Renesas Electronics

ISL8490IBZ - 5V 5Mbps RS-485 Transceiver | Renesas

MPN: ISL8490IBZ ✓ فعال
4.5 V to 5.5 V Vdss RS-485 and RS-422 Rds(on) 8-pin SOIC Package
MOQ: 1 |

ISL8490IBZ جائزہ

The Renesas Electronics ISL8490IBZ is a 5 V, full-duplex RS-485/RS-422 transceiver rated for data rates up to 5 Mbps and housed in an 8-pin SOIC package. It provides one balanced driver and one balanced receiver, supports a 4.5 V to 5.5 V supply range, and presents a single unit load to an RS-485 bus. The device is configured for full-duplex communication with separate transmit and receive paths.

An RS-485/RS-422 transceiver is an interface integrated circuit that converts between single-ended logic signals and differential balanced-line signals. Differential signaling improves noise immunity and allows reliable communication over longer cables or higher-noise industrial environments. The transceiver category belongs to interface ICs within the broader semiconductor hierarchy and is commonly used for multidrop industrial buses, point-to-point links, instrumentation, and building-control networks.

Key characteristics include a 5 Mbps maximum data rate, BiCMOS operation, full-duplex configuration, and operation from a 4.5 V to 5.5 V supply. The ISL8490IBZ is designed for systems that require separate differential transmit and receive lines. Its single-unit-load bus loading allows it to participate in conventional RS-485 networks while reducing the number of nodes permitted by a higher unit-load device.

The electrical architecture uses a differential driver for balanced bus outputs and a differential receiver for detecting small logic-level voltages. Receiver and driver-enable inputs support local control of bus direction and receiver state. Because the part provides separate transmit and receive paths, no multidrop half-duplex direction-control multiplexing is required, which simplifies full-duplex point-to-point and dual-bus designs.

Typical uses include industrial process-control links, factory automation equipment, test and measurement instruments, RS-422-compatible equipment, and isolated or non-isolated communication modules. The 5 Mbps capability is suitable for data links above the slower rates commonly associated with legacy RS-485 systems, while the 8-pin SOIC footprint supports compact board construction.

When laying out the circuit, route the differential pair as a tightly coupled pair with continuous ground reference, terminate the far end of each differential bus, and keep transceiver switching and protection circuitry away from sensitive receive nodes. Confirm that the selected termination, protection, isolation, and connector strategy preserves the signal integrity required at the intended data rate and cable length.

کے لیے ڈراپ اِن متبادل ISL8490IBZ — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

اس سیریز میں مختلف ورژن

اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں ISL8490IBZ (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Transceiver Configuration.

Renesas Electronics
Package: 8-SOIC (0.154 in, 3.90 mm width)
Transceiver Configuration: Single transceiver
موازنہ کریں ISL8490IBZ →

ISL8490IB

✅ ڈراپ-اِن
Renesas Electronics
📦 8-pin SOIC
5 V · RS-485 and RS-422 · Single transceiver · Low power · High speed or slew-rate limited · Differential balanced signaling · 8-SOIC (0.154 in, 3.90 mm width) · 8 pins

قیمت کے لیے رابطہ کریں

ڈیٹا شیٹ دیکھیں →

ISL8490IBZ تفصیلات

Product Type RS-485/RS-422 full-duplex transceiver
Transceiver Configuration 1 transmitter and 1 receiver
Supply Voltage Range 4.5 V to 5.5 V
Nominal Supply Voltage 5 V
Maximum Data Rate 5 Mbps
Communication Mode Full duplex
Supported Standards RS-485 and RS-422
RS-485 Bus Loading 1 unit load
Process Technology BiCMOS
آپریٹنگ درجہ حرارت رینج -40 °C to +85 °C
پیکیج 8-pin SOIC
Package Type 8-SOIC
ماؤنٹنگ ٹائپ Surface mount
Delivery Format Tube

ISL8490IBZ پن کنفیگریشن

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
پن 1 RO — Receiver output
پن 2 /RE — Active-low receiver enable
پن 3 DE — Driver enable
پن 4 DI — Driver data input
پن 5 GND — Ground
پن 6 Y — Non-inverting driver output
پن 7 Z — Inverting driver output
پن 8 VCC — Positive supply

عام استعمالات

ISL8490IBZ کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Process-Control Communications, Factory Automation Equipment, Test and Measurement Instrumentation, Building Control and Monitoring Networks, Point-to-Point RS-422 Data Links, Remote Sensor and Data-Acquisition Modules.

🏭

Industrial Process-Control Communications

The ISL8490IBZ fits full-duplex industrial links because it combines a 5 V supply range of 4.5 V to 5.5 V with operation up to 5 Mbps. Its separate differential transmitter and receiver allow command data to travel in one direction while acknowledgements or process measurements return simultaneously, avoiding shared-bus direction turnaround delays. The single-unit-load presentation is suitable for conventional RS-485 networks that limit node count. In a process-control instrument, the transceiver can connect a controller to a remote I/O module while providing continuous receive monitoring.

🏭

Factory Automation Equipment

The ISL8490IBZ supports factory automation modules that need reliable balanced communication in electrically noisy environments. Differential RS-485 signaling rejects much of the common-mode noise found near motors, relays, and switching power supplies, while the 5 Mbps capability supports faster data transfer than conventional low-rate RS-485 links. A controller can use separate transmit and receive pairs for continuous status exchange with a servo or programmable-logic module. PCB implementation should preserve a coupled differential route and use surge protection suitable for the installation environment.

🔧

Test and Measurement Instrumentation

The ISL8490IBZ is appropriate for instruments that exchange commands and measured data over a dedicated full-duplex RS-422 link. Its 5 Mbps maximum rate can shorten transfer time for configuration files, sample blocks, and diagnostic records, while the separate receive path permits continuous monitoring of remote equipment. The 8-pin SOIC package also suits compact instrument front ends. Designers should terminate the remote end of each differential pair, maintain a nearby supply bypass capacitor, and protect external cable-connected pins against transients.

🧩

Building Control and Monitoring Networks

The ISL8490IBZ can connect building controllers, sensors, and monitoring units over RS-485 or RS-422 wiring. Its 4.5 V to 5.5 V operating range accommodates regulated 5 V systems, and its single-unit-load interface supports standard bus loading. Full-duplex operation is especially useful between a central controller and a remote monitoring panel because control traffic and status data can proceed simultaneously. Maintain a continuous ground reference beneath the differential pair and use cable termination and protection appropriate for the building's routing and grounding practices.

🌐

Point-to-Point RS-422 Data Links

The ISL8490IBZ supports dedicated RS-422 point-to-point links by providing balanced differential output and input paths at rates up to 5 Mbps. This arrangement is useful when two devices must exchange information simultaneously without sharing a multidrop bus or implementing software-controlled bus turnaround. The device's full-duplex architecture simplifies firmware direction handling because transmit and receive channels remain physically separate. Board designers should pair each differential route with an appropriate ground reference, place termination at the far-end receiver, and keep connector and protection choices consistent with the cable environment.

📡

Remote Sensor and Data-Acquisition Modules

The ISL8490IBZ can interface a remote sensor or data-acquisition module to a local controller over a balanced bus. Its 5 Mbps capability provides ample link bandwidth for digitized measurements, while the receiver can remain active during transmission in a full-duplex arrangement. The single-unit-load characteristic supports networks designed around the electrical loading of the ISL8490 family. For field-connected equipment, add suitable transient protection, maintain controlled grounding, and verify that cable length and topology preserve usable signal margins at the operating data rate.

Where can I buy ISL8490IBZ online?
The ISL8490IBZ can be requested through XAIPART's Request a Quote form on this page. The form supports exact-part sourcing for the Renesas Electronics ISL8490IBZ in its 8-pin SOIC configuration. Confirm the required package form, quantity, shipment destination, and target date with the supplier before placing an order. Current commercial terms are best obtained directly through the quote workflow because availability and lead time can change.
What is the price of ISL8490IBZ?
Use XAIPART's Request a Quote form on this page for the current commercial price of the ISL8490IBZ. The quoted amount should correspond to the exact Renesas Electronics MPN, 8-pin SOIC package, order quantity, and delivery requirements. Because component pricing depends on quantity and market conditions, request a quantity-specific quote rather than relying on a general catalog figure. The form also provides a direct route for confirming stock and lead time.
What is the lead time for ISL8490IBZ?
The current lead time for ISL8490IBZ should be confirmed through XAIPART's Request a Quote form on this page. Lead time depends on the requested quantity, package form, factory inventory, and shipment destination. Request the quantity and delivery schedule when submitting the inquiry so the supplier can confirm the correct part and current material availability. This avoids relying on a generic availability statement that may not match the order.
Is ISL8490IBZ in stock?
Use the Request a Quote form on this page to check current availability for ISL8490IBZ. Include the required quantity, tube or other shipment format, and destination country. Availability can vary with order size and replenishment timing, so a stock confirmation should be requested for the exact production part rather than inferred from another ISL8490 family member. The same request can include a requested delivery date.
What are the key specifications of ISL8490IBZ?
The ISL8490IBZ is a 5 V, full-duplex RS-485/RS-422 transceiver with one transmitter, one receiver, and a maximum data rate of 5 Mbps. According to the Renesas ISL8485, ISL8490, and ISL8491 datasheet, the family operates from 4.5 V to 5.5 V, uses BiCMOS circuitry, and presents a single unit load to the RS-485 bus. The device is packaged in an 8-pin SOIC.
What is the operating voltage of ISL8490IBZ?
The ISL8490IBZ operates from 4.5 V to 5.5 V, allowing a 10% tolerance around a nominal 5 V supply. According to the Renesas ISL8485, ISL8490, and ISL8491 datasheet, this supply range applies to the BiCMOS transceiver family. The operating range should be checked against the supply voltage of the surrounding logic, while bypass capacitors should be placed close to the supply and ground pins.
How fast is the ISL8490IBZ RS-485 transceiver?
The ISL8490IBZ supports balanced communications at data rates up to 5 Mbps. The Renesas ISL8485, ISL8490, and ISL8491 datasheet identifies 5 Mbps as the maximum rate for this family. Achievable link performance also depends on cable length, transceiver enable timing, termination, protection components, connector geometry, and the integrity of the differential signal path.
What is the difference between ISL8490IBZ and ISL8491?
The ISL8490IBZ and ISL8491 belong to the same Renesas 5 V full-duplex RS-485/RS-422 family, but they are not established as pin-for-pin drop-in equivalents in the available manufacturer information. Both support balanced communication at rates up to 5 Mbps and use the 8-lead family construction. Verify driver-enable polarity, receiver-enable behavior, and the exact pin description table in the Renesas datasheet before replacing one device with the other.
When should I choose ISL8490IBZ over a half-duplex RS-485 transceiver?
Choose the ISL8490IBZ when the design requires simultaneous full-duplex operation with separate differential transmit and receive paths. Its dedicated receiver remains independent of the transmit direction, which simplifies point-to-point links and dual-bus equipment. A half-duplex transceiver may be preferable for a shared multidrop bus because it multiplexes driver and receiver functions, but that topology requires direction-control timing and a shared bus.
Is ISL8490IBZ suitable for industrial RS-485 equipment?
The ISL8490IBZ is suitable for industrial point-to-point and full-duplex equipment requiring a 5 V RS-485/RS-422 interface and data rates up to 5 Mbps. Its specified operating range of -40 °C to +85 °C supports temperature conditions commonly encountered in industrial electronics. The complete system must still address surge protection, grounding, isolation requirements, cable routing, and regulatory requirements for the target installation.
What is the best drop-in replacement for ISL8490IBZ?
The ISL8490IBZ-T is the Renesas ordering designation associated with the tape-and-reel form of the ISL8490IBZ, rather than a distinct drop-in electrical substitute. For another manufacturer's equivalent, verify the 8-pin SOIC footprint, full-duplex pin arrangement, 4.5 V to 5.5 V supply, 5 Mbps data rate, driver-enable polarity, receiver-enable behavior, and bus loading before approving a substitution. Request XAIPART's cross-reference assistance when those details are decisive.
Can an ISL8490IBZ replace an ISL8490IBZ-T?
The ISL8490IBZ and ISL8490IBZ-T are electrically associated Renesas designations whose principal distinction is the ordering or shipment format, with the latter appearing as the tape-and-reel designation in the product records. They should not be treated as distinct functional drop-in alternatives. Confirm the manufacturer's ordering table and the required assembly format, then confirm the exact MPN on the purchase order to avoid the wrong delivery format.
What can replace the ISL8490IBZ?
A suitable replacement for the ISL8490IBZ must match its 8-pin SOIC footprint, full-duplex RS-485/RS-422 architecture, 4.5 V to 5.5 V supply range, and 5 Mbps data-rate capability. The most direct Renesas ordering option is the ISL8490IBZ-T when tape-and-reel delivery is required. Cross-brand substitutions should be approved only after checking every pin, enable polarity, propagation delay, driver strength, receiver threshold, and bus unit load.
Is ISL8490IBZ the same as a Texas Instruments RS-485 transceiver?
The ISL8490IBZ is not automatically interchangeable with a Texas Instruments RS-485 transceiver despite the shared interface standard. A valid drop-in substitute must match the 8-pin SOIC footprint and all pin functions, including driver-enable polarity, receiver-enable polarity, receiver output behavior, supply range, and timing. Compare the candidate with the Renesas ISL8485, ISL8490, and ISL8491 datasheet and approve the substitution only after a board-level review.
Where can I download the ISL8490IBZ datasheet PDF and pinout?
The official Renesas document page for the ISL8485, ISL8490, and ISL8491 datasheet is the correct source for the ISL8490IBZ electrical specifications and pin descriptions. Open the Renesas ISL8490 part-details page for the device-specific ordering information. Use the datasheet's pin-description table when assigning the 8-pin SOIC connections, and use the package drawing to confirm lead orientation before routing the PCB.

کے لیے انجینئرنگ ریفرنس ڈیٹا ISL8490IBZ — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the ISL8490IBZ for a 5 V, full-duplex RS-485 or RS-422 interface that must operate at rates up to 5 Mbps. It is particularly appropriate when transmit and receive paths remain physically separate and shared-bus direction multiplexing is unnecessary. The ISL8490IB is a closely related same-family ordering option when its exact qualification, temperature, and order-code details satisfy the design; confirm those details with Renesas before substitution. The ISL8490IBZ-T is primarily an ordering and shipment-format designation rather than a distinct functional upgrade. For a cross-brand replacement, require the same 8-pin SOIC footprint, 4.5 V to 5.5 V supply range, full-duplex architecture, enable polarity, receiver behavior, bus loading, and 5 Mbps timing. In all cases, validate the complete interface against the cable, termination, protection, grounding, and EMC requirements of the final system.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ ISL8490IB
Brand Renesas Electronics Renesas Electronics
Package 8-pin SOIC 8-pin SOIC
Product Type RS-485/RS-422 transceiver RS-485/RS-422 transceiver
Transceiver Configuration 1 transmitter and 1 receiver 1 transmitter and 1 receiver
Supply Voltage Range 4.5 V to 5.5 V 4.5 V to 5.5 V
Maximum Data Rate 5 Mbps 5 Mbps
Communication Mode Full duplex Full duplex
RS-485 Bus Loading 1 unit load 1 unit load
Process Technology BiCMOS BiCMOS
Operating Temperature Range -40 °C to +85 °C -40 °C to +85 °C

اہم امتیازی خصوصیات

  • Dedicated full-duplex architecture (بمقابلہISL8490IB)
  • High-speed balanced communication (بمقابلہISL8490IB)
  • Single-unit-load RS-485 bus interface (بمقابلہISL8490IB)

ڈیزائن نوٹس

Route Y and Z as a tightly coupled differential pair with a continuous ground reference beneath or beside the pair. Keep the transceiver, connector, protection components, and receiver-side circuitry in a consistent signal path. Minimize stubs and avoid switching-node copper beneath the differential route. At 5 Mbps, trace geometry, return paths, and connector transitions can influence edge quality as much as the nominal transceiver bandwidth.

Do not treat the ISL8490IBZ as a shared-bus half-duplex device. It is configured for full duplex with separate differential transmit and receive paths, so the board must route both directions correctly. Apply termination at the physical far end of each receiver line rather than at every node. Also confirm driver-enable and receiver-enable polarity in the logic design before releasing the interface from reset.

Place the supply-decoupling capacitor immediately adjacent to VCC and the ground connection to minimize loop area. The family is specified for a 4.5 V to 5.5 V supply, so the source must remain within that range during startup and load transients. Use a quiet 5 V rail when transceiver noise could affect nearby sensitive circuitry, and verify the regulator's transient response because fast data edges can produce short current pulses.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The manufacturer product and datasheet records establish active status, device function, electrical characteristics, package, and ordering information. Specific environmental-material declarations were not established from the cited pages.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-15 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

ISL8490IBZ datasheet ISL8490IBZ pinout ISL8490IBZ datasheet pdf ISL8490IBZ equivalent ISL8490IBZ replacement ISL8490IBZ price Renesas ISL8490IBZ ISL8490IBZ 5Mbps RS-485 ISL8490IBZ 8-SOIC ISL8490IBZ RS-422 interface ISL8490IBZ vs ISL8490IB ISL8490IBZ full duplex transceiver

متعلقہ اجزاء اور اصطلاحات

Renesas Electronics ISL8490IBZ ISL8490IB ISL8490IBZ-T RS-485 RS-422 full-duplex transceiver half-duplex transceiver interface IC semiconductor BiCMOS differential signaling balanced line single unit load 5 Mbps data rate 4.5 V to 5.5 V supply 8-pin SOIC SOIC package family surface-mount package driver enable receiver enable industrial automation process control test and measurement
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں