OPA830ID - 110MHz Wideband Op Amp | Texas Instruments
MPN: OPA830ID ✓ فعالOPA830ID جائزہ
A wideband operational amplifier is a voltage-feedback amplifier designed for signal amplification over a broad frequency range. The OPA830 belongs to the amplifier IC hierarchy, where its 110 MHz gain-bandwidth product and approximately 9.2 nV/√Hz input voltage noise support high-speed, low-noise signal conditioning. This makes the device relevant to data acquisition, communications, instrumentation, and precision analog systems where bandwidth and signal fidelity must coexist with low power consumption.
Key features include a 110 MHz gain-bandwidth product, a 9.2 nV/√Hz input voltage-noise density, and an input common-mode range that extends below the negative supply. The amplifier can operate from 3 V, 5 V, ±5 V, or +10 V, reducing the number of required supply arrangements. Its complementary common-emitter output stage produces an output swing to within 25 mV of the supply rails, providing useful output range for low-voltage signal chains.
OPA830ID is a single-amplifier device intended primarily for fixed-gain line-driver applications. Texas Instruments also identifies OPA832 as an option for fixed-gain line-driver designs when its particular gain and performance characteristics are better suited to the system. The OPA830's voltage-feedback architecture makes feedback-network selection and stability assessment important when setting closed-loop gain.
Typical uses include low-power signal buffering, communications-interface signal conditioning, precision measurement front ends, and mixed-signal subsystem interfacing. The 110 MHz bandwidth can preserve higher-frequency content in video, data-conversion, and control paths, while the low-noise specification supports high-dynamic-range analog stages. The 8-pin SOIC format also supports conventional surface-mount assembly and hand-soldering workflows.
When designing around the OPA830ID, preserve the usable input and output ranges by checking signal swing against the actual supply voltage and load. Decoupling capacitors should be placed close to the supply pins, and feedback traces should remain short to minimize parasitic effects. Stability, gain-bandwidth trade-offs, and permissible output loading should be evaluated using the manufacturer datasheet rather than inferred from the nominal 110 MHz figure.
This page combines the exact orderable MPN, manufacturer documentation, package information, sourcing details, application guidance, and an engineering comparison for engineers evaluating the OPA830ID for low-power wideband amplification.
کے لیے ڈراپ اِن متبادل OPA830ID — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں OPA830ID (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Amplifier Type, Input Voltage Noise Density, Number of Channels, Package.
OPA828ID
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ✓ اسٹاک میں
$1.75 / یونٹ
ڈیٹا شیٹ دیکھیں →OPA830ID زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Amplifier Type | Voltage-feedback operational amplifier |
| Number of Channels | 1 circuit |
| Gain-Bandwidth Product | 110 MHz |
| Single-Supply Operation | 3 V or 5 V |
| Additional Supply Configurations | ±5 V or +10 V |
| Input Voltage Noise Density | 9.2 nV/√Hz |
| Input Common-Mode Range | Extends below the negative supply and to within 1.7 V of the positive supply |
| Output Swing | Within 25 mV of either supply |
| Output Stage | Complementary common-emitter |
| Primary Application | Fixed-gain line driver |
| پیکیج | 8-SOIC, 0.154 inch body width, 3.90 mm |
| ماؤنٹنگ ٹائپ | Surface mount |
OPA830ID پن کنفیگریشن
| پن 1 | NC — Not connected |
| پن 2 | IN- — Inverting input |
| پن 3 | IN+ — Non-inverting input |
| پن 4 | V- — Negative supply connection |
| پن 5 | NC — Not connected |
| پن 6 | OUT — Amplifier output |
| پن 7 | V+ — Positive supply connection |
| پن 8 | NC — Not connected |
عام استعمالات
OPA830ID کے لیے موزوں ہے 6 ایپلیکیشنs: Wideband Signal Buffering, Communications Line Driver, Precision Data-Acquisition Front End, Instrumentation Signal Conditioning, Video Signal Path, Low-Voltage Mixed-Signal Interface.
Wideband Signal Buffering
OPA830ID fits wideband buffering because its 110 MHz gain-bandwidth product preserves high-frequency signal content while its low-power operation suits compact analog systems. According to the Texas Instruments OPA830 datasheet, the amplifier also accepts single 3 V or 5 V supplies, allowing it to buffer signals between low-voltage converter and ADC stages. Place the device in a voltage-feedback buffer configuration with short feedback tracks, check the load presented by the following stage, and confirm stability with the intended output capacitance. The 9.2 nV/√Hz input voltage-noise density helps preserve dynamic range when buffering weak source signals.
تجویز کردہ
Communications Line Driver
OPA830ID is appropriate for communications signal-conditioning paths requiring a 110 MHz gain-bandwidth product and a flexible supply arrangement. Texas Instruments describes the device for fixed-gain line-driver use, allowing the gain to be established with a feedback network rather than relying on a very high closed-loop gain. Operation from 3 V or 5 V supports compact communications equipment, while the output stage reaches to within 25 mV of either supply. Engineers should preserve the usable common-mode range, account for cable or termination loading, and verify stability against the complete output network rather than only the nominal bandwidth.
تجویز کردہ
Precision Data-Acquisition Front End
OPA830ID can serve in a precision data-acquisition front end when a wideband amplifier must coexist with a low-noise input stage. Its 9.2 nV/√Hz input voltage-noise density supports measurements in which amplifier noise could otherwise limit dynamic range, and the 110 MHz gain-bandwidth product is useful ahead of fast converters or sampling systems. The input range extending below the negative supply can simplify some sensor-interface topologies, but the exact input amplitude must remain within the manufacturer limits. Use short, guarded signal paths and select feedback resistors and capacitor values according to the target gain and signal bandwidth.
تجویز کردہ
Instrumentation Signal Conditioning
OPA830ID is well suited to instrumentation circuits that must amplify small-amplitude signals without losing bandwidth. The 110 MHz gain-bandwidth product gives designers substantial loop gain across the signal band, and the 9.2 nV/√Hz voltage-noise density helps maintain sensitivity at low signal levels. Single 3 V or 5 V operation can simplify portable or embedded test equipment, while ±5 V support offers additional common-mode flexibility where the instrumentation requires it. Check input bias-current effects at the source, use a stable feedback network, and validate output settling and loading for the instrumentation's required measurement bandwidth.
تجویز کردہ
Video Signal Path
OPA830ID can operate in video and other high-bandwidth analog paths because its 110 MHz gain-bandwidth product is well suited to preserving rapidly changing waveforms. The amplifier's output swing to within 25 mV of either supply improves utilization of low-voltage rails, while operation from 3 V or 5 V supports compact consumer and industrial video circuitry. The actual usable bandwidth depends on the closed-loop gain and feedback impedance, so designers should not equate the 110 MHz gain-bandwidth figure directly with an output bandwidth specification. Maintain short signal paths, provide local supply decoupling, and confirm stability with the source and load capacitance present on the assembled board.
تجویز کردہ
Low-Voltage Mixed-Signal Interface
OPA830ID fits low-voltage mixed-signal interfaces where a converter, sensor, or communications front end drives a downstream analog block. Single 3 V and 5 V operation aligns with common digital-system rails, and the input range extending below the negative supply provides flexibility around zero-centered signals. Its 9.2 nV/√Hz input-noise density is valuable when the source level is small enough for amplifier noise to affect the result. Place supply bypass capacitors close to the device, avoid long high-impedance feedback routes, and verify the input common-mode range and output swing against the complete signal excursion before production use.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا OPA830ID — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | OPA828ID |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC |
| Amplifier Type | Single voltage-feedback operational amplifier | Single voltage-feedback operational amplifier |
| Gain-Bandwidth Product | 110 MHz | 105 MHz |
| Number of Channels | 1 circuit | 1 circuit |
اہم امتیازی خصوصیات
- Higher gain-bandwidth product in the same 8-pin SOIC format (بمقابلہOPA828ID)
- Documented low-noise wideband operation (بمقابلہOPA828ID)
- Flexible single- and dual-supply operation (بمقابلہOPA828ID)
ڈیزائن نوٹس
Place the supply bypass capacitors immediately adjacent to the V+ and V- pins and keep the supply current loop as compact as possible. For a high-frequency layout, route the amplifier output directly to the load or next-stage input rather than through a long unprotected trace. Keep the inverting-input and feedback components close to pins 2 and 6 so parasitic capacitance does not unexpectedly alter the closed-loop response. Use a continuous ground reference beneath the device where board density permits.
Use the 110 MHz gain-bandwidth figure as a loop-gain parameter rather than treating it as a guaranteed closed-loop bandwidth at every gain. Select the feedback resistors to limit parasitic capacitance and ensure the complete source, feedback, and load network remains stable. If the OPA830ID drives cable, ADC input capacitance, or a long trace, check output loading and overshoot before production. This is particularly important because the low-power wideband topology can make PCB parasitics more significant than they are in a slower precision amplifier.
Do not assume the full negative rail is always a valid input voltage, and do not design output signals to exceed the stated 25 mV supply-rail margin. The usable input and output ranges depend on supply voltage and operating conditions, so verify the relevant limits in the OPA830 datasheet. Also avoid using the gain-bandwidth product alone to estimate settling time or output bandwidth. A gain of two or greater requires particular attention to feedback-network impedance, noise gain, and capacitive-load stability.
تعمیل کی معلومات
No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement is stated for the exact OPA830ID ordering variant. AEC-Q100 is not applicable to this general-purpose amplifier package.