Texas Instruments

OPA350UA - 38MHz High-Speed Rail-to-Rail Op Amp | TI

MPN: OPA350UA ✓ Hoạt động
2.7 V to 5.5 V Vdss 8-pin SOIC Package
MOQ: 1 |

OPA350UA Tóm tắt

Texas Instruments OPA350UA is a single, rail-to-rail CMOS operational amplifier optimized for low-voltage, single-supply operation. It provides a 38 MHz gain-bandwidth product, 22 V/µs slew rate, and 5 nV/√Hz input-noise density in an 8-pin SOIC package. These characteristics place the OPA350UA in the operational-amplifier hierarchy of high-speed analog signal-conditioning ICs for low-voltage precision and signal-chain designs.

An operational amplifier is an analog integrated circuit that provides high open-loop gain while processing a differential input signal. The OPA350 family adds rail-to-rail input and output capability, allowing signals to operate close to the supply rails. This rail-to-rail behavior makes it useful in battery-powered equipment, low-voltage sensor interfaces, audio paths, communication equipment, and control systems where conventional non-rail-to-rail amplifiers would clip or restrict headroom.

Key features include 5 nV/√Hz noise density, 38 MHz gain-bandwidth product, and 22 V/µs slew rate. The amplifier operates from a 2.7 V to 5.5 V single supply, and its input common-mode range extends approximately 300 mV below ground and 300 mV above the positive supply. The CMOS implementation also supports low-voltage operation while preserving high-speed transient performance needed for ADC drive and active filtering.

OPA350 series devices are optimized for driving sampling analog-to-digital converters, cell-phone power-amplifier control loops, and video-processing systems. The manufacturer identifies 75-ohm video-drive capability as an application area. Its combination of low noise, wide bandwidth, and rail-to-rail swing supports signal chains where both small-signal fidelity and large-signal linearity are important.

Typical uses include low-voltage ADC input stages, precision current sensing, audio preamplification, active filters, and high-speed control loops. The 38 MHz bandwidth provides useful margin when filtering higher-frequency signals, while the low 5 nV/√Hz noise density helps preserve weak-signal integrity. Slew rate must be checked against the amplitude and bandwidth requirements of the largest intended output waveform.

For layout, place input, feedback, and decoupling components close to their associated pins, and use a short, low-inductance ground return. Maintain a stable feedback network and avoid routing high-impedance input traces beside digital or switching-current paths. The low-voltage operating range does not eliminate the need for supply filtering, particularly when the amplifier is used immediately before a sampling ADC.

This page combines manufacturer specifications, package and pin information, practical application guidance, and structured comparisons with pin-compatible operational-amplifier alternatives to support faster component selection and board-level implementation.

Bộ thay thế dễ dàng lắp đặt cho OPA350UA — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với OPA350UA (cùng hình factor và footprint) — khác nhau ở Gain-Bandwidth Product, Package, Slew Rate, Input Common-Mode Range, Supply Voltage Range.

Texas Instruments
Gain-Bandwidth Product: 1 MHz
Package: 8-pin SOIC (D)
Slew Rate: 0.8 V/µs
So sánh với OPA350UA →
Texas Instruments
Gain-Bandwidth Product: 44 MHz
So sánh với OPA350UA →

OPA351UA

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 8-pin SOIC
Gain-bandwidth product is 38 MHz, matching OPA350UA; remaining functional differences require comparison of the individual data sheets

📋 Tham chiếu thay thế (không có trong danh mục)

OPA353UA

✅ Drop-In
Texas Instruments
📦 8-pin SOIC
Single operational amplifier · 5.5 V · 44 MHz · 7 nV/√Hz · 22 V/µs

Liên hệ để biết giá

Xem tài liệu →

OPA300UA

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 8-pin SOIC
Gain-bandwidth product is 50 MHz versus 38 MHz, approximately 32% higher, with lower-power operating characteristics

📋 Tham chiếu thay thế (không có trong danh mục)

OPA310UA

✅ Drop-In ⚠️ Thông số chưa được xác minh
📦 8-pin SOIC
Gain-bandwidth product is 35 MHz versus 38 MHz, approximately 8% lower, while retaining a similar low-voltage CMOS architecture

📋 Tham chiếu thay thế (không có trong danh mục)

ADA4661ARZ

✅ Drop-In
📦 8-pin SOIC
Gain-bandwidth product is 18 MHz versus 38 MHz, approximately 53% lower, so bandwidth-sensitive designs require simulation and signal-integrity review

📋 Tham chiếu thay thế (không có trong danh mục)

OPA350UA Tỷ lệ tối đa & tính chất điện

Amplifier Type Single operational amplifier
Cấu trúc Rail-to-rail input and output CMOS
Number of Circuits 1 circuit
Gain-Bandwidth Product 38 MHz
Slew Rate 22 V/µs
Input Noise Density 5 nV/√Hz
Supply Voltage Range 2.7 V to 5.5 V
Supply Type Single supply
Input Common-Mode Range Approximately 300 mV below ground to 300 mV above positive supply
Output Swing Rail-to-rail
Input Type Rail-to-rail
Hộp 8-pin SOIC
Kiểu lắp đặt Surface mount

Hướng dẫn cấu hình chân OPA350UA 8-pin soic

Cấu hình chân cho OPA350UA (8-pin soic gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.

Bảng cấu hình chân 8-pin soic cho OPA350UA

Không có dữ liệu chân cụ thể sẵn có cho OPA350UA.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

OPA350UA phù hợp cho 6 Áp dụngs: Sampling ADC Input Driver, Low-Noise Audio Preamplifier, Cell-Phone Power Amplifier Control Loop, Precision Current Sensing, Video Signal Conditioning, Active Analog Filter.

⚡

Sampling ADC Input Driver

The OPA350UA fits low-voltage ADC front ends because its 38 MHz gain-bandwidth product and 22 V/µs slew rate preserve signal amplitude and edge performance beyond the converter’s useful bandwidth. The 5 nV/√Hz input-noise density is also favorable for weak signals where analog gain is limited. Place the amplifier close to the ADC input and keep the feedback network compact to reduce parasitic capacitance and improve settling. The 2.7 V to 5.5 V operating range supports 3.3 V and 5 V converter rails, while rail-to-rail input and output behavior reduces signal-headroom constraints. Check the converter’s settling requirements, input capacitance, and required gain before finalizing the filter and feedback values.

🎧

Low-Noise Audio Preamplifier

The OPA350UA is suitable for low-noise audio preamplification because its 5 nV/√Hz input-noise density reduces the amplifier’s contribution to weak-signal noise, while its 38 MHz bandwidth provides ample margin for audio control and filtering stages. Rail-to-rail input and output operation supports signals that approach the supply limits, and the 22 V/µs slew rate improves handling of larger transient waveforms. Use stable feedback ratios appropriate for the required gain and frequency response. Resistor thermal noise and input-bias-current error can dominate at high source impedances, so the complete signal path should be evaluated rather than relying on the 5 nV/√Hz figure alone.

📱

Cell-Phone Power Amplifier Control Loop

OPA350UA is identified by Texas Instruments for cell-phone power-amplifier control loops, where a high-speed amplifier can respond quickly to envelope or feedback-control signals. Its 38 MHz gain-bandwidth product and 22 V/µs slew rate help minimize delay in the control path, while the 5 nV/√Hz noise density can preserve small feedback signals. The single-supply operation from 2.7 V to 5.5 V aligns with compact portable-system rails. Keep the control trace short, provide local supply bypassing, and verify phase margin and loop stability with the actual compensation network before deployment.

🏭

Precision Current Sensing

OPA350UA can amplify the small differential voltage generated by a low-value shunt resistor in low-voltage current-measurement systems. Its low 5 nV/√Hz input-noise density limits the amplifier’s voltage-noise contribution, while rail-to-rail input and output operation helps use the available measurement range in a 2.7 V to 5.5 V system. The 38 MHz bandwidth allows the amplifier to respond to relatively fast current transients. Use a Kelvin connection from the shunt to reduce parasitic voltage pickup, and verify offset, bias-current error, common-mode limits, and shunt heating against the required measurement accuracy.

📺

Video Signal Conditioning

OPA350UA is suitable for video-processing signal conditioning because its 38 MHz bandwidth, 22 V/µs slew rate, and rail-to-rail output support 75-ohm video-drive applications identified by the manufacturer. The amplifier can condition a video waveform before routing it to another stage, with sufficient bandwidth for common baseband video signals and higher-frequency transitions. Preserve the source and termination geometry, keep the feedback loop compact, and maintain a continuous return path to reduce ringing. If the circuit processes standard-definition, high-definition, or composite video, check the required gain, output amplitude, settling time, and channel-to-channel matching before production release.

🔧

Active Analog Filter

OPA350UA can implement active filters in low-voltage instrumentation because its 38 MHz gain-bandwidth product provides useful loop gain above the filter corner frequency, and the 22 V/µs slew rate supports signal transitions with reduced distortion. The 5 nV/√Hz noise density is valuable when filtering small analog signals, while the single 2.7 V to 5.5 V supply simplifies portable-system power design. Select feedback resistors and capacitors for the required transfer function, then verify phase margin and gain peaking with the amplifier’s exact gain-noise curve. Place filter components close to the package and provide local bypassing to reduce instability caused by long feedback traces.

What is the operating voltage of OPA350UA?
The OPA350UA operates from a single supply of 2.7 V to 5.5 V. According to the Texas Instruments OPA350 data sheet, it is optimized for low-voltage operation while retaining rail-to-rail input and output behavior. Its input common-mode range extends approximately 300 mV below ground and 300 mV above the positive supply, which is useful in 3.3 V and 5 V systems where signal headroom is limited.
What are the key specifications of OPA350UA that engineers should know?
The OPA350UA is a single CMOS operational amplifier with a 38 MHz gain-bandwidth product, 22 V/µs slew rate, and 5 nV/√Hz input-noise density. Texas Instruments identifies rail-to-rail input and output operation and a 2.7 V to 5.5 V supply range. These figures position it between general-purpose low-noise amplifiers and much faster mixed-signal or RF amplifiers, making it appropriate for ADC drive, filtering, and precision low-voltage signal chains.
Where can I download the OPA350UA datasheet PDF?
The OPA350UA datasheet can be obtained from the Texas Instruments OPA350 product page or its linked data sheet at ti.com/lit/gpn/OPA350. The document describes the OPA350 family, including the 38 MHz gain-bandwidth product, 22 V/µs slew rate, 5 nV/√Hz noise density, electrical characteristics, package information, and application guidance. The official OPA350UA ordering page links to the same technical documentation.
Is OPA350UA suitable for driving a sampling ADC?
Yes, the OPA350UA is specifically optimized for driving sampling analog-to-digital converters. Its 38 MHz gain-bandwidth product and 22 V/µs slew rate provide useful dynamic performance, while the 5 nV/√Hz input-noise density supports low-noise signal acquisition. The TI data sheet also identifies cell-phone power-amplifier control loops and video processing as suitable applications.
What is the difference between OPA350UA and OPA353UA?
The OPA353UA is a closely related Texas Instruments high-speed, single-supply operational amplifier with a nominal gain-bandwidth product of 44 MHz, compared with 38 MHz for the OPA350UA. That is approximately a 16% increase in bandwidth. Both devices are available in an 8-pin SOIC configuration, but the exact OPA353UA electrical characteristics should be checked against the OPA350UA requirements before treating it as a drop-in replacement.
What is the best drop-in replacement for OPA350UA?
The closest listed drop-in candidates are the OPA351UA and OPA353UA because they use the same 8-pin SOIC format and belong to the same high-speed, low-voltage CMOS amplifier family. The OPA351UA retains the 38 MHz nominal bandwidth of the OPA350UA, while the OPA353UA offers approximately 44 MHz. Confirm supply range, common-mode range, output swing, stability, and pin functions against the OPA350 data sheet before substitution.
Can ADA4661ARZ replace OPA350UA in an 8-pin SOIC design?
The ADA4661ARZ is a candidate for evaluation in an 8-pin SOIC signal path, but it should not be treated as an automatic OPA350UA replacement. Its nominal gain-bandwidth product is lower than the OPA350UA's 38 MHz, and its rail-to-rail behavior and output-drive characteristics may differ. Verify input bias current, common-mode range, output swing, noise, stability, and required closed-loop gain before approving the substitution.
When should I choose OPA350UA instead of OPA300UA?
Choose OPA350UA when the design benefits directly from its 38 MHz gain-bandwidth product, 22 V/µs slew rate, and 5 nV/√Hz noise density in a 2.7 V to 5.5 V single-supply system. The OPA300UA may be suitable where lower power consumption is more important than maximum speed. Both use an 8-pin SOIC configuration, so check closed-loop stability and output-drive requirements before selecting the lower-power option.
Is OPA350UA the same as OPA351UA?
No. The OPA350UA and OPA351UA share the same 8-pin SOIC format and high-speed, low-voltage CMOS family, but they are different orderable devices. The OPA351UA retains a nominal 38 MHz gain-bandwidth product, while functional details such as electrical limits and feature flags can differ between family members. Use the individual data sheet for the exact MPN when preparing a production bill of materials.
How much noise does OPA350UA contribute for a low-level signal amplifier?
The OPA350UA has an input-noise density of 5 nV/√Hz according to the Texas Instruments data sheet. In a bandwidth-limited amplifier, input-referred noise is strongly dependent on the closed-loop gain, noise-gain curve, resistor choice, and the measurement bandwidth. The 5 nV/√Hz figure is therefore most useful during front-end comparison, while the complete noise calculation should also include resistor and current-noise contributions.
Where can I find the OPA350UA pinout and 8-pin SOIC layout?
The OPA350UA pin assignments and package drawing are located in the pin-configuration and mechanical-drawing sections of the Texas Instruments OPA350 data sheet. The device is an 8-pin SOIC operational amplifier. Before routing a PCB, compare the data-sheet pin numbers with the selected package library and confirm whether a thermal-pad or exposed-connection variant is being used; the standard OPA350UA is identified as an 8-SOIC device.
What layout practices matter for a high-speed OPA350UA design?
Place the amplifier input and feedback components close to their pins and keep the input trace short to minimize parasitic capacitance and susceptibility to interference. Route the return current through a continuous ground plane, and keep switching-regulator and high-current paths away from the input node. For ADC drive, use a short, impedance-controlled connection and place any isolation or filtering components where their intended bandwidth remains valid.
Where can I buy OPA350UA online and check its current availability?
Use the Request a Quote form on this page to request current OPA350UA availability, lead time, and a quotation for the exact 8-pin SOIC orderable MPN. The Request a Quote workflow lets the buyer specify quantity and packaging requirements without relying on a static price. Engineers should include the full OPA350UA suffix and the required reel or tube configuration in the request.
What is the current price of OPA350UA?
The current commercial price for OPA350UA should be obtained through the Request a Quote form on this page. Submit the exact MPN, quantity, and packaging method so the quotation reflects current inventory, lead time, and order conditions. This approach avoids presenting an outdated distributor-catalog figure as a live market quotation for this specific 8-pin SOIC device.
What is the lead time for OPA350UA?
Request the current OPA350UA lead time through the Request a Quote form on this page. Include the required quantity and whether the part must be supplied in tape-and-reel or another approved package format. Lead time can vary with order volume, packaging, and current component availability, so an up-to-date manufacturing commitment should be obtained for the exact order.
Is OPA350UA RoHS and REACH compliant?
The Texas Instruments product materials for the OPA350 family support a lead-free and RoHS-oriented manufacturing approach, but the exact compliance status for OPA350UA should be confirmed against the current manufacturer declaration or product page. Request the applicable material-compliance documentation for the lot if your procurement process requires a certificate. Do not infer REACH or conflict-minerals status solely from the package type.

Dữ liệu tham khảo kỹ thuật cho OPA350UA — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose OPA350UA when a low-voltage, single-supply design needs the combination of 5 nV/√Hz noise, 38 MHz bandwidth, 22 V/µs slew rate, and rail-to-rail input and output operation in an 8-pin SOIC. OPA351UA is the closest same-family candidate when matching the nominal bandwidth is the priority, while OPA353UA offers about 16% more bandwidth for designs needing faster edges. OPA300UA is attractive when lower power is more important than maximum bandwidth. OPA310UA is a lower-bandwidth alternative at approximately 35 MHz and should be selected when its power and noise characteristics better match the application. ADA4661ARZ provides a cross-manufacturer 8-pin SOIC option, but its nominal 18 MHz bandwidth is substantially below the OPA350UA and requires careful settling and stability verification. Before approving any substitution, compare supply range, common-mode range, output swing, input bias current, offset voltage, noise, stability, and capacitive-load behavior.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này OPA351UA OPA353UA OPA300UA OPA310UA ADA4661ARZ
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments Texas Instruments Analog Devices
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Amplifier Type Single CMOS operational amplifier Single operational amplifier Single operational amplifier Single operational amplifier Single operational amplifier Single operational amplifier
Gain-Bandwidth Product 38 MHz 38 MHz 44 MHz 50 MHz 35 MHz 18 MHz
Primary Application ADC drive, control loops, and video processing Low-voltage high-speed signal conditioning High-speed single-supply signal conditioning Low-power high-speed signal conditioning Low-noise high-speed signal conditioning Precision low-voltage signal conditioning

Bảo phân biệt quan trọng

  • Balanced low-noise and high-speed performance (vsOPA351UA)
  • More bandwidth for faster edge response (vsOPA353UA)
  • Lower-power design option in the same pin-compatible family (vsOPA300UA)

Ghi chú thiết kế

Place input, feedback, and bypass components directly adjacent to the OPA350UA pins. Keep the noninverting input and inverting input routes short, particularly for high-gain or high-frequency configurations. Connect the decoupling capacitor to a low-impedance ground plane, and avoid routing the input node alongside regulators, clock lines, or switching-node traces. Parasitic capacitance introduced by long PCB traces can reduce phase margin and alter the effective feedback factor.

Use the 38 MHz gain-bandwidth product and 22 V/µs slew rate as design limits, not guarantees of usable closed-loop bandwidth. The maximum practical bandwidth depends on noise gain, feedback impedance, capacitive loading, and loop stability. When driving an ADC or cable, evaluate settling behavior with the actual load and consider a small isolation resistor near the amplifier output if capacitive loading could cause peaking.

The OPA350UA is intended for a single supply from 2.7 V to 5.5 V. Provide local high-frequency decoupling close to the supply pins and ensure the source can support output-current peaks without disturbing the amplifier's signal headroom. Rail-to-rail behavior reduces output-swing restrictions, but it does not eliminate supply noise, and the 5 nV/√Hz input-noise specification cannot compensate for noisy supply rails or poorly connected shunt resistors.

Do not assume that every 8-pin SOIC high-speed amplifier is interchangeable with the OPA350UA. Confirm pin orientation, supply pins, input and output assignments, common-mode limits, output swing, stability, and offset behavior from the exact replacement data sheet. For ADC applications, also verify output settling and capacitive-load drive. A footprint match alone is insufficient to guarantee equivalent signal performance.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

Exact RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations for OPA350UA were not identified. Obtain current manufacturer documentation before making a compliance claim.

Dữ liệu được xác minh vào: 2026-11-14 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

opa350ua datasheet OPA350UA pinout OPA350UA datasheet pdf Texas Instruments OPA350UA OPA350UA 38MHz operational amplifier OPA350UA 5 nV noise OPA350UA 8-SOIC OPA350UA ADC driver OPA350UA vs OPA353UA OPA350UA equivalent OPA350UA replacement OPA350UA price OPA350UA stock OPA350UA video signal conditioning

Các bộ phận và thuật ngữ liên quan

Texas Instruments OPA350UA OPA350 OPA351UA OPA353UA OPA300UA OPA310UA ADA4661ARZ operational amplifier CMOS operational amplifier single-supply amplifier rail-to-rail input rail-to-rail output gain-bandwidth product slew rate input-noise density common-mode voltage range ADC driver active filter audio preamplifier current-sense amplifier video signal conditioning 8-pin SOIC SOIC package family surface-mount package
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ