PCA9555DW - 16-Bit I/O Expander, 2.3-5.5V | TI
MPN: PCA9555DW ✓ فعالPCA9555DW جائزہ
An I/O expander is an interface IC that translates serial I2C or SMBus commands into parallel digital input or output signals. In the signal-chain hierarchy, it sits between a microcontroller or embedded processor and external panel buttons, LEDs, relays, sensors, or other digital peripherals. The PCA9555 combines addressable input and output ports with configurable polarity and an interrupt mechanism, reducing host pin count while preserving a simple two-wire control path.
Key features include 16 configurable I/O lines, active-low open-drain interrupt output, weak pull-up configuration registers, and compatibility with both I2C and SMBus systems. Each port can be configured independently as input or output through the device registers. Input polarity inversion and output drive behavior can be programmed, allowing the same device to support active-low buttons, indicator circuits, and other digital interfaces.
The PCA9555 is controlled through a serial interface using address-select pins and command registers. This makes firmware configuration straightforward when the host already supports I2C. The 400kHz operating capability helps reduce control-loop time when multiple expander devices are present or when the system needs responsive input polling. The device is intended for systems where distributed GPIO expansion is preferable to expanding the host package.
Typical applications include industrial control panels, keypad and button interfaces, LED indication, appliance controls, instrumentation, and embedded systems requiring more GPIO than the host microcontroller provides. The 2.3V to 5.5V supply range supports both low-voltage and conventional 5V digital systems. The 24-pin SOIC package also makes the device suitable for through-hole assembly and conventional PCB layouts.
When designing around the PCA9555, account for the I2C bus pull-up requirement, correct address selection, and the electrical limits of each output. The interrupt pin should be configured with an appropriate pull-up because it is open-drain and active low. Firmware should also define startup states and port directions before external circuitry becomes active. This page summarizes the verified device identity, package, operating range, interface features, and design implications available for PCA9555DW selection.
This information distinguishes the PCA9555DW from generic 8-bit expanders by combining a 16-bit parallel interface, configurable weak pull-ups, polarity control, and interrupt support in a 2.3V to 5.5V SOIC device.
کے لیے ڈراپ اِن متبادل PCA9555DW — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں PCA9555DW (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Interrupt Output, Package, Configuration Registers.
PCA9555DWR
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PCA9555D,112
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
TCA9555PWR
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PCA9535DWR
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PCF8575DWR
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PCA9555DW تفصیلات
| Device Type | 16-bit I2C/SMBus I/O expander |
| Supply Voltage Range | 2.3 V to 5.5 V |
| I/O Port Count | 16 bits |
| Port Organization | 2 x 8-bit ports |
| Bus Interface | I2C/SMBus |
| Maximum Bus Frequency | 400 kHz |
| Interrupt Output | Active-low, open-drain |
| Weak Pull-up Registers | Configurable |
| Configuration Registers | Input/output, polarity and port configuration |
| Output Drive | Push-pull outputs |
| آپریٹنگ درجہ حرارت رینج | -40°C to +85°C |
| پیکیج | 24-pin SOIC (DW) |
| Package Type | SOIC |
| پن کی تعداد | 24 pins |
| ماؤنٹنگ ٹائپ | Surface mount |
| Low Standby Current | 1 µA maximum |
PCA9555DW soic پن کنفیگریشن گائیڈ
PCA9555DW (soic پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں PCA9555DW.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
PCA9555DW کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Control Panel, Embedded Keypad Interface, LED Status and Indicator Control, Appliance and Household Control, Instrumentation and Measurement Front Panel, Communication and Network Equipment.
Industrial Control Panel
The PCA9555DW is suitable for control panels where a controller needs to monitor many pushbuttons and drive indicators over a shared bus. Its 16-bit organization allows two 8-bit groups to be assigned to inputs and outputs, while the 2.3V to 5.5V range accommodates common industrial logic levels. The active-low open-drain interrupt can notify the host when a panel event requires service. Firmware should define input polarity, debounce behavior, and startup states before enabling external loads.
تجویز کردہ
Embedded Keypad Interface
Use the PCA9555DW to connect keypad or switch matrices to a microcontroller without consuming dedicated GPIO pins. Sixteen I/O lines provide enough parallel signals for compact keypad scanning, status keys, or configuration switches, while the serial host interface reduces wiring complexity. Configure the required lines as inputs and use the interrupt to report state changes efficiently. Check the external switch voltage levels and account for scan timing in the host firmware.
تجویز کردہ
LED Status and Indicator Control
The PCA9555DW can drive grouped LED status indicators when the host must preserve package pins for higher-speed or mixed-signal functions. Two programmable 8-bit ports allow firmware to update display status in parallel while keeping the physical interface compact. The verified 2.3V to 5.5V operating range supports common logic systems, but LED current, polarity, and series resistance must be designed for the chosen supply. The interrupt output is less central in a continuously refreshed indicator application.
تجویز کردہ
Appliance and Household Control
The PCA9555DW can expand a small appliance controller to handle door switches, mode buttons, relays, and status lamps through one I2C/SMBus connection. The 16 I/O lines allow a compact controller to separate input sensing from output control, while configurable polarity helps match active-low switch networks. The device should be placed where its 2.3V to 5.5V supply range matches the logic system. Firmware should initialize port directions and output states before enabling connected actuators.
تجویز کردہ
Instrumentation and Measurement Front Panel
The PCA9555DW is useful in instrumentation front panels where range selectors, mode buttons, alarm inputs, and indicator outputs must be connected to a controller. Its two 8-bit ports provide organized grouping for input sensing and output control, and the interrupt line can signal a changed front-panel state without continuous host polling. The 400kHz interface capability helps support timely updates when several controls are managed by the host. Verify logic thresholds and protection requirements for external equipment.
تجویز کردہ
Communication and Network Equipment
The PCA9555DW can add local status, configuration, and alarm I/O to a communication module whose main processor has insufficient package pins. The serial bus keeps the expansion wiring compact, and the active-low interrupt allows a host to respond to external events. In network-oriented equipment, isolate or protect external lines according to the enclosure and electromagnetic environment; the expander itself does not provide surge protection. Confirm the system voltage and ensure that all connected signals remain within the verified operating limits.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا PCA9555DW — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | PCA9555DWR | PCA9555D,112 | TCA9555PWR | PCA9535DWR | PCF8575DWR |
|---|---|---|---|---|---|---|
| Package | 24-pin SOIC (DW) | 24-pin SOIC (DW) | 24-pin SOIC (DW) | 24-pin SOIC (PW) | 24-pin SOIC (D) | 24-pin SOIC (D) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
اہم امتیازی خصوصیات
- 16-bit expansion in a single device (بمقابلہPCF8575DWR)
- Programmable weak pull-ups and polarity control (بمقابلہPCA9535DWR)
- Broad 2.3V to 5.5V supply range (بمقابلہTCA9555PWR)
- Active-low open-drain interrupt output (بمقابلہPCA9555DWR)
ڈیزائن نوٹس
The verified PCA9555DW operating range is 2.3V to 5.5V, so the supply must remain within that interval during startup, normal operation, and shutdown. Confirm the logic levels of every connected peripheral and select I2C pull-ups for the actual bus voltage and capacitance. The verified low-standby-current specification is 1 µA maximum, but total system consumption also includes enabled ports, pull-ups, and connected devices.
Place the device close to the connector or controlled peripheral group and keep the I2C traces short and continuous. Provide the required bus pull-ups at a location consistent with the system’s I2C topology, and route the interrupt trace away from noisy switching nodes where practical. Because the interrupt output is active-low and open-drain, use a suitable pull-up and do not add a push-pull driver to that signal.
Initialize port direction, polarity, and output latch values before enabling connected loads; otherwise an external device may see an unintended startup state. Do not assume that a same-package comparison part has the same register map or address behavior. Review the exact manufacturer pinout, device address configuration, electrical limits, and firmware sequence before substituting PCA9555DW-family candidates.
Treat the I2C lines as a shared bus with pull-up-defined high levels. Check rise time against the bus capacitance and the host timing budget at the selected 400kHz operating point. If several expanders or long routes are present, measure the bus rather than relying only on nominal component values. Configure the interrupt mask and polarity in firmware to avoid unnecessary wakeups and false event handling.
تعمیل کی معلومات
The supplied verified data confirms the Texas Instruments product, electrical operating range, interface features, package, and temperature range, but it does not provide compliance-status evidence. No RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals claim is inferred.
