recommended by the MAX II handbook. Total package thermal resistance (theta_JA) for TQFP-100 is approximately 35 C/W on a 4-layer JEDEC test board - acceptable for the <300 mW typical dissipation of this part.
Do not confuse the EPM570GT100C3N (MAX II G, 1.8 V core) with the original EPM570T100C5N (MAX II, 3.3 V core) - they are pin-compatible but NOT drop-in substitutes because the VCCINT supply differs. Always check the second letter: 'G' = MAX II G (1.8 V core), 'F' or 'T' = original MAX II (3.3 V core). When migrating from MAX II to MAX II G, also verify the Quartus II device selection matches the silicon revision; an older bitstream will not load on the newer 'G' silicon. Estimated: typical IccINT at 50 MHz is approximately 30 mA for utilization below 50%.
Although CPLDs have slower edge rates than FPGAs, the EPM570GT100C3N can still drive 50 ohm controlled-impedance traces at 100 MHz if outputs are configured as 3-state with slew-rate limiting. For signals above 50 MHz, series-terminate the output with 33-ohm resistors placed within 200 mils of the CPLD pin to dampen reflections on the TQFP-100 lead frame. MultiVolt I/O banks allow mixing 3.3 V and 1.8 V buses on the same device, but unused I/O pins must be configured as outputs driving ground (not floating) to avoid supply-current transients during configuration.
تعمیل کی معلومات
RoHS compliant and lead-free per Altera/Intel product declaration. Not AEC-Q100 qualified - automotive customers should use the industrial-temperature I5N variant after their own qualification. Halogen-free status not explicitly confirmed in the available data.