MAX232EIDWR - 250kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)
MPN: MAX232EIDWR ✓ فعالMAX232EIDWR جائزہ
A RS-232 transceiver is an interface IC that converts logic-level signals between TTL/CMOS equipment and balanced, bipolar RS-232 lines. Within the interface hierarchy, the MAX232E belongs to the line-driver/receiver family, implements the RS-232 physical-layer interface, and supports communication between equipment that uses different voltage domains. Its integrated charge-pump circuitry generates the required positive and negative voltage from one 5 V supply.
The device provides two transmit channels and two receive channels for full-duplex serial links. According to the Texas Instruments MAX232 datasheet, each receiver accepts inputs up to ±30 V, uses a typical threshold of 1.3 V, and has typical hysteresis of 0.5 V. The enhanced MAX232E variant supports 250 kbps operation and ±15 kV IEC-ESD protection, making it suitable for industrial control, instrumentation, and equipment interfaces exposed to electrostatic discharge.
Internally, the charge-pump voltage generator produces the bipolar voltages required by RS-232 drivers while onboard capacitors provide the required charge-pump operation. The MAX232EIDWR is specified for operation from −40 °C to +85 °C and uses the DW 16-pin SOIC package. Receiver inputs can withstand bipolar voltages up to ±30 V, while the drivers supply approximately ±9 V output levels for compliant RS-232 signaling.
Typical uses include industrial serial consoles, programmable test equipment, data-acquisition systems, point-of-sale terminals, and embedded controllers communicating with legacy RS-232 peripherals. The ±15 kV ESD rating is especially useful where a connector cable can expose the interface to electrostatic discharge, although system-level protection and grounding remain necessary for long or outdoor cables.
When laying out the circuit, place the charge-pump capacitors close to their associated pins and keep the RS-232 traces away from sensitive analog and high-speed digital paths. Provide a solid ground-plane connection and use appropriate cable transient protection when the interface leaves an enclosure. This page combines manufacturer specifications, replacement guidance, application engineering notes, and same-package comparisons for faster component selection and PCB planning.
کے لیے ڈراپ اِن متبادل MAX232EIDWR — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں MAX232EIDWR (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Maximum Data Rate, ESD Protection, Interface Standard, Package, Operating Temperature Range.
MAX232EESE+T
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX232ECWE-T
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MAX232IDW
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MAX232DWR
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MAX232EIDWR تفصیلات
| Product Type | Dual RS-232 driver/receiver |
| Number of Transmit Channels | 2 channels |
| Number of Receive Channels | 2 channels |
| Maximum Data Rate | 250 kbps |
| سپلائی وولٹیج | 5 V |
| Driver Output Level | ±9 V |
| Receiver Maximum Input Voltage | ±30 V |
| Receiver Typical Threshold | 1.3 V |
| Receiver Typical Hysteresis | 0.5 V |
| ESD Protection | ±15 kV IEC 61000-4-2 |
| آپریٹنگ درجہ حرارت رینج | −40 °C to +85 °C |
| پیکیج | 16-pin SOIC (DW) |
| پن کی تعداد | 16 pins |
| ماؤنٹنگ ٹائپ | Surface mount |
| Logic Levels | 5 V TTL/CMOS |
| Interface Standard | RS-232 |
| Charge-Pump Voltage Generation | Integrated, single 5 V supply |
MAX232EIDWR 16-pin soic (dw) پن کنفیگریشن گائیڈ
MAX232EIDWR (16-pin soic (dw) پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں MAX232EIDWR.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
MAX232EIDWR کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Serial Console Interface, Data Acquisition and Test Equipment, Programmable Controller Communication, Point-of-Sale Terminal Interface, Legacy Peripheral Connectivity, Instrumentation and Measurement Networks.
Industrial Serial Console Interface
The MAX232EIDWR fits industrial serial-console designs that require a 5 V logic-side interface and RS-232 levels on the cable side. Its dual transmitters and dual receivers support one full-duplex link, while the 250 kbps maximum rate provides more than enough bandwidth for terminal traffic. The −40 °C to +85 °C operating range supports equipment deployed in temperature-controlled industrial spaces. Its ±15 kV IEC 61000-4-2 protection rating improves interface survivability when the connector is accessible to personnel or maintenance equipment. The transmitter produces approximately ±9 V levels from the internal charge pump, so the system needs only one 5 V supply.
تجویز کردہ
Data Acquisition and Test Equipment
MAX232EIDWR is appropriate for data-acquisition instruments that exchange commands and measurement results with a host over RS-232. The 250 kbps maximum signaling rate supports moderate-rate telemetry while preserving compatibility with legacy equipment. Two receivers and two drivers allow one full-duplex port, and the 5 V operating supply simplifies integration with digital control circuitry. For bench instruments with exposed serial connectors, ±15 kV IEC 61000-4-2 protection adds useful electrostatic-discharge margin. Designers should still keep the interface ground connected to the chassis and evaluate additional surge protection for cables longer than a short bench lead.
تجویز کردہ
Programmable Controller Communication
The MAX232EIDWR can connect a 5 V embedded controller to an RS-232 host, service console, or configuration utility. The dual-driver, dual-receiver arrangement supports bidirectional command and data traffic without external level-shifting transistors. Its 250 kbps capability allows firmware to use a practical serial rate below the device maximum, while the integrated voltage generator avoids separate RS-232 power rails. For production equipment, the −40 °C to +85 °C rating provides useful environmental range. Because the MAX232EIDWR has no automatic direction control, the controller must manage transmitter enable state unless the selected connector wiring guarantees that only one transmitter is active.
تجویز کردہ
Point-of-Sale Terminal Interface
MAX232EIDWR is suitable for point-of-sale equipment that communicates with scanners, receipt printers, or service equipment over legacy RS-232. Its 5 V supply is convenient for systems already powered by a regulated 5 V rail, and the integrated charge pump provides approximately ±9 V driver outputs without a separate negative supply. The 250 kbps limit is substantially above the throughput of many point-of-sale peripherals. If the port is accessible through a service connector, the ±15 kV IEC 61000-4-2 rating improves robustness against electrostatic discharge. The final design should include a defined signal ground, short connector lead, and firmware that avoids enabling multiple transmitters simultaneously.
تجویز کردہ
Legacy Peripheral Connectivity
MAX232EIDWR provides a practical interface between modern 5 V digital electronics and legacy RS-232 peripherals such as older test equipment, industrial controllers, and service interfaces. The receiver translates bipolar line signals into 5 V TTL/CMOS levels, and the transmitter converts logic inputs into approximately ±9 V RS-232 outputs. Its receiver can accept bipolar inputs up to ±30 V, providing tolerance for off-state noise and standard RS-232 swings. The 250 kbps rate allows operation above the throughput of many legacy devices. Firmware should use framed packets and controlled transmitter states, while the PCB must provide the charge-pump capacitors and stable 5 V decoupling specified by the manufacturer.
تجویز کردہ
Instrumentation and Measurement Networks
MAX232EIDWR can bridge a 5 V measurement instrument to an RS-232 network of analyzers, source meters, or laboratory controllers. The 250 kbps maximum rate supports compact command-and-response protocols, while two receivers and two drivers provide flexible full-duplex channel use. The device operates across −40 °C to +85 °C, making it suitable for instrumentation intended for industrial environments as well as laboratories. Its ±15 kV IEC 61000-4-2 protection is useful when users repeatedly connect external cables, but it is not a substitute for correctly implemented cable grounding. Keep the interface ground and signal return together and isolate long external cable runs from sensitive measurement circuitry.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا MAX232EIDWR — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | MAX232EESE+T | MAX232ECWE-T | MAX232IDW | MAX232DWR |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOIC-16 (DW) | SOIC-16 (DW) | SOIC-16 (DW) | SOIC-16 (DW) | SOIC-16 (DW) |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps | 120 kbps | 120 kbps |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V |
| Driver Output Level | ±9 V | ±9 V | ±9 V | ±9 V | ±9 V |
| Transmit Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Receive Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Integrated Charge Pump | Yes | Yes | Yes | Yes | Yes |
اہم امتیازی خصوصیات
- Higher maximum signaling rate than the base MAX232 options (بمقابلہMAX232IDW)
- Enhanced ESD protection for accessible RS-232 connectors (بمقابلہMAX232DWR)
- Industrial temperature capability in the same 16-pin DW package (بمقابلہMAX232IDW)
- Higher data rate with the same approximately ±9 V driver output (بمقابلہMAX232ECWE-T)
ڈیزائن نوٹس
Follow the Texas Instruments MAX232 datasheet layout guidance for the charge-pump capacitors and place them close to the designated IC pins. Keep these high-current switching paths compact and connect the chip ground directly to the ground plane. Avoid routing the charge-pump node beneath sensitive analog or high-speed digital traces because the switched node can couple noise into adjacent circuits.
Do not assume that every MAX232 ordering suffix is an electrical and mechanical substitute. MAX232IDW is listed at 120 kbps, while MAX232EIDWR supports 250 kbps and ±15 kV IEC-ESD protection. Confirm the data rate, temperature grade, package width, exposed-pin arrangement, and pin functions before replacing a component on an existing PCB.
RS-232 can carry large transients when a cable is connected or disconnected. Connect the interface ground to the equipment chassis or ground structure at the connector entry, keep the cable return adjacent to the signal conductors, and avoid long unprotected stubs. The MAX232EIDWR's ±15 kV IEC 61000-4-2 rating should be treated as component-level protection rather than a complete cable-surge solution.
Decouple the 5 V supply locally and follow the manufacturer capacitor recommendations. The MAX232EIDWR includes a charge-pump generator, but its switched-capacitor operation draws periodic current from the supply. Use short, low-impedance power and ground paths, and verify that the source rail has adequate transient response for the installed board and cable interface.
تعمیل کی معلومات
The manufacturer identifies ±15 kV IEC 61000-4-2 ESD protection for the MAX232E family. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from current regional compliance documentation.