ISL8490IBZ - 5V 5Mbps RS-485 Transceiver | Renesas
MPN: ISL8490IBZ ✓ 啟用中ISL8490IBZ 概覽
An RS-485/RS-422 transceiver is an interface integrated circuit that converts between single-ended logic signals and differential balanced-line signals. Differential signaling improves noise immunity and allows reliable communication over longer cables or higher-noise industrial environments. The transceiver category belongs to interface ICs within the broader semiconductor hierarchy and is commonly used for multidrop industrial buses, point-to-point links, instrumentation, and building-control networks.
Key characteristics include a 5 Mbps maximum data rate, BiCMOS operation, full-duplex configuration, and operation from a 4.5 V to 5.5 V supply. The ISL8490IBZ is designed for systems that require separate differential transmit and receive lines. Its single-unit-load bus loading allows it to participate in conventional RS-485 networks while reducing the number of nodes permitted by a higher unit-load device.
The electrical architecture uses a differential driver for balanced bus outputs and a differential receiver for detecting small logic-level voltages. Receiver and driver-enable inputs support local control of bus direction and receiver state. Because the part provides separate transmit and receive paths, no multidrop half-duplex direction-control multiplexing is required, which simplifies full-duplex point-to-point and dual-bus designs.
Typical uses include industrial process-control links, factory automation equipment, test and measurement instruments, RS-422-compatible equipment, and isolated or non-isolated communication modules. The 5 Mbps capability is suitable for data links above the slower rates commonly associated with legacy RS-485 systems, while the 8-pin SOIC footprint supports compact board construction.
When laying out the circuit, route the differential pair as a tightly coupled pair with continuous ground reference, terminate the far end of each differential bus, and keep transceiver switching and protection circuitry away from sensitive receive nodes. Confirm that the selected termination, protection, isolation, and connector strategy preserves the signal integrity required at the intended data rate and cable length.
直接替換替代品,適用於 ISL8490IBZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: ISL8490IBZ (相同外形與佔位) — 差異在於 Package, Transceiver Configuration.
ISL8490IBZ 規格
| Product Type | RS-485/RS-422 full-duplex transceiver |
| Transceiver Configuration | 1 transmitter and 1 receiver |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Nominal Supply Voltage | 5 V |
| Maximum Data Rate | 5 Mbps |
| Communication Mode | Full duplex |
| Supported Standards | RS-485 and RS-422 |
| RS-485 Bus Loading | 1 unit load |
| Process Technology | BiCMOS |
| 工作溫度範圍 | -40 °C to +85 °C |
| 封裝 | 8-pin SOIC |
| Package Type | 8-SOIC |
| 安裝類型 | Surface mount |
| Delivery Format | Tube |
ISL8490IBZ 腳位配置
| 腳位 1 | RO — Receiver output |
| 腳位 2 | /RE — Active-low receiver enable |
| 腳位 3 | DE — Driver enable |
| 腳位 4 | DI — Driver data input |
| 腳位 5 | GND — Ground |
| 腳位 6 | Y — Non-inverting driver output |
| 腳位 7 | Z — Inverting driver output |
| 腳位 8 | VCC — Positive supply |
典型應用
ISL8490IBZ 適用於 6 應用s: Industrial Process-Control Communications, Factory Automation Equipment, Test and Measurement Instrumentation, Building Control and Monitoring Networks, Point-to-Point RS-422 Data Links, Remote Sensor and Data-Acquisition Modules.
Industrial Process-Control Communications
The ISL8490IBZ fits full-duplex industrial links because it combines a 5 V supply range of 4.5 V to 5.5 V with operation up to 5 Mbps. Its separate differential transmitter and receiver allow command data to travel in one direction while acknowledgements or process measurements return simultaneously, avoiding shared-bus direction turnaround delays. The single-unit-load presentation is suitable for conventional RS-485 networks that limit node count. In a process-control instrument, the transceiver can connect a controller to a remote I/O module while providing continuous receive monitoring.
推薦
Factory Automation Equipment
The ISL8490IBZ supports factory automation modules that need reliable balanced communication in electrically noisy environments. Differential RS-485 signaling rejects much of the common-mode noise found near motors, relays, and switching power supplies, while the 5 Mbps capability supports faster data transfer than conventional low-rate RS-485 links. A controller can use separate transmit and receive pairs for continuous status exchange with a servo or programmable-logic module. PCB implementation should preserve a coupled differential route and use surge protection suitable for the installation environment.
推薦
Test and Measurement Instrumentation
The ISL8490IBZ is appropriate for instruments that exchange commands and measured data over a dedicated full-duplex RS-422 link. Its 5 Mbps maximum rate can shorten transfer time for configuration files, sample blocks, and diagnostic records, while the separate receive path permits continuous monitoring of remote equipment. The 8-pin SOIC package also suits compact instrument front ends. Designers should terminate the remote end of each differential pair, maintain a nearby supply bypass capacitor, and protect external cable-connected pins against transients.
推薦
Building Control and Monitoring Networks
The ISL8490IBZ can connect building controllers, sensors, and monitoring units over RS-485 or RS-422 wiring. Its 4.5 V to 5.5 V operating range accommodates regulated 5 V systems, and its single-unit-load interface supports standard bus loading. Full-duplex operation is especially useful between a central controller and a remote monitoring panel because control traffic and status data can proceed simultaneously. Maintain a continuous ground reference beneath the differential pair and use cable termination and protection appropriate for the building's routing and grounding practices.
推薦
Point-to-Point RS-422 Data Links
The ISL8490IBZ supports dedicated RS-422 point-to-point links by providing balanced differential output and input paths at rates up to 5 Mbps. This arrangement is useful when two devices must exchange information simultaneously without sharing a multidrop bus or implementing software-controlled bus turnaround. The device's full-duplex architecture simplifies firmware direction handling because transmit and receive channels remain physically separate. Board designers should pair each differential route with an appropriate ground reference, place termination at the far-end receiver, and keep connector and protection choices consistent with the cable environment.
推薦
Remote Sensor and Data-Acquisition Modules
The ISL8490IBZ can interface a remote sensor or data-acquisition module to a local controller over a balanced bus. Its 5 Mbps capability provides ample link bandwidth for digitized measurements, while the receiver can remain active during transmission in a full-duplex arrangement. The single-unit-load characteristic supports networks designed around the electrical loading of the ISL8490 family. For field-connected equipment, add suitable transient protection, maintain controlled grounding, and verify that cable length and topology preserve usable signal margins at the operating data rate.
推薦
推薦產品摘要
工程參考資料,適用於 ISL8490IBZ — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | ISL8490IB |
|---|---|---|
| Brand | Renesas Electronics | Renesas Electronics |
| Package | 8-pin SOIC | 8-pin SOIC |
| Product Type | RS-485/RS-422 transceiver | RS-485/RS-422 transceiver |
| Transceiver Configuration | 1 transmitter and 1 receiver | 1 transmitter and 1 receiver |
| Supply Voltage Range | 4.5 V to 5.5 V | 4.5 V to 5.5 V |
| Maximum Data Rate | 5 Mbps | 5 Mbps |
| Communication Mode | Full duplex | Full duplex |
| RS-485 Bus Loading | 1 unit load | 1 unit load |
| Process Technology | BiCMOS | BiCMOS |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C |
主要差異化特點
- Dedicated full-duplex architecture (對比ISL8490IB)
- High-speed balanced communication (對比ISL8490IB)
- Single-unit-load RS-485 bus interface (對比ISL8490IB)
設計說明
Route Y and Z as a tightly coupled differential pair with a continuous ground reference beneath or beside the pair. Keep the transceiver, connector, protection components, and receiver-side circuitry in a consistent signal path. Minimize stubs and avoid switching-node copper beneath the differential route. At 5 Mbps, trace geometry, return paths, and connector transitions can influence edge quality as much as the nominal transceiver bandwidth.
Do not treat the ISL8490IBZ as a shared-bus half-duplex device. It is configured for full duplex with separate differential transmit and receive paths, so the board must route both directions correctly. Apply termination at the physical far end of each receiver line rather than at every node. Also confirm driver-enable and receiver-enable polarity in the logic design before releasing the interface from reset.
Place the supply-decoupling capacitor immediately adjacent to VCC and the ground connection to minimize loop area. The family is specified for a 4.5 V to 5.5 V supply, so the source must remain within that range during startup and load transients. Use a quiet 5 V rail when transceiver noise could affect nearby sensitive circuitry, and verify the regulator's transient response because fast data edges can produce short current pulses.
合規資訊
The manufacturer product and datasheet records establish active status, device function, electrical characteristics, package, and ordering information. Specific environmental-material declarations were not established from the cited pages.