PCA9515ADG4 - Dual I2C Buffer, 400kHz | Texas Instruments
MPN: PCA9515ADG4 ✓ فعالPCA9515ADG4 جائزہ
An I2C repeater is a type of bus buffer that regenerates or isolates a bidirectional bus segment. In the broader hierarchy, it is an interface IC, a bus-management IC, and a semiconductor. Unlike a unidirectional logic buffer, each PCA9515ADG4 channel supports signal flow in both directions, allowing the same two pins to participate in an I2C transaction. This makes the device useful when bus capacitance, loading, voltage differences, or physical distance prevents one controller from driving the complete bus reliably.
The PCA9515ADG4 provides two bidirectional channels, a 400 kHz operating-rate designation, 5.5 V-tolerant I2C I/O, and a 5.5 V-tolerant enable input. Its open-drain I/O architecture is compatible with the wired-AND behavior required by I2C and SMBus. The specified propagation delay is 113 ns, while input capacitance is 7 pF, characteristics that are important when budgeting capacitive loading and propagation delay across the repeated bus segment.
The device requires a supply voltage between 2.3 V and 3.6 V. A typical implementation connects the buffer between a bus-master side and a remote peripheral side, with pull-up resistors placed separately on each side of the repeater. The enable input can hold the buffers in a high-impedance state when the downstream segment must be isolated. The measured 500 µA supply current supports low-power embedded systems while keeping the repeater available for continuous bus operation.
Typical uses include extending an I2C sensor bus, isolating a controller from noisy peripherals, separating high-capacitance bus sections, and supporting SMBus-compatible equipment. It is particularly useful when the same PCB contains several addressable sensors, EEPROMs, analog converters, or power-monitoring components. Industrial temperature-grade availability and the compact SOIC-8 footprint make it practical for embedded control and instrumentation systems.
For reliable operation, use pull-up resistors on each isolated bus segment and verify that total capacitance, sink-current loading, and timing remain within the limits of every connected device. Keep the repeater-enable net defined so that power-up cannot accidentally leave a downstream segment floating or partially enabled. Check signal polarity and bus direction at the system level because both channels are bidirectional and operate through open-drain pull-ups.
This page combines the PCA9515ADG4 electrical characteristics with package information, application guidance, design considerations, and a verified same-package replacement reference. It is intended to help engineers select the correct bus repeater, plan its board layout, and distinguish a true pin-compatible substitute from parts that require PCB changes.
کے لیے ڈراپ اِن متبادل PCA9515ADG4 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں PCA9515ADG4 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Enable Input, Number of Channels, Package.
PCA9515ADR
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PCA9515ADG4 تفصیلات
| Product Type | Dual bidirectional I2C bus and SMBus repeater |
| Number of Channels | 2 channels |
| Supply Voltage Range | 2.3 V to 3.6 V |
| Maximum Bus Frequency | 400 kHz |
| Propagation Delay | 113 ns |
| اِن پٹ کیپیسیٹنس | 7 pF |
| سپلائی کرنٹ | 500 µA |
| I/O Architecture | Bidirectional open-drain |
| Enable Input | Active-high repeater enable |
| I2C I/O Voltage Tolerance | 5.5 V tolerant |
| Enable Input Voltage Tolerance | 5.5 V tolerant |
| Bus Compatibility | I2C and SMBus |
| پیکیج | 8-SOIC (0.154 inch, 3.90 mm width) |
| ماؤنٹنگ ٹائپ | Surface mount |
| Temperature Grade | Industrial grade |
PCA9515ADG4 8-soic (0.154 inch, 3.90 mm width) پن کنفیگریشن گائیڈ
PCA9515ADG4 (8-soic (0.154 inch, 3.90 mm width) پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں PCA9515ADG4.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
PCA9515ADG4 کے لیے موزوں ہے 6 ایپلیکیشنs: Extended I2C Sensor Bus, SMBus Equipment Segmentation, Isolated Industrial Control Bus, Precision Data Acquisition Bus, Battery-Powered Sensor Node, Power and Current Monitoring System.
Extended I2C Sensor Bus
The PCA9515ADG4 fits an extended I2C sensor bus because its two bidirectional channels can divide a high-capacitance network into separately pulled-up sections. With a 2.3 V to 3.6 V operating range and a 400 kHz rating, it preserves the standard I2C topology while limiting the load seen by the controller. Its 113 ns propagation delay and 7 pF input capacitance should be included in the bus timing and capacitance budget, especially when several addressable sensors share the repeated segment.
تجویز کردہ
SMBus Equipment Segmentation
The PCA9515ADG4 is appropriate for segmenting an SMBus-compatible control network when passive or active devices create excessive loading. Its two open-drain bidirectional channels preserve the wired-AND signaling used by SMBus, while the active-high enable control allows a downstream segment to be isolated when required. The 400 kHz bus rating supports standard-mode and fast-mode operation, and the 2.3 V to 3.6 V supply range fits common embedded and industrial control voltages.
تجویز کردہ
Isolated Industrial Control Bus
The PCA9515ADG4 can separate a controller from a group of industrial peripherals when board layout, connector routing, or ground-related loading makes a single large I2C network impractical. Each open-drain channel is bidirectional, so data and acknowledge signals travel naturally in both directions. The active-high enable input provides deterministic segment control, while the 5.5 V-tolerant I2C and enable inputs provide additional interface margin when connected to compatible industrial peripherals.
تجویز کردہ
Precision Data Acquisition Bus
The PCA9515ADG4 can organize precision converters and sensors on a segmented I2C bus without changing the host protocol. Its 400 kHz capability accommodates the intended bus rate, while the 113 ns propagation delay and 7 pF input capacitance provide concrete values for timing and loading calculations. Place the repeater between the controller and the acquisition section, provide independent pull-ups on both segments, and verify that converter address pins, sample timing, and required data rates remain unaffected.
تجویز کردہ
Battery-Powered Sensor Node
The PCA9515ADG4 suits a battery-powered sensor node where bus loading and standby consumption influence the power budget. Its specified supply current of 500 µA and 2.3 V to 3.6 V operating range align with common embedded supply systems. The active-high enable input can disable the repeated segment during inactive periods, although the external pull-up network and attached devices should also be evaluated for their own standby leakage and rail behavior.
تجویز کردہ
Power and Current Monitoring System
The PCA9515ADG4 can isolate a group of power-monitoring and current-sensing peripherals from a main control bus. The two bidirectional channels support separate repeated paths where needed, and the active-high enable permits deliberate bus-segment control. A 400 kHz rating provides ample margin for supervisory data traffic, while the 113 ns delay, 7 pF input capacitance, and 2.3 V to 3.6 V supply range make the repeater suitable for deterministic embedded monitoring networks.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا PCA9515ADG4 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | PCA9515ADR |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | 8-SOIC | 8-SOIC |
| Product Type | Dual bidirectional I2C/SMBus repeater | Dual bidirectional I2C/SMBus repeater |
| Channel Count | 2 channels | 2 channels |
| Operating Supply Voltage | 2.3 V to 3.6 V | 2.3 V to 3.6 V |
| Maximum Bus Frequency | 400 kHz | 400 kHz |
| I/O Architecture | Bidirectional open-drain | Bidirectional open-drain |
اہم امتیازی خصوصیات
- Same-package 8-SOIC replacement path (بمقابلہPCA9515ADR)
- Bidirectional bus handling in one compact IC (بمقابلہTCA9517)
- Fast-mode I2C operation (بمقابلہPCA9515ADR)
ڈیزائن نوٹس
Place the PCA9515ADG4 at the physical boundary between the controller-side and peripheral-side I2C networks. Route each bidirectional channel as a continuous signal path between its corresponding pins, and keep the two sides electrically separated until they reach the repeater. The 7 pF input capacitance contributes to each segment's effective loading, so avoid unnecessary stubs and keep the repeated devices away from long connector or cable branches.
Use separate pull-up resistors on the two sides of the repeater and calculate each value from that segment's capacitance, sink-current requirement, and target 400 kHz rise time. Do not assume that the pull-ups can be shared across the buffered boundary. The device supply must remain between 2.3 V and 3.6 V, while the 5.5 V tolerance applies to the specified I2C I/O and enable inputs rather than creating permission to exceed the supply rating.
Do not substitute a narrow-body package option such as PCA9515APWRG4 into an 8-SOIC footprint, and do not treat the TCA9517 as a drop-in part because its separate supply pins require board changes. Confirm the exact pin assignments and package drawing in the manufacturer datasheet before production release. Also ensure that the enable signal has a defined state during reset and power-up so the downstream bus segment cannot be left partially enabled.
تعمیل کی معلومات
The PCA9515ADG4 is described as industrial grade. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer product documentation.