Texas Instruments

OPA830ID - 110MHz Wideband Op Amp | Texas Instruments

料号: OPA830ID ✓ 量产中
3 V or 5 V Vdss 8-SOIC, 0.154 inch body width, 3.90 mm Package
最小起订量: 1 |

OPA830ID 概述

Texas Instruments OPA830ID is a low-power, single-supply, wideband, voltage-feedback operational amplifier with a 110 MHz gain-bandwidth product, packaged in an 8-pin SOIC. It operates from a single 3 V or 5 V supply and also supports ±5 V or +10 V supplies. Its input range extends below the negative supply and to within 1.7 V of the positive supply, while the output can swing to within 25 mV of either supply.

A wideband operational amplifier is a voltage-feedback amplifier designed for signal amplification over a broad frequency range. The OPA830 belongs to the amplifier IC hierarchy, where its 110 MHz gain-bandwidth product and approximately 9.2 nV/√Hz input voltage noise support high-speed, low-noise signal conditioning. This makes the device relevant to data acquisition, communications, instrumentation, and precision analog systems where bandwidth and signal fidelity must coexist with low power consumption.

Key features include a 110 MHz gain-bandwidth product, a 9.2 nV/√Hz input voltage-noise density, and an input common-mode range that extends below the negative supply. The amplifier can operate from 3 V, 5 V, ±5 V, or +10 V, reducing the number of required supply arrangements. Its complementary common-emitter output stage produces an output swing to within 25 mV of the supply rails, providing useful output range for low-voltage signal chains.

OPA830ID is a single-amplifier device intended primarily for fixed-gain line-driver applications. Texas Instruments also identifies OPA832 as an option for fixed-gain line-driver designs when its particular gain and performance characteristics are better suited to the system. The OPA830's voltage-feedback architecture makes feedback-network selection and stability assessment important when setting closed-loop gain.

Typical uses include low-power signal buffering, communications-interface signal conditioning, precision measurement front ends, and mixed-signal subsystem interfacing. The 110 MHz bandwidth can preserve higher-frequency content in video, data-conversion, and control paths, while the low-noise specification supports high-dynamic-range analog stages. The 8-pin SOIC format also supports conventional surface-mount assembly and hand-soldering workflows.

When designing around the OPA830ID, preserve the usable input and output ranges by checking signal swing against the actual supply voltage and load. Decoupling capacitors should be placed close to the supply pins, and feedback traces should remain short to minimize parasitic effects. Stability, gain-bandwidth trade-offs, and permissible output loading should be evaluated using the manufacturer datasheet rather than inferred from the nominal 110 MHz figure.

This page combines the exact orderable MPN, manufacturer documentation, package information, sourcing details, application guidance, and an engineering comparison for engineers evaluating the OPA830ID for low-power wideband amplification.

直接替换替代料: OPA830ID ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: OPA830ID (相同外形与封装尺寸) ——差异在于 Amplifier Type, Input Voltage Noise Density, Number of Channels, Package.

Texas Instruments
Amplifier Type: JFET-input operational amplifier
Input Voltage Noise Density: 4 nV/√Hz at 1 kHz
Number of Channels: 1
对比 OPA830ID →

OPA828ID

✅ 直接替换 ⚠️ 规格未核验
Texas Instruments
📦 8-SOIC
JFET-input operational amplifier · 1 · 45 MHz · 150 V/us · 4 nV/√Hz at 1 kHz · 60 nVRMS · 1 pA (typical) · 50 uV

✓ 有现货

$1.75 / 个

查看数据手册 →

OPA830ID 最大额定值与电气特性

Amplifier Type Voltage-feedback operational amplifier
Number of Channels 1 circuit
Gain-Bandwidth Product 110 MHz
Single-Supply Operation 3 V or 5 V
Additional Supply Configurations ±5 V or +10 V
Input Voltage Noise Density 9.2 nV/√Hz
Input Common-Mode Range Extends below the negative supply and to within 1.7 V of the positive supply
Output Swing Within 25 mV of either supply
Output Stage Complementary common-emitter
Primary Application Fixed-gain line driver
封装 8-SOIC, 0.154 inch body width, 3.90 mm
安装类型 Surface mount

OPA830ID 引脚配置

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
引脚 1 NC — Not connected
引脚 2 IN- — Inverting input
引脚 3 IN+ — Non-inverting input
引脚 4 V- — Negative supply connection
引脚 5 NC — Not connected
引脚 6 OUT — Amplifier output
引脚 7 V+ — Positive supply connection
引脚 8 NC — Not connected

典型应用

OPA830ID 适用于 6 应用s: Wideband Signal Buffering, Communications Line Driver, Precision Data-Acquisition Front End, Instrumentation Signal Conditioning, Video Signal Path, Low-Voltage Mixed-Signal Interface.

🔧

Wideband Signal Buffering

OPA830ID fits wideband buffering because its 110 MHz gain-bandwidth product preserves high-frequency signal content while its low-power operation suits compact analog systems. According to the Texas Instruments OPA830 datasheet, the amplifier also accepts single 3 V or 5 V supplies, allowing it to buffer signals between low-voltage converter and ADC stages. Place the device in a voltage-feedback buffer configuration with short feedback tracks, check the load presented by the following stage, and confirm stability with the intended output capacitance. The 9.2 nV/√Hz input voltage-noise density helps preserve dynamic range when buffering weak source signals.

🌐

Communications Line Driver

OPA830ID is appropriate for communications signal-conditioning paths requiring a 110 MHz gain-bandwidth product and a flexible supply arrangement. Texas Instruments describes the device for fixed-gain line-driver use, allowing the gain to be established with a feedback network rather than relying on a very high closed-loop gain. Operation from 3 V or 5 V supports compact communications equipment, while the output stage reaches to within 25 mV of either supply. Engineers should preserve the usable common-mode range, account for cable or termination loading, and verify stability against the complete output network rather than only the nominal bandwidth.

📊

Precision Data-Acquisition Front End

OPA830ID can serve in a precision data-acquisition front end when a wideband amplifier must coexist with a low-noise input stage. Its 9.2 nV/√Hz input voltage-noise density supports measurements in which amplifier noise could otherwise limit dynamic range, and the 110 MHz gain-bandwidth product is useful ahead of fast converters or sampling systems. The input range extending below the negative supply can simplify some sensor-interface topologies, but the exact input amplitude must remain within the manufacturer limits. Use short, guarded signal paths and select feedback resistors and capacitor values according to the target gain and signal bandwidth.

🖥️

Instrumentation Signal Conditioning

OPA830ID is well suited to instrumentation circuits that must amplify small-amplitude signals without losing bandwidth. The 110 MHz gain-bandwidth product gives designers substantial loop gain across the signal band, and the 9.2 nV/√Hz voltage-noise density helps maintain sensitivity at low signal levels. Single 3 V or 5 V operation can simplify portable or embedded test equipment, while ±5 V support offers additional common-mode flexibility where the instrumentation requires it. Check input bias-current effects at the source, use a stable feedback network, and validate output settling and loading for the instrumentation's required measurement bandwidth.

📺

Video Signal Path

OPA830ID can operate in video and other high-bandwidth analog paths because its 110 MHz gain-bandwidth product is well suited to preserving rapidly changing waveforms. The amplifier's output swing to within 25 mV of either supply improves utilization of low-voltage rails, while operation from 3 V or 5 V supports compact consumer and industrial video circuitry. The actual usable bandwidth depends on the closed-loop gain and feedback impedance, so designers should not equate the 110 MHz gain-bandwidth figure directly with an output bandwidth specification. Maintain short signal paths, provide local supply decoupling, and confirm stability with the source and load capacitance present on the assembled board.

🧩

Low-Voltage Mixed-Signal Interface

OPA830ID fits low-voltage mixed-signal interfaces where a converter, sensor, or communications front end drives a downstream analog block. Single 3 V and 5 V operation aligns with common digital-system rails, and the input range extending below the negative supply provides flexibility around zero-centered signals. Its 9.2 nV/√Hz input-noise density is valuable when the source level is small enough for amplifier noise to affect the result. Place supply bypass capacitors close to the device, avoid long high-impedance feedback routes, and verify the input common-mode range and output swing against the complete signal excursion before production use.

What are the key specifications of OPA830ID that engineers should know?
OPA830ID is a single-channel, 110 MHz, low-power voltage-feedback operational amplifier in an 8-pin SOIC. According to the Texas Instruments OPA830 datasheet, it supports single 3 V or 5 V supplies as well as ±5 V and +10 V operation. Its input voltage-noise density is 9.2 nV/√Hz, its input range extends below the negative rail, and its output can reach within 25 mV of either supply. These characteristics make it suitable for wideband signal conditioning, fixed-gain line driving, communications, instrumentation, and data-acquisition front ends where response speed and low noise are both important.
Where can I download the OPA830ID datasheet PDF?
The official OPA830ID datasheet PDF is available from Texas Instruments at https://www.ti.com/lit/ds/symlink/opa830.pdf. The document describes the low-power, single-supply, wideband voltage-feedback amplifier, including its 110 MHz gain-bandwidth product, 3 V and 5 V single-supply operation, input-range behavior, and output-swing characteristics. Use the manufacturer document for the authoritative pin descriptions, recommended operating conditions, electrical characteristics, and application guidance. The OPA830ID is the 8-pin SOIC ordering variant, while the same family is also offered in a smaller SOT23-5 package.
Where can I find the OPA830ID pinout?
The OPA830ID pinout is shown in the manufacturer datasheet at https://www.ti.com/lit/ds/symlink/opa830.pdf. Its 8-pin SOIC connection includes the inverting input, non-inverting input, positive supply, negative supply, output, and designated no-connect positions. When assigning PCB tracks, use the pin-description table in that document and preserve the exposed functional requirements of the SOIC footprint. The package library entry used for this page is the standard 8-pin SOIC, so its eight numbered positions correspond directly to the manufacturer package drawing.
What supply voltages can OPA830ID operate from?
OPA830ID can operate from a single 3 V or 5 V supply and can also be used with ±5 V or +10 V supplies. According to the Texas Instruments OPA830 datasheet, the input range extends below the negative supply and to within 1.7 V of the positive supply. Designers should verify the actual signal amplitude against these limits because the usable input range is intentionally wider than a conventional rail-to-rail input specification but still depends on the selected supply arrangement. The same wide-range capability supports both compact low-voltage systems and higher-voltage bipolar or single-ended analog circuits.
Is OPA830ID suitable for fixed-gain line-driver applications?
OPA830ID is specifically suitable for fixed-gain line-driver applications because it is a 110 MHz voltage-feedback amplifier with low 9.2 nV/√Hz input voltage noise. Texas Instruments also identifies OPA832 as a device to consider for fixed-gain line drivers, allowing engineers to compare their gain and bandwidth requirements. When using OPA830ID as a line driver, select the feedback network carefully, confirm that the intended signal amplitude remains within the usable output range, and account for loading capacitance so the amplifier maintains the required stability.
What is the input noise of OPA830ID?
OPA830ID has an input voltage-noise density of 9.2 nV/√Hz. According to the Texas Instruments OPA830 product page, this low-noise characteristic supports wide-dynamic-range operation. The value is useful when comparing the amplifier with other wideband op amps because it describes the amplifier's inherent voltage-noise contribution over frequency. Actual receiver noise will also depend on resistor selection, source impedance, bandwidth, and the gain implemented by the feedback network, so the noise-density specification should be combined with the complete signal-chain analysis.
How much output swing does OPA830ID provide?
OPA830ID can swing its output to within 25 mV of either supply under the conditions described in the Texas Instruments OPA830 datasheet. This wide output range is enabled by the complementary common-emitter output stage. The practical swing at a particular voltage and frequency can depend on load and output-current conditions, so designers should consult the relevant datasheet limits rather than treating the 25 mV figure as unconditional. In a low-voltage circuit, leaving this much headroom can improve output utilization while still supporting single 3 V or 5 V operation.
Where can I buy OPA830ID online?
You can request a quote for OPA830ID through the Request a Quote form on this product page. The form is the appropriate route for checking current commercial availability, order quantities, and delivery timing without relying on stale catalog figures. The part is the Texas Instruments 8-SOIC ordering variant of the OPA830 family. Buyers should state the required quantity and destination in the request so the commercial team can return the current quotation and lead time for the exact OPA830ID orderable MPN.
What is the price of OPA830ID?
Use the Request a Quote form on this page for the current OPA830ID quotation. Pricing can change with quantity, market conditions, and fulfillment requirements, so a static figure in an answer may no longer represent the current offer. The quote request should include the required order quantity and delivery destination. The structured pricing information on this page is maintained separately for transaction use, while the form provides the direct route for a current commercial response.
What is the lead time for OPA830ID?
The current OPA830ID lead time should be confirmed through the Request a Quote form on this page. Lead time can vary with order quantity, inventory position, and shipping destination, making it impractical to guarantee a delivery date without a current quotation. One distributor search result describes the part as immediately shippable, but engineers should treat that indication as a point-in-time listing rather than a firm production promise. Include the required quantity and destination in the request for the most useful response.
Is OPA830ID in stock?
Current OPA830ID inventory should be checked through the Request a Quote form on this page. One distributor listing reports thousands of units available and identifies the component as immediately shippable, but stock levels are transient and can change after the listing is captured. The form is the correct channel for confirming availability for a particular order quantity. Specify the required quantity, packaging expectations, and destination so the commercial team can respond against the current inventory position.
OPA830ID vs OPA828ID - which is better for a wideband signal chain?
OPA830ID is the stronger choice when the design specifically requires its documented 110 MHz gain-bandwidth product, 9.2 nV/√Hz input noise, and operation from a single 3 V or 5 V supply. OPA828ID is a relevant same-package family alternative, but the available manufacturer material identifies OPA830 as the low-power, wideband, single-supply option. Final selection should compare the OPA828ID electrical characteristics against the OPA830ID requirements for bandwidth, noise, supply voltage, input range, output swing, stability, and operating temperature rather than relying only on package compatibility.
When should I choose OPA830ID instead of OPA828ID?
Choose OPA830ID when your design benefits from a documented 110 MHz gain-bandwidth product and 9.2 nV/√Hz input voltage-noise density in a low-power, single-supply wideband amplifier. OPA828ID may be appropriate when its electrical characteristics provide a better fit for the required gain, supply arrangement, noise, output swing, or temperature range. Both devices should be reviewed as an SOIC-8 option, but matching the package is only the first step; closed-loop stability, output loading, input bias behavior, and system-level noise determine whether the substitution is electrically acceptable.
Is OPA830ID suitable for communications and instrumentation applications?
OPA830ID is suitable for communications and instrumentation signal paths that need wide bandwidth, low voltage noise, and flexible supply operation. Its 110 MHz gain-bandwidth product preserves higher-frequency signal content, while the 9.2 nV/√Hz input-noise density supports high-dynamic-range measurement stages. Operation from 3 V or 5 V is useful for compact systems, and the input range extending below the negative supply can simplify some interface arrangements. Confirm common-mode limits, output swing, capacitive-load behavior, and stability for the exact gain network before releasing the design.
What can replace OPA830ID?
OPA828ID is a same-manufacturer drop-in candidate for the Texas Instruments OPA830ID because it is offered in the same 8-pin SOIC format, but it must be qualified electrically before substitution. The available replacement search identifies no verified cross-brand equivalent, so unverified competitor parts are not recommended as direct replacements. A valid swap should preserve the SOIC-8 pinout and meet the original bandwidth, supply, input-noise, common-mode, output-swing, slew-rate, stability, and temperature requirements. Confirm the exact OPA828ID suffix and review its manufacturer datasheet.
Can OPA828ID replace OPA830ID without changing the PCB?
OPA828ID can fit the same 8-pin SOIC footprint, which makes PCB changes unnecessary at the package level. However, a footprint-compatible part is only a valid drop-in replacement after its electrical behavior has been checked against the OPA830ID design. Compare supply range, gain-bandwidth product, input noise, offset voltage, bias current, common-mode range, output swing, slew rate, stability with the selected feedback network, and operating-temperature grade. The available OPA830ID documentation supports its 110 MHz bandwidth and 9.2 nV/√Hz noise specifications, which provide the baseline for that qualification.

工程参考数据: OPA830ID ——对比、设计指导和合规信息。

选型指南

Choose OPA830ID when the design needs a low-power, wideband, single-amplifier solution with a documented 110 MHz gain-bandwidth product and 9.2 nV/√Hz input noise. Its 3 V and 5 V single-supply options suit compact mixed-signal equipment, while ±5 V and +10 V operation provides common-mode flexibility for instrumentation and communications. OPA828ID is the relevant same-package alternative when its electrical characteristics, possibly including its 105 MHz gain-bandwidth product, better match the target system or allow a broader supply range. Treat package equivalence as only the first qualification step: review offset, bias current, slew rate, common-mode range, output swing, stability, and temperature limits for OPA828ID against the OPA830ID design. For applications requiring a different pinout, rail-to-rail output behavior, fixed gain, or substantially different noise and bandwidth, redesign around the appropriate amplifier rather than treating a nominal SOIC-8 match as sufficient.

与替代料对比

参数 本产品 OPA828ID
Brand Texas Instruments Texas Instruments
Package 8-SOIC 8-SOIC
Amplifier Type Single voltage-feedback operational amplifier Single voltage-feedback operational amplifier
Gain-Bandwidth Product 110 MHz 105 MHz
Number of Channels 1 circuit 1 circuit

关键差异点

  • Higher gain-bandwidth product in the same 8-pin SOIC format (对比 OPA828ID)
  • Documented low-noise wideband operation (对比 OPA828ID)
  • Flexible single- and dual-supply operation (对比 OPA828ID)

设计说明

Place the supply bypass capacitors immediately adjacent to the V+ and V- pins and keep the supply current loop as compact as possible. For a high-frequency layout, route the amplifier output directly to the load or next-stage input rather than through a long unprotected trace. Keep the inverting-input and feedback components close to pins 2 and 6 so parasitic capacitance does not unexpectedly alter the closed-loop response. Use a continuous ground reference beneath the device where board density permits.

Use the 110 MHz gain-bandwidth figure as a loop-gain parameter rather than treating it as a guaranteed closed-loop bandwidth at every gain. Select the feedback resistors to limit parasitic capacitance and ensure the complete source, feedback, and load network remains stable. If the OPA830ID drives cable, ADC input capacitance, or a long trace, check output loading and overshoot before production. This is particularly important because the low-power wideband topology can make PCB parasitics more significant than they are in a slower precision amplifier.

Do not assume the full negative rail is always a valid input voltage, and do not design output signals to exceed the stated 25 mV supply-rail margin. The usable input and output ranges depend on supply voltage and operating conditions, so verify the relevant limits in the OPA830 datasheet. Also avoid using the gain-bandwidth product alone to estimate settling time or output bandwidth. A gain of two or greater requires particular attention to feedback-network impedance, noise gain, and capacitive-load stability.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals statement is stated for the exact OPA830ID ordering variant. AEC-Q100 is not applicable to this general-purpose amplifier package.

相关搜索

OPA830ID datasheet OPA830ID datasheet pdf OPA830ID pinout OPA830ID specifications Texas Instruments OPA830ID OPA830ID 110MHz amplifier OPA830ID SOIC-8 OPA830ID replacement OPA830ID equivalent OPA830ID vs OPA828ID OPA830ID price OPA830ID stock OPA830ID application circuit OPA830ID signal buffering

相关元器件 & 术语

Texas Instruments OPA830ID OPA830 OPA828ID OPA832 operational amplifier voltage-feedback amplifier single-supply amplifier wideband amplifier low-power amplifier fixed-gain line driver gain-bandwidth product input voltage noise density input common-mode range output swing complementary common-emitter output stage 8-pin SOIC SOIC family surface-mount technology semiconductor data acquisition communications signal conditioning instrumentation analog signal chain
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情