OPA350UA - 38MHz High-Speed Rail-to-Rail Op Amp | TI
N.º de pieza: OPA350UA ✓ ActivoOPA350UA Descripción general
An operational amplifier is an analog integrated circuit that provides high open-loop gain while processing a differential input signal. The OPA350 family adds rail-to-rail input and output capability, allowing signals to operate close to the supply rails. This rail-to-rail behavior makes it useful in battery-powered equipment, low-voltage sensor interfaces, audio paths, communication equipment, and control systems where conventional non-rail-to-rail amplifiers would clip or restrict headroom.
Key features include 5 nV/√Hz noise density, 38 MHz gain-bandwidth product, and 22 V/µs slew rate. The amplifier operates from a 2.7 V to 5.5 V single supply, and its input common-mode range extends approximately 300 mV below ground and 300 mV above the positive supply. The CMOS implementation also supports low-voltage operation while preserving high-speed transient performance needed for ADC drive and active filtering.
OPA350 series devices are optimized for driving sampling analog-to-digital converters, cell-phone power-amplifier control loops, and video-processing systems. The manufacturer identifies 75-ohm video-drive capability as an application area. Its combination of low noise, wide bandwidth, and rail-to-rail swing supports signal chains where both small-signal fidelity and large-signal linearity are important.
Typical uses include low-voltage ADC input stages, precision current sensing, audio preamplification, active filters, and high-speed control loops. The 38 MHz bandwidth provides useful margin when filtering higher-frequency signals, while the low 5 nV/√Hz noise density helps preserve weak-signal integrity. Slew rate must be checked against the amplitude and bandwidth requirements of the largest intended output waveform.
For layout, place input, feedback, and decoupling components close to their associated pins, and use a short, low-inductance ground return. Maintain a stable feedback network and avoid routing high-impedance input traces beside digital or switching-current paths. The low-voltage operating range does not eliminate the need for supply filtering, particularly when the amplifier is used immediately before a sampling ADC.
This page combines manufacturer specifications, package and pin information, practical application guidance, and structured comparisons with pin-compatible operational-amplifier alternatives to support faster component selection and board-level implementation.
Alternativas directas para OPA350UA — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con OPA350UA (mismo factor de forma y huella) — difiere en Gain-Bandwidth Product, Package, Slew Rate, Input Common-Mode Range, Supply Voltage Range.
OPA351UA
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
OPA353UA
✅ Sustitución directaConsulte el precio
Ver hoja de datos →OPA300UA
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
OPA310UA
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
ADA4661ARZ
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
OPA350UA Valores máximos y características eléctricas
| Amplifier Type | Single operational amplifier |
| Topología | Rail-to-rail input and output CMOS |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 38 MHz |
| Slew Rate | 22 V/µs |
| Input Noise Density | 5 nV/√Hz |
| Supply Voltage Range | 2.7 V to 5.5 V |
| Supply Type | Single supply |
| Input Common-Mode Range | Approximately 300 mV below ground to 300 mV above positive supply |
| Output Swing | Rail-to-rail |
| Input Type | Rail-to-rail |
| Encapsulado | 8-pin SOIC |
| Tipo de montaje | Surface mount |
Guía de configuración de pines de OPA350UA 8-pin soic
Configuración de pines para OPA350UA (encapsulado 8-pin soic). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para OPA350UA.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
OPA350UA es adecuado para 6 aplicacións: Sampling ADC Input Driver, Low-Noise Audio Preamplifier, Cell-Phone Power Amplifier Control Loop, Precision Current Sensing, Video Signal Conditioning, Active Analog Filter.
Sampling ADC Input Driver
The OPA350UA fits low-voltage ADC front ends because its 38 MHz gain-bandwidth product and 22 V/µs slew rate preserve signal amplitude and edge performance beyond the converter’s useful bandwidth. The 5 nV/√Hz input-noise density is also favorable for weak signals where analog gain is limited. Place the amplifier close to the ADC input and keep the feedback network compact to reduce parasitic capacitance and improve settling. The 2.7 V to 5.5 V operating range supports 3.3 V and 5 V converter rails, while rail-to-rail input and output behavior reduces signal-headroom constraints. Check the converter’s settling requirements, input capacitance, and required gain before finalizing the filter and feedback values.
Recomendado
Low-Noise Audio Preamplifier
The OPA350UA is suitable for low-noise audio preamplification because its 5 nV/√Hz input-noise density reduces the amplifier’s contribution to weak-signal noise, while its 38 MHz bandwidth provides ample margin for audio control and filtering stages. Rail-to-rail input and output operation supports signals that approach the supply limits, and the 22 V/µs slew rate improves handling of larger transient waveforms. Use stable feedback ratios appropriate for the required gain and frequency response. Resistor thermal noise and input-bias-current error can dominate at high source impedances, so the complete signal path should be evaluated rather than relying on the 5 nV/√Hz figure alone.
Recomendado
Cell-Phone Power Amplifier Control Loop
OPA350UA is identified by Texas Instruments for cell-phone power-amplifier control loops, where a high-speed amplifier can respond quickly to envelope or feedback-control signals. Its 38 MHz gain-bandwidth product and 22 V/µs slew rate help minimize delay in the control path, while the 5 nV/√Hz noise density can preserve small feedback signals. The single-supply operation from 2.7 V to 5.5 V aligns with compact portable-system rails. Keep the control trace short, provide local supply bypassing, and verify phase margin and loop stability with the actual compensation network before deployment.
Recomendado
Precision Current Sensing
OPA350UA can amplify the small differential voltage generated by a low-value shunt resistor in low-voltage current-measurement systems. Its low 5 nV/√Hz input-noise density limits the amplifier’s voltage-noise contribution, while rail-to-rail input and output operation helps use the available measurement range in a 2.7 V to 5.5 V system. The 38 MHz bandwidth allows the amplifier to respond to relatively fast current transients. Use a Kelvin connection from the shunt to reduce parasitic voltage pickup, and verify offset, bias-current error, common-mode limits, and shunt heating against the required measurement accuracy.
Recomendado
Video Signal Conditioning
OPA350UA is suitable for video-processing signal conditioning because its 38 MHz bandwidth, 22 V/µs slew rate, and rail-to-rail output support 75-ohm video-drive applications identified by the manufacturer. The amplifier can condition a video waveform before routing it to another stage, with sufficient bandwidth for common baseband video signals and higher-frequency transitions. Preserve the source and termination geometry, keep the feedback loop compact, and maintain a continuous return path to reduce ringing. If the circuit processes standard-definition, high-definition, or composite video, check the required gain, output amplitude, settling time, and channel-to-channel matching before production release.
Recomendado
Active Analog Filter
OPA350UA can implement active filters in low-voltage instrumentation because its 38 MHz gain-bandwidth product provides useful loop gain above the filter corner frequency, and the 22 V/µs slew rate supports signal transitions with reduced distortion. The 5 nV/√Hz noise density is valuable when filtering small analog signals, while the single 2.7 V to 5.5 V supply simplifies portable-system power design. Select feedback resistors and capacitors for the required transfer function, then verify phase margin and gain peaking with the amplifier’s exact gain-noise curve. Place filter components close to the package and provide local bypassing to reduce instability caused by long feedback traces.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para OPA350UA — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | OPA351UA | OPA353UA | OPA300UA | OPA310UA | ADA4661ARZ |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Analog Devices |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Amplifier Type | Single CMOS operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier |
| Gain-Bandwidth Product | 38 MHz | 38 MHz | 44 MHz | 50 MHz | 35 MHz | 18 MHz |
| Primary Application | ADC drive, control loops, and video processing | Low-voltage high-speed signal conditioning | High-speed single-supply signal conditioning | Low-power high-speed signal conditioning | Low-noise high-speed signal conditioning | Precision low-voltage signal conditioning |
Diferenciadores clave
- Balanced low-noise and high-speed performance (frente a OPA351UA)
- More bandwidth for faster edge response (frente a OPA353UA)
- Lower-power design option in the same pin-compatible family (frente a OPA300UA)
Notas de diseño
Place input, feedback, and bypass components directly adjacent to the OPA350UA pins. Keep the noninverting input and inverting input routes short, particularly for high-gain or high-frequency configurations. Connect the decoupling capacitor to a low-impedance ground plane, and avoid routing the input node alongside regulators, clock lines, or switching-node traces. Parasitic capacitance introduced by long PCB traces can reduce phase margin and alter the effective feedback factor.
Use the 38 MHz gain-bandwidth product and 22 V/µs slew rate as design limits, not guarantees of usable closed-loop bandwidth. The maximum practical bandwidth depends on noise gain, feedback impedance, capacitive loading, and loop stability. When driving an ADC or cable, evaluate settling behavior with the actual load and consider a small isolation resistor near the amplifier output if capacitive loading could cause peaking.
The OPA350UA is intended for a single supply from 2.7 V to 5.5 V. Provide local high-frequency decoupling close to the supply pins and ensure the source can support output-current peaks without disturbing the amplifier's signal headroom. Rail-to-rail behavior reduces output-swing restrictions, but it does not eliminate supply noise, and the 5 nV/√Hz input-noise specification cannot compensate for noisy supply rails or poorly connected shunt resistors.
Do not assume that every 8-pin SOIC high-speed amplifier is interchangeable with the OPA350UA. Confirm pin orientation, supply pins, input and output assignments, common-mode limits, output swing, stability, and offset behavior from the exact replacement data sheet. For ADC applications, also verify output settling and capacitive-load drive. A footprint match alone is insufficient to guarantee equivalent signal performance.
Información de cumplimiento
Exact RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for OPA350UA were not identified. Obtain current manufacturer documentation before making a compliance claim.