MAX232EIDWR - 250kbps RS-232 Transceiver | Texas Instruments (Tape & Reel)
料号: MAX232EIDWR ✓ 量产中MAX232EIDWR 概述
A RS-232 transceiver is an interface IC that converts logic-level signals between TTL/CMOS equipment and balanced, bipolar RS-232 lines. Within the interface hierarchy, the MAX232E belongs to the line-driver/receiver family, implements the RS-232 physical-layer interface, and supports communication between equipment that uses different voltage domains. Its integrated charge-pump circuitry generates the required positive and negative voltage from one 5 V supply.
The device provides two transmit channels and two receive channels for full-duplex serial links. According to the Texas Instruments MAX232 datasheet, each receiver accepts inputs up to ±30 V, uses a typical threshold of 1.3 V, and has typical hysteresis of 0.5 V. The enhanced MAX232E variant supports 250 kbps operation and ±15 kV IEC-ESD protection, making it suitable for industrial control, instrumentation, and equipment interfaces exposed to electrostatic discharge.
Internally, the charge-pump voltage generator produces the bipolar voltages required by RS-232 drivers while onboard capacitors provide the required charge-pump operation. The MAX232EIDWR is specified for operation from −40 °C to +85 °C and uses the DW 16-pin SOIC package. Receiver inputs can withstand bipolar voltages up to ±30 V, while the drivers supply approximately ±9 V output levels for compliant RS-232 signaling.
Typical uses include industrial serial consoles, programmable test equipment, data-acquisition systems, point-of-sale terminals, and embedded controllers communicating with legacy RS-232 peripherals. The ±15 kV ESD rating is especially useful where a connector cable can expose the interface to electrostatic discharge, although system-level protection and grounding remain necessary for long or outdoor cables.
When laying out the circuit, place the charge-pump capacitors close to their associated pins and keep the RS-232 traces away from sensitive analog and high-speed digital paths. Provide a solid ground-plane connection and use appropriate cable transient protection when the interface leaves an enclosure. This page combines manufacturer specifications, replacement guidance, application engineering notes, and same-package comparisons for faster component selection and PCB planning.
直接替换替代料: MAX232EIDWR ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: MAX232EIDWR (相同外形与封装尺寸) ——差异在于 Maximum Data Rate, ESD Protection, Interface Standard, Package, Operating Temperature Range.
MAX232EESE+T
✅ 直接替换📋 参考替代料(不在目录中)
MAX232ECWE-T
✅ 直接替换📋 参考替代料(不在目录中)
MAX232EIDWR 规格参数
| Product Type | Dual RS-232 driver/receiver |
| Number of Transmit Channels | 2 channels |
| Number of Receive Channels | 2 channels |
| Maximum Data Rate | 250 kbps |
| 电源电压 | 5 V |
| Driver Output Level | ±9 V |
| Receiver Maximum Input Voltage | ±30 V |
| Receiver Typical Threshold | 1.3 V |
| Receiver Typical Hysteresis | 0.5 V |
| ESD Protection | ±15 kV IEC 61000-4-2 |
| 工作温度范围 | −40 °C to +85 °C |
| 封装 | 16-pin SOIC (DW) |
| 引脚数量 | 16 pins |
| 安装类型 | Surface mount |
| Logic Levels | 5 V TTL/CMOS |
| Interface Standard | RS-232 |
| Charge-Pump Voltage Generation | Integrated, single 5 V supply |
MAX232EIDWR 16-pin soic (dw) 引脚配置指南
MAX232EIDWR(16-pin soic (dw) 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: MAX232EIDWR.
请参阅 数据手册 以查看完整引脚配置。
典型应用
MAX232EIDWR 适用于 6 应用s: Industrial Serial Console Interface, Data Acquisition and Test Equipment, Programmable Controller Communication, Point-of-Sale Terminal Interface, Legacy Peripheral Connectivity, Instrumentation and Measurement Networks.
Industrial Serial Console Interface
The MAX232EIDWR fits industrial serial-console designs that require a 5 V logic-side interface and RS-232 levels on the cable side. Its dual transmitters and dual receivers support one full-duplex link, while the 250 kbps maximum rate provides more than enough bandwidth for terminal traffic. The −40 °C to +85 °C operating range supports equipment deployed in temperature-controlled industrial spaces. Its ±15 kV IEC 61000-4-2 protection rating improves interface survivability when the connector is accessible to personnel or maintenance equipment. The transmitter produces approximately ±9 V levels from the internal charge pump, so the system needs only one 5 V supply.
推荐
Data Acquisition and Test Equipment
MAX232EIDWR is appropriate for data-acquisition instruments that exchange commands and measurement results with a host over RS-232. The 250 kbps maximum signaling rate supports moderate-rate telemetry while preserving compatibility with legacy equipment. Two receivers and two drivers allow one full-duplex port, and the 5 V operating supply simplifies integration with digital control circuitry. For bench instruments with exposed serial connectors, ±15 kV IEC 61000-4-2 protection adds useful electrostatic-discharge margin. Designers should still keep the interface ground connected to the chassis and evaluate additional surge protection for cables longer than a short bench lead.
推荐
Programmable Controller Communication
The MAX232EIDWR can connect a 5 V embedded controller to an RS-232 host, service console, or configuration utility. The dual-driver, dual-receiver arrangement supports bidirectional command and data traffic without external level-shifting transistors. Its 250 kbps capability allows firmware to use a practical serial rate below the device maximum, while the integrated voltage generator avoids separate RS-232 power rails. For production equipment, the −40 °C to +85 °C rating provides useful environmental range. Because the MAX232EIDWR has no automatic direction control, the controller must manage transmitter enable state unless the selected connector wiring guarantees that only one transmitter is active.
推荐
Point-of-Sale Terminal Interface
MAX232EIDWR is suitable for point-of-sale equipment that communicates with scanners, receipt printers, or service equipment over legacy RS-232. Its 5 V supply is convenient for systems already powered by a regulated 5 V rail, and the integrated charge pump provides approximately ±9 V driver outputs without a separate negative supply. The 250 kbps limit is substantially above the throughput of many point-of-sale peripherals. If the port is accessible through a service connector, the ±15 kV IEC 61000-4-2 rating improves robustness against electrostatic discharge. The final design should include a defined signal ground, short connector lead, and firmware that avoids enabling multiple transmitters simultaneously.
推荐
Legacy Peripheral Connectivity
MAX232EIDWR provides a practical interface between modern 5 V digital electronics and legacy RS-232 peripherals such as older test equipment, industrial controllers, and service interfaces. The receiver translates bipolar line signals into 5 V TTL/CMOS levels, and the transmitter converts logic inputs into approximately ±9 V RS-232 outputs. Its receiver can accept bipolar inputs up to ±30 V, providing tolerance for off-state noise and standard RS-232 swings. The 250 kbps rate allows operation above the throughput of many legacy devices. Firmware should use framed packets and controlled transmitter states, while the PCB must provide the charge-pump capacitors and stable 5 V decoupling specified by the manufacturer.
推荐
Instrumentation and Measurement Networks
MAX232EIDWR can bridge a 5 V measurement instrument to an RS-232 network of analyzers, source meters, or laboratory controllers. The 250 kbps maximum rate supports compact command-and-response protocols, while two receivers and two drivers provide flexible full-duplex channel use. The device operates across −40 °C to +85 °C, making it suitable for instrumentation intended for industrial environments as well as laboratories. Its ±15 kV IEC 61000-4-2 protection is useful when users repeatedly connect external cables, but it is not a substitute for correctly implemented cable grounding. Keep the interface ground and signal return together and isolate long external cable runs from sensitive measurement circuitry.
推荐
推荐产品汇总
工程参考数据: MAX232EIDWR ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | MAX232EESE+T | MAX232ECWE-T | MAX232IDW | MAX232DWR |
|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | SOIC-16 (DW) | SOIC-16 (DW) | SOIC-16 (DW) | SOIC-16 (DW) | SOIC-16 (DW) |
| Maximum Data Rate | 250 kbps | 250 kbps | 250 kbps | 120 kbps | 120 kbps |
| Supply Voltage | 5 V | 5 V | 5 V | 5 V | 5 V |
| Driver Output Level | ±9 V | ±9 V | ±9 V | ±9 V | ±9 V |
| Transmit Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Receive Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Integrated Charge Pump | Yes | Yes | Yes | Yes | Yes |
关键差异点
- Higher maximum signaling rate than the base MAX232 options (对比 MAX232IDW)
- Enhanced ESD protection for accessible RS-232 connectors (对比 MAX232DWR)
- Industrial temperature capability in the same 16-pin DW package (对比 MAX232IDW)
- Higher data rate with the same approximately ±9 V driver output (对比 MAX232ECWE-T)
设计说明
Follow the Texas Instruments MAX232 datasheet layout guidance for the charge-pump capacitors and place them close to the designated IC pins. Keep these high-current switching paths compact and connect the chip ground directly to the ground plane. Avoid routing the charge-pump node beneath sensitive analog or high-speed digital traces because the switched node can couple noise into adjacent circuits.
Do not assume that every MAX232 ordering suffix is an electrical and mechanical substitute. MAX232IDW is listed at 120 kbps, while MAX232EIDWR supports 250 kbps and ±15 kV IEC-ESD protection. Confirm the data rate, temperature grade, package width, exposed-pin arrangement, and pin functions before replacing a component on an existing PCB.
RS-232 can carry large transients when a cable is connected or disconnected. Connect the interface ground to the equipment chassis or ground structure at the connector entry, keep the cable return adjacent to the signal conductors, and avoid long unprotected stubs. The MAX232EIDWR's ±15 kV IEC 61000-4-2 rating should be treated as component-level protection rather than a complete cable-surge solution.
Decouple the 5 V supply locally and follow the manufacturer capacitor recommendations. The MAX232EIDWR includes a charge-pump generator, but its switched-capacitor operation draws periodic current from the supply. Use short, low-impedance power and ground paths, and verify that the source rail has adequate transient response for the installed board and cable interface.
合规信息
The manufacturer identifies ±15 kV IEC 61000-4-2 ESD protection for the MAX232E family. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from current regional compliance documentation.