OPA350UA - 38MHz High-Speed Rail-to-Rail Op Amp | TI
MPN: OPA350UA ✓ فعالOPA350UA جائزہ
An operational amplifier is an analog integrated circuit that provides high open-loop gain while processing a differential input signal. The OPA350 family adds rail-to-rail input and output capability, allowing signals to operate close to the supply rails. This rail-to-rail behavior makes it useful in battery-powered equipment, low-voltage sensor interfaces, audio paths, communication equipment, and control systems where conventional non-rail-to-rail amplifiers would clip or restrict headroom.
Key features include 5 nV/√Hz noise density, 38 MHz gain-bandwidth product, and 22 V/µs slew rate. The amplifier operates from a 2.7 V to 5.5 V single supply, and its input common-mode range extends approximately 300 mV below ground and 300 mV above the positive supply. The CMOS implementation also supports low-voltage operation while preserving high-speed transient performance needed for ADC drive and active filtering.
OPA350 series devices are optimized for driving sampling analog-to-digital converters, cell-phone power-amplifier control loops, and video-processing systems. The manufacturer identifies 75-ohm video-drive capability as an application area. Its combination of low noise, wide bandwidth, and rail-to-rail swing supports signal chains where both small-signal fidelity and large-signal linearity are important.
Typical uses include low-voltage ADC input stages, precision current sensing, audio preamplification, active filters, and high-speed control loops. The 38 MHz bandwidth provides useful margin when filtering higher-frequency signals, while the low 5 nV/√Hz noise density helps preserve weak-signal integrity. Slew rate must be checked against the amplitude and bandwidth requirements of the largest intended output waveform.
For layout, place input, feedback, and decoupling components close to their associated pins, and use a short, low-inductance ground return. Maintain a stable feedback network and avoid routing high-impedance input traces beside digital or switching-current paths. The low-voltage operating range does not eliminate the need for supply filtering, particularly when the amplifier is used immediately before a sampling ADC.
This page combines manufacturer specifications, package and pin information, practical application guidance, and structured comparisons with pin-compatible operational-amplifier alternatives to support faster component selection and board-level implementation.
کے لیے ڈراپ اِن متبادل OPA350UA — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں OPA350UA (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Gain-Bandwidth Product, Package, Slew Rate, Input Common-Mode Range, Supply Voltage Range.
OPA351UA
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
OPA353UA
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →OPA300UA
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
OPA310UA
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
ADA4661ARZ
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
OPA350UA زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Amplifier Type | Single operational amplifier |
| ٹوپولوجی | Rail-to-rail input and output CMOS |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 38 MHz |
| Slew Rate | 22 V/µs |
| Input Noise Density | 5 nV/√Hz |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Supply Type | Single supply |
| Input Common-Mode Range | Approximately 300 mV below ground to 300 mV above positive supply |
| Output Swing | Rail-to-rail |
| Input Type | Rail-to-rail |
| پیکیج | 8-pin SOIC |
| ماؤنٹنگ ٹائپ | Surface mount |
OPA350UA 8-pin soic پن کنفیگریشن گائیڈ
OPA350UA (8-pin soic پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں OPA350UA.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
OPA350UA کے لیے موزوں ہے 6 ایپلیکیشنs: Sampling ADC Input Driver, Low-Noise Audio Preamplifier, Cell-Phone Power Amplifier Control Loop, Precision Current Sensing, Video Signal Conditioning, Active Analog Filter.
Sampling ADC Input Driver
The OPA350UA fits low-voltage ADC front ends because its 38 MHz gain-bandwidth product and 22 V/µs slew rate preserve signal amplitude and edge performance beyond the converter’s useful bandwidth. The 5 nV/√Hz input-noise density is also favorable for weak signals where analog gain is limited. Place the amplifier close to the ADC input and keep the feedback network compact to reduce parasitic capacitance and improve settling. The 2.7 V to 5.5 V operating range supports 3.3 V and 5 V converter rails, while rail-to-rail input and output behavior reduces signal-headroom constraints. Check the converter’s settling requirements, input capacitance, and required gain before finalizing the filter and feedback values.
تجویز کردہ
Low-Noise Audio Preamplifier
The OPA350UA is suitable for low-noise audio preamplification because its 5 nV/√Hz input-noise density reduces the amplifier’s contribution to weak-signal noise, while its 38 MHz bandwidth provides ample margin for audio control and filtering stages. Rail-to-rail input and output operation supports signals that approach the supply limits, and the 22 V/µs slew rate improves handling of larger transient waveforms. Use stable feedback ratios appropriate for the required gain and frequency response. Resistor thermal noise and input-bias-current error can dominate at high source impedances, so the complete signal path should be evaluated rather than relying on the 5 nV/√Hz figure alone.
تجویز کردہ
Cell-Phone Power Amplifier Control Loop
OPA350UA is identified by Texas Instruments for cell-phone power-amplifier control loops, where a high-speed amplifier can respond quickly to envelope or feedback-control signals. Its 38 MHz gain-bandwidth product and 22 V/µs slew rate help minimize delay in the control path, while the 5 nV/√Hz noise density can preserve small feedback signals. The single-supply operation from 2.7 V to 5.5 V aligns with compact portable-system rails. Keep the control trace short, provide local supply bypassing, and verify phase margin and loop stability with the actual compensation network before deployment.
تجویز کردہ
Precision Current Sensing
OPA350UA can amplify the small differential voltage generated by a low-value shunt resistor in low-voltage current-measurement systems. Its low 5 nV/√Hz input-noise density limits the amplifier’s voltage-noise contribution, while rail-to-rail input and output operation helps use the available measurement range in a 2.7 V to 5.5 V system. The 38 MHz bandwidth allows the amplifier to respond to relatively fast current transients. Use a Kelvin connection from the shunt to reduce parasitic voltage pickup, and verify offset, bias-current error, common-mode limits, and shunt heating against the required measurement accuracy.
تجویز کردہ
Video Signal Conditioning
OPA350UA is suitable for video-processing signal conditioning because its 38 MHz bandwidth, 22 V/µs slew rate, and rail-to-rail output support 75-ohm video-drive applications identified by the manufacturer. The amplifier can condition a video waveform before routing it to another stage, with sufficient bandwidth for common baseband video signals and higher-frequency transitions. Preserve the source and termination geometry, keep the feedback loop compact, and maintain a continuous return path to reduce ringing. If the circuit processes standard-definition, high-definition, or composite video, check the required gain, output amplitude, settling time, and channel-to-channel matching before production release.
تجویز کردہ
Active Analog Filter
OPA350UA can implement active filters in low-voltage instrumentation because its 38 MHz gain-bandwidth product provides useful loop gain above the filter corner frequency, and the 22 V/µs slew rate supports signal transitions with reduced distortion. The 5 nV/√Hz noise density is valuable when filtering small analog signals, while the single 2.7 V to 5.5 V supply simplifies portable-system power design. Select feedback resistors and capacitors for the required transfer function, then verify phase margin and gain peaking with the amplifier’s exact gain-noise curve. Place filter components close to the package and provide local bypassing to reduce instability caused by long feedback traces.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا OPA350UA — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | OPA351UA | OPA353UA | OPA300UA | OPA310UA | ADA4661ARZ |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Amplifier Type | Single CMOS operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier |
| Gain-Bandwidth Product | 38 MHz | 38 MHz | 44 MHz | 50 MHz | 35 MHz | 18 MHz |
| Primary Application | ADC drive, control loops, and video processing | Low-voltage high-speed signal conditioning | High-speed single-supply signal conditioning | Low-power high-speed signal conditioning | Low-noise high-speed signal conditioning | Precision low-voltage signal conditioning |
اہم امتیازی خصوصیات
- Balanced low-noise and high-speed performance (بمقابلہOPA351UA)
- More bandwidth for faster edge response (بمقابلہOPA353UA)
- Lower-power design option in the same pin-compatible family (بمقابلہOPA300UA)
ڈیزائن نوٹس
Place input, feedback, and bypass components directly adjacent to the OPA350UA pins. Keep the noninverting input and inverting input routes short, particularly for high-gain or high-frequency configurations. Connect the decoupling capacitor to a low-impedance ground plane, and avoid routing the input node alongside regulators, clock lines, or switching-node traces. Parasitic capacitance introduced by long PCB traces can reduce phase margin and alter the effective feedback factor.
Use the 38 MHz gain-bandwidth product and 22 V/µs slew rate as design limits, not guarantees of usable closed-loop bandwidth. The maximum practical bandwidth depends on noise gain, feedback impedance, capacitive loading, and loop stability. When driving an ADC or cable, evaluate settling behavior with the actual load and consider a small isolation resistor near the amplifier output if capacitive loading could cause peaking.
The OPA350UA is intended for a single supply from 2.7 V to 5.5 V. Provide local high-frequency decoupling close to the supply pins and ensure the source can support output-current peaks without disturbing the amplifier's signal headroom. Rail-to-rail behavior reduces output-swing restrictions, but it does not eliminate supply noise, and the 5 nV/√Hz input-noise specification cannot compensate for noisy supply rails or poorly connected shunt resistors.
Do not assume that every 8-pin SOIC high-speed amplifier is interchangeable with the OPA350UA. Confirm pin orientation, supply pins, input and output assignments, common-mode limits, output swing, stability, and offset behavior from the exact replacement data sheet. For ADC applications, also verify output settling and capacitive-load drive. A footprint match alone is insufficient to guarantee equivalent signal performance.
تعمیل کی معلومات
Exact RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for OPA350UA were not identified. Obtain current manufacturer documentation before making a compliance claim.