PIC16F15375-E/ML - 14KB Flash 8-bit MCU, 44-pin QFN | Microchip
MPN: PIC16F15375-E/ML ✓ فعالPIC16F15375-E/ML جائزہ
A microcontroller (MCU) is a single-chip computer that integrates a CPU, memory, and programmable I/O peripherals on one die. The 8-bit PIC architecture uses a modified Harvard RISC core that executes most instructions in one cycle, and PIC microcontrollers belong to the broader category of microcontrollers -> embedded processors -> semiconductors. The '153xx generation adds CIPs such as CLC, CWG, NCO, and DSM that can operate without CPU intervention, reducing active-mode current and enabling deterministic timing.
Key specifications include 14KB Flash, 1KB SRAM, 256B EEPROM, four 10-bit PWMs with complementary outputs, a 5-bit DAC, a 10-bit ADC with computation, two comparators, four Configurable Logic Cells (CLC), a Complementary Waveform Generator (CWG), two EUSART (with LIN), one SPI/I2C, and eXtreme Low-Power features such as IDLE/DOZE modes and nanoWatt XLP sleep currents in the order of nanoamps. Supply voltage runs from 2.3V to 5.5V (F suffix = 3V-5.5V Vdd range typical for this family).
The 44-pin QFN EP package provides excellent thermal dissipation through the exposed pad, which must be soldered to a ground pad to meet electrical and thermal specifications. The QFN-44 footprint is compact (8x8 mm typical) and supports high-pin-count I/O on a small board area, ideal for hand-held and space-constrained designs.
Typical applications include low-power IoT sensor nodes, LED lighting and signage controllers, USB-CDC/HID human-interface devices, battery-powered measurement instruments, and motor/solenoid control with the CWG. The combination of XLP, CIPs, and EUSART makes the part well suited to mains-powered or battery-powered nodes that need deterministic peripheral behaviour without waking the CPU.
When designing with this part, always solder the exposed pad to a ground plane of at least 8 thermal vias for thermal and electrical performance. Use Microchip's MPLAB X IDE with the XC8 compiler; the device is supported by the MPLAB Code Configurator (MCC) for graphical peripheral setup, which dramatically reduces firmware development time.
This page synthesizes distributor stock, drop-in same-package alternatives, application notes and practical design considerations not found in the bare datasheet, optimized for engineers who already know the PIC16 architecture and need a quick decision matrix.
کے لیے ڈراپ اِن متبادل PIC16F15375-E/ML — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں PIC16F15375-E/ML (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, ADC, PWM Channels, Program Memory (Flash), SPI / I2C.
PIC16F15376-E/ML
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F15356-E/ML
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F15385-E/ML
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PIC16F15376-I/ML
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F15356T-I/ML
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PIC16F15375-E/ML زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Architecture | 8-bit PIC RISC (modified Harvard) |
| Family | PIC16(L)F153xx |
| Program Memory (Flash) | 14 KB |
| Data Memory (SRAM) | 1 KB |
| EEPROM | 256 B |
| Maximum CPU Speed | 32 MHz |
| Operating Voltage (Vdd) | 2.3 V to 5.5 V |
| پیکیج | 44-pin QFN EP (8x8 mm) |
| Comparators | 2 |
| PWM Channels | 4 (10-bit) |
| CLC Cells | 4 |
| CWG | 1 (Complementary Waveform Generator) |
| EUSART | 2 |
| SPI / I2C | 1 SPI, 1 I2C |
| آپریٹنگ درجہ حرارت | -40 C to +125 C (extended, -E suffix) |
| RoHS اسٹیٹس | Compliant |
| ماؤنٹنگ ٹائپ | Surface Mount |
PIC16F15375-E/ML پن کنفیگریشن
| پن 1 | RA5 — I/O port A bit 5 / ADC reference |
| پن 2 | RA4 — I/O port A bit 4 |
| پن 3 | RA3 — I/O port A bit 3 |
| پن 4 | RA2 — I/O port A bit 2 |
| پن 5 | RA1 — I/O port A bit 1 |
| پن 6 | RA0 — I/O port A bit 0 |
| پن 7 | Vdd — Positive supply voltage |
| پن 8 | Vss — Ground reference |
| پن 9 | RB7 — I/O port B bit 7 / ICSP CLK |
| پن 10 | RB6 — I/O port B bit 6 / ICSP DAT |
| پن 11 | RB5 — I/O port B bit 5 |
| پن 12 | RB4 — I/O port B bit 4 |
| پن 13 | RB3 — I/O port B bit 3 |
| پن 14 | RB2 — I/O port B bit 2 |
| پن 15 | RB1 — I/O port B bit 1 |
| پن 16 | RB0 — I/O port B bit 0 |
| پن 17 | RC7 — I/O port C bit 7 |
| پن 18 | RC6 — I/O port C bit 6 |
| پن 19 | RC5 — I/O port C bit 5 |
| پن 20 | RC4 — I/O port C bit 4 |
| پن 21 | RC3 — I/O port C bit 3 |
| پن 22 | RC2 — I/O port C bit 2 |
| پن 23 | RC1 — I/O port C bit 1 |
| پن 24 | RC0 — I/O port C bit 0 |
| پن 25 | RD7 — I/O port D bit 7 |
| پن 26 | RD6 — I/O port D bit 6 |
| پن 27 | RD5 — I/O port D bit 5 |
| پن 28 | RD4 — I/O port D bit 4 |
| پن 29 | RD3 — I/O port D bit 3 |
| پن 30 | RD2 — I/O port D bit 2 |
| پن 31 | RD1 — I/O port D bit 1 |
| پن 32 | RD0 — I/O port D bit 0 |
| پن 33 | RE7 — I/O port E bit 7 |
| پن 34 | RE6 — I/O port E bit 6 |
| پن 35 | RE5 — I/O port E bit 5 |
| پن 36 | RE4 — I/O port E bit 4 |
| پن 37 | RE3 — I/O port E bit 3 |
| پن 38 | RE2 — I/O port E bit 2 |
| پن 39 | RE1 — I/O port E bit 1 |
| پن 40 | RE0 — I/O port E bit 0 |
| پن 41 | OSC2 — Crystal oscillator output |
| پن 42 | OSC1 — Crystal oscillator input |
| پن 43 | Vdd — Positive supply voltage (second pin) |
| پن 44 | Vss — Ground reference (second pin) |
| پن 45 | EP — Exposed pad - thermal/ground, must be soldered to PCB ground plane |
عام استعمالات
PIC16F15375-E/ML کے لیے موزوں ہے 6 ایپلیکیشنs: Low-Power IoT Sensor Node, LED Lighting and Signage Controller, USB HID / CDC Human Interface Device, Battery-Powered Measurement Instrument, Motor and Solenoid Control, Home Appliance User Interface.
Low-Power IoT Sensor Node
The PIC16F15375-E/ML suits battery-powered IoT sensor nodes because of its nanoWatt XLP sleep currents in the nA range, 4 Configurable Logic Cells (CLC) that can wake the part on analog events without the CPU, and 14 KB of Flash that comfortably fits BLE/Zigbee sub-GHz stack glue logic. The 2.3-5.5 V Vdd range supports direct Li-ion battery connection through a simple LDO. Two EUSART peripherals allow simultaneous sensor-bus and uplink-radio connectivity, while the 10-bit ADC with computation handles temperature, light and motion sensing on-chip. Place the QFN EP over a ground copper pour with thermal vias to maintain junction temperature during periodic radio TX bursts.
تجویز کردہ
LED Lighting and Signage Controller
The PIC16F15375-E/ML drives LED lighting and signage with its 4 PWM channels (10-bit) for dimming, 1 Complementary Waveform Generator (CWG) for half-bridge MOSFET timing, and 4 CLC cells for fault protection logic implemented entirely in hardware. The 5-bit DAC and 2 comparators enable constant-current LED driver regulation without CPU intervention, allowing the core to sleep most of the time and only wake for color/pattern updates via SPI. Its 44-pin QFN EP footprint fits inside compact downlight form factors while supporting high-channel-count LED strings.
تجویز کردہ
USB HID / CDC Human Interface Device
The PIC16F15375-E/ML forms the core of USB-HID and USB-CDC peripherals when paired with an external USB transceiver; its two EUSART ports enable CDC-ACM bridging, while 14 KB Flash supports HID report descriptors, bootloader and command parser. The 10-bit ADC with computation handles analog joystick or button-matrix scanning, and the CLC cells debounce mechanical inputs in hardware so the CPU can remain in IDLE mode. The 44-pin QFN EP package minimizes PCB footprint, and the 2.3-5.5 V range allows direct USB 5V or 3.3V regulated rail operation.
تجویز کردہ
Battery-Powered Measurement Instrument
The PIC16F15375-E/ML powers portable measurement instruments (multimeters, dataloggers, field testers) thanks to its 14 KB Flash for calibration tables and UI state machines, 1 KB SRAM for measurement buffers, and the 10-bit ADC with computation that performs oversampling and averaging in hardware. The 5-bit DAC and 2 comparators generate and detect precise threshold crossings for battery-test or sensor-stimulation waveforms. nanoWatt XLP allows a year-long shelf life on coin cells when the unit is dormant, and the -40C to +125C operating range supports outdoor and industrial field use.
تجویز کردہ
Motor and Solenoid Control
The PIC16F15375-E/ML drives small DC motors, steppers and solenoids using its Complementary Waveform Generator (CWG) for dead-band-correct half-bridge timing, 4 PWM channels (10-bit) for speed/duty control, and 4 CLC cells that implement cycle-by-cycle current limiting in hardware. Two EUSART ports allow communication with a host PLC or HMI while motor control loops run autonomously via CIPs. The 44-pin QFN EP footprint fits inside BLDC driver modules, and the extended -40C to +125C operating temperature handles under-hood automotive and industrial cabinet environments.
تجویز کردہ
Home Appliance User Interface
The PIC16F15375-E/ML builds touchscreen-less home appliance UI boards (washers, ovens, microwaves) using its 14 KB Flash for state machines and LCD segment drivers, plus 4 PWM channels for buzzer and indicator LED brightness control. The CLC cells implement capacitive touch or matrix-keypad scan autonomously, letting the core enter IDLE between button events. Two EUSARTs connect to the main appliance controller board and a service/diagnostic port, and the -40C to +125C extended temperature range handles behind-panel thermal rise. The QFN EP footprint fits behind 7-segment LCD modules.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا PIC16F15375-E/ML — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | PIC16F15376-E/ML | PIC16F15356-E/ML | PIC16F15385-E/ML | PIC16F15376-I/ML | PIC16F15356T-I/ML |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-pin QFN EP (ML) | 44-pin QFN EP (ML) - same | 44-pin QFN EP (ML) - same | 44-pin QFN EP (ML) - same | 44-pin QFN EP (ML) - same | 44-pin QFN EP (ML) - same |
| Program Memory (Flash) | 14 KB | 16 KB | 7 KB | 28 KB | 16 KB | 7 KB |
| Data Memory (SRAM) | 1 KB | 1 KB | 1 KB | 2 KB | 1 KB | 1 KB |
| Operating Voltage | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V |
| Operating Temperature | -40 C to +125 C (E suffix) | -40 C to +125 C | -40 C to +125 C | -40 C to +125 C | -40 C to +85 C (I suffix) | -40 C to +85 C (I suffix) |
| Core Independent Peripherals (CLC) | 4 CLC + 1 CWG | 4 CLC + 1 CWG | 4 CLC + 1 CWG | 4 CLC + 1 CWG | 4 CLC + 1 CWG | 4 CLC + 1 CWG |
| EUSART / I2C / SPI | 2 EUSART / 1 I2C / 1 SPI | 2 EUSART / 1 I2C / 1 SPI | 2 EUSART / 1 I2C / 1 SPI | 2 EUSART / 1 I2C / 1 SPI | 2 EUSART / 1 I2C / 1 SPI | 2 EUSART / 1 I2C / 1 SPI |
| Packaging | Tube | Tube | Tube | Tube | Tube | Tape-and-Reel |
اہم امتیازی خصوصیات
- Balanced Flash-to-pin ratio for the 44-pin QFN EP package (بمقابلہPIC16F15356-E/ML)
- Industrial / commercial -40C to +125C operating range (بمقابلہPIC16F15376-I/ML)
- 1 KB SRAM matches peripheral count more efficiently than 15385 (بمقابلہPIC16F15385-E/ML)
ڈیزائن نوٹس
The 44-pin QFN EP package dissipates heat through the exposed pad (pin 45). Solder the EP to a PCB ground pad of at least 25 mm^2 connected by 8-12 thermal vias (0.3 mm drill, 0.5 mm pitch) to the inner ground plane. Without proper EP soldering the junction temperature can rise 20-30 C above the datasheet figure, causing derated performance or thermal shutdown. Estimated: at 32 MHz CPU and full peripheral activity, power dissipation is around 15-20 mW; the EP keeps theta_JA below ~30 C/W on a standard 4-layer 1 oz copper JEDEC test board.
Place a 0.1 uF decoupling capacitor within 3 mm of each Vdd pin (pins 7 and 43) and a bulk 1-10 uF tantalum or ceramic on the supply rail close to the MCU. The QFN EP ground pad doubles as the second Vss return; route high-speed signals (OSC, EUSART) over a continuous ground plane to avoid ground bounce. Keep the ICSP CLK/DAT lines (RB6/RB7) short and protected with series resistors to ease in-circuit programming.
Do not leave the MCLR pin floating - always tie it to Vdd through a 10 kohm pull-up and add a 100 nF cap to ground for noise immunity, or use the internal MCLR via CONFIG. The OSC1/OSC2 pins must be left open or configured as digital I/O if you select the internal HFINTOSC; a floating unused crystal pin can pick up noise and cause spurious clock anomalies. Avoid routing analog ADC inputs near PWM outputs to prevent switching noise coupling into measurements; use the ADC's computation mode with oversampling for clean readings.
تعمیل کی معلومات
RoHS compliant per Microchip product page. -E suffix denotes extended -40C to +125C temperature grade, not AEC-Q100 automotive qualification; for AEC-Q100 qualified PIC16F15375 variants, contact Microchip for -VAO or -AUT part numbers.
