Texas Instruments

SN74HC126N - 4-Channel 3-State CMOS Buffer | Texas Instruments

MPN: SN74HC126N ✓ فعال
2 V to 6 V Vdss 14-pin through-hole DIP Package
MOQ: 1 |

SN74HC126N جائزہ

The Texas Instruments SN74HC126N is a four-channel, non-inverting CMOS bus buffer with individually controlled 3-state outputs, a 2 V to 6 V operating supply range, and a 14-pin DIP package. Each buffer channel provides a high-impedance output state for shared-bus and bidirectional-interface isolation, while the non-inverting input stage preserves signal polarity. The device is intended for 74HC-compatible systems operating from 2 V to 6 V.

A bus buffer is a digital logic device that strengthens a signal so it can reliably drive another logic stage or a shared bus. The 74HC family belongs to the high-speed CMOS logic hierarchy, where low static power, broad supply-voltage operation, and CMOS-compatible noise levels support portable, industrial, and embedded designs. The SN74HC126N adds a controlled high-impedance state to each output, allowing multiple drivers to share one bus without contention when their output-enable inputs are inactive.

The primary feature is independent tri-state control on all four channels. When an output-enable input is at its active level, the corresponding buffer passes its non-inverting input to the output. When the enable input is inactive, that output enters a high-impedance state and stops driving the connected net. This makes the SN74HC126N useful for bus isolation, bidirectional transceiver interfacing, test-point multiplexing, and systems that must park outputs safely during reset or power transitions.

The 2 V to 6 V supply range allows operation from low-voltage systems such as 2.5 V and 3.3 V rails through conventional 5 V logic. Because the outputs can enter a high-impedance state, external pull-up or pull-down resistors normally establish the state of a bus during disabled periods. The 14-pin through-hole package supports conventional DIP assembly, prototyping, and repair rather than high-density surface-mount layouts.

Typical uses include computer and peripheral bus buffering, memory-module interface isolation, industrial control boards, and shared data buses where multiple sources must be disconnected electrically. In each case, the enable controller must guarantee that only one buffer drives a net at a time. The high-impedance state should also be considered during power-up, reset, and hot-plug transitions to prevent undefined drive currents.

A practical design point is to control each output-enable input with a defined logic level and account for bus capacitance, pull resistor strength, and the switching limits listed in the manufacturer datasheet. The datasheet also permits driving a high-impedance CMOS input, but the total capacitive load must remain within the specified maximum. For new compact designs, the surface-mount form of the SN74HC126 family is generally preferred.

This page combines the manufacturer product information, distributor availability data, cross-reference research, pin-level implementation guidance, and application-oriented engineering notes. It is intended to help designers confirm footprint compatibility, output-enable behavior, supply requirements, and bus loading before committing the part to a new board.

کے لیے ڈراپ اِن متبادل SN74HC126N — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

CD74HC126E

✅ ڈراپ-اِن
📦 14-pin DIP
Same four-channel active-high 3-state buffer function and 14-pin DIP footprint; supply, timing, and drive ratings require datasheet comparison

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

MC74HC126N

✅ ڈراپ-اِن
📦 14-pin DIP
Same four-channel active-high 3-state function in a 14-pin DIP package; propagation delay and output-current limits vary by manufacturer

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

74HC126N

✅ ڈراپ-اِن
📦 14-pin DIP
Same 74HC126 quad tri-state buffer configuration and 14-pin DIP outline; verify sourcing-specific timing and electrical limits

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

TC74HC126P

✅ ڈراپ-اِن
📦 14-pin DIP
Same four-channel 3-state CMOS buffer function with active-high enables in a 14-pin DIP package; switching specifications differ

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

HCF126M013

✅ ڈراپ-اِن
📦 14-pin DIP
Same four-channel active-high 3-state buffer architecture in a 14-pin DIP package; propagation delay and noise specifications vary

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

SN74HC126N زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

Number of Channels 4 channels
Operating Supply Voltage Range 2 V to 6 V
Logic Type Non-inverting
Output State 3-state, high-impedance output
Device Function Quadruple bus buffer / line driver
Elements per Channel 1 bit
آؤٹ پٹس کی تعداد 4 outputs
Number of Output Enables 4 independently controlled output enables
Output Enable Polarity Active high
Package Type 14-pin through-hole DIP
ماؤنٹنگ اسٹائل Through-hole
Logic Family 74HC CMOS

SN74HC126N پن کنفیگریشن

DIP-14 Package Pinout Diagram DIP-14 14-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 DIP-14
پن 1 1OE — Output enable for channel 1; high enables the output and low places it in a high-impedance state
پن 2 1A — Data input for channel 1
پن 3 1Y — Non-inverting output for channel 1
پن 4 2OE — Output enable for channel 2; high enables the output and low places it in a high-impedance state
پن 5 2A — Data input for channel 2
پن 6 2Y — Non-inverting output for channel 2
پن 7 GND — Ground reference
پن 8 3OE — Output enable for channel 3; high enables the output and low places it in a high-impedance state
پن 9 3A — Data input for channel 3
پن 10 3Y — Non-inverting output for channel 3
پن 11 4OE — Output enable for channel 4; high enables the output and low places it in a high-impedance state
پن 12 4A — Data input for channel 4
پن 13 4Y — Non-inverting output for channel 4
پن 14 VCC — Power supply input

عام استعمالات

SN74HC126N کے لیے موزوں ہے 6 ایپلیکیشنs: Shared Computer and Peripheral Buses, Memory and Peripheral Interface Isolation, Industrial Control and Automation Boards, Bidirectional Transceiver Interfaces, Test and Measurement Signal Multiplexing, Legacy Embedded System Retrofitting.

🖥️

Shared Computer and Peripheral Buses

The SN74HC126N fits shared-bus designs because each of its four non-inverting buffers can drive a logic net or disconnect electrically through an active-high output enable. Place one buffer between a source device and a bus segment when the source must be isolated during another module's access cycle. The 2 V to 6 V operating range supports 2.5 V, 3.3 V, and 5 V legacy systems, while the 3-state output prevents two enabled drivers from fighting over the same net. Confirm the connected bus capacitance and pull-resistor strength against the Texas Instruments switching-characteristics limits, and guarantee that only one driver is enabled at any time.

🔧

Memory and Peripheral Interface Isolation

The SN74HC126N is useful between memory or peripheral interfaces and a multi-source bus because its individual active-high enables can hold unused outputs in a high-impedance state. This prevents an unselected device from loading address, data, or control lines and allows several memory devices to share routing resources. The four independent channels can handle four directional or multiplexed signals without changing the source logic. Use pull-up or pull-down resistors where a disconnected line must remain at a valid CMOS level, and check the datasheet's maximum capacitive-load figure against long PCB traces and package interconnects.

🏭

Industrial Control and Automation Boards

The SN74HC126N supports industrial control boards that combine several CMOS logic sources on common data or command buses. Its 2 V to 6 V supply range is useful for mixed-voltage control systems operating at 3.3 V or 5 V, while the non-inverting buffers preserve existing logic polarity. The three-state outputs let a controller isolate a fieldbus interface, sensor-conditioning logic, or actuator-driver section during reset. Because industrial systems can have long wiring and noisy environments, keep the logic net short where possible, validate the bus capacitance, and rely on pull resistors to establish safe levels while outputs are disabled.

🌐

Bidirectional Transceiver Interfaces

The SN74HC126N can support bidirectional communication paths where a shared conductor must accommodate more than one possible driver. Separate the transmit and receive paths with individual SN74HC126N channels and assert only the enable associated with the active direction. The disabled channel presents a high impedance rather than driving the line, which is essential when the opposite side of the interface is transmitting. Pull resistors can bias the shared conductor during direction changes, and their values must balance bus rise time against load current. Verify timing against the system clock and confirm that no control overlap can enable both drivers simultaneously.

📟

Test and Measurement Signal Multiplexing

The SN74HC126N can isolate several sensed or generated logic signals in a test and measurement system so that one acquisition bus is not disturbed by every connected circuit. Each active-high enable selects whether a particular source continues to drive the shared test point or becomes high impedance. This arrangement helps reduce contention and allows unused circuits to remain connected physically. Select pull values to preserve the intended idle level, keep probe and fixture capacitance within the allowed total load, and observe the specified switching limits when changing enable states rapidly.

🛠️

Legacy Embedded System Retrofitting

The SN74HC126N is a practical choice when maintaining a 5 V through-hole control board that needs stronger bus drive or removable drivers during troubleshooting. Its 14-pin DIP package fits conventional socketed or leaded layouts, and its 74HC-compatible 2 V to 6 V range allows operation within existing system tolerances. Four channels can isolate four contended nets without redesigning the surrounding logic. Before installation, confirm the exact pin assignment, verify that the board does not exceed the allowed capacitive load, and use a logic analyzer to confirm that output-enable transitions never create a moment with two drivers active.

What is the SN74HC126N?
The SN74HC126N is a four-channel, non-inverting 74HC CMOS bus buffer with independently controlled 3-state outputs in a 14-pin DIP package. According to the Texas Instruments product page, the device operates from 2 V to 6 V. Each channel can drive its output normally or place it in a high-impedance state, allowing multiple buffers to share a bus without active drive contention.
Where can I download the SN74HC126N datasheet PDF?
The official SN74HC126N datasheet PDF is available from the Texas Instruments literature link at https://www.ti.com/lit/ds/symlink/sn74hc126.pdf. It contains the recommended operating conditions, switching characteristics, output-enable truth table, logic diagrams, and maximum load-capacitance information. Use the manufacturer document as the controlling reference when checking timing and load limits for a specific supply voltage.
Where can I find the SN74HC126N pinout?
The SN74HC126N uses a standard 14-pin DIP arrangement with four data inputs, four non-inverting outputs, four active-high output-enable inputs, VCC, and GND. The pin-description table and logic diagram in the Texas Instruments SN74HC126 datasheet should be used when assigning PCB tracks. Pin 1 is identified by the package notch convention and the counter-clockwise numbering shown in the datasheet diagram.
How does the 3-state output on the SN74HC126N work?
Each SN74HC126N output is driven normally when its associated output-enable input is high and becomes high impedance when that enable input is low. The Texas Instruments SN74HC126 datasheet describes this behavior in its truth table and function table. A high-impedance output does not actively hold a logic level, so a pull-up or pull-down resistor is normally required when the bus must retain a defined state while disabled.
What is the difference between the SN74HC126 and SN74HC125?
The principal functional difference is the output-enable polarity: the SN74HC126 uses active-high output enables, while the SN74HC125 uses active-low output enables. Consequently, they are not automatically interchangeable on an existing board. The SN74HC126N also provides four non-inverting channels and a 3-state output, making it suitable where an enable-high control signal is preferred for bus-driver selection.
What is the best drop-in replacement for the SN74HC126N?
The CD74HC126E is a strong drop-in candidate because it implements the same four-channel 3-state buffer function with active-high output enables in a 14-pin DIP package. Its enable and data-pin assignments should still be checked against the specific manufacturer datasheet before production use. The Texas Instruments SN74HC126N remains preferable when device traceability, documentation, and a single manufacturer source are priorities.
Can the SN74HC126N replace the CD74HC126E?
The SN74HC126N can serve as a drop-in replacement for the CD74HC126E in a conventional 14-pin DIP design because both provide four non-inverting 3-state buffer channels with active-high output enables. Confirm the pin assignments, supply-voltage limits, timing, and output-drive requirements against both datasheets. This substitution is intended for existing through-hole layouts, not as a redesign instruction for surface-mount boards.
When should I choose the SN74HC126N instead of a generic 74HC126N?
Choose the SN74HC126N when you want a manufacturer-qualified 74HC126N with a consistent Texas Instruments ordering code, product documentation, and quality-program support. A generic 74HC126N may provide the same broad logic function and 14-pin DIP footprint, but its electrical limits, sourcing, and qualification documentation can differ by manufacturer. Verify operating conditions, timing, and enable behavior for any substitute rather than relying on the 74HC family name alone.
Is the SN74HC126N suitable for a shared bidirectional bus?
The SN74HC126N is suitable for a shared bus when the design guarantees that only one buffer is enabled at a time. Its four active-high output enables let a controller isolate individual drivers during arbitration, handoff, or reset. Because disabled outputs become high impedance rather than driving a defined level, the bus usually needs pull-up or pull-down resistors and must not be operated with multiple enabled outputs connected to the same net.
What supply voltage can the SN74HC126N use?
The Texas Instruments SN74HC126 product page specifies a 2 V to 6 V operating supply range. This supports 2.5 V, 3.3 V, and 5 V systems within their respective system tolerances. Use the manufacturer datasheet for the timing and output-current ratings that apply at the actual supply voltage, since those characteristics can change as the rail level changes.
Does the SN74HC126N require pull-up resistors on its outputs?
The SN74HC126N outputs require external pull resistors when a disabled output must hold a defined bus level. A disabled output enters a high impedance state and cannot actively drive the net high or low. Select pull-up or pull-down values using the bus capacitance, leakage current, speed requirements, and the drive strength of whichever buffer is enabled, as specified by the Texas Instruments datasheet.
How much capacitive load can the SN74HC126N drive?
The SN74HC126N can drive a high-impedance CMOS input while continuing to meet its specified operation limits, provided the total connected capacitance stays within the maximum load listed in the switching characteristics. Use the maximum-load entry in the Texas Instruments SN74HC126 datasheet for the selected supply voltage rather than estimating from board geometry. Long traces, stubs, connectors, and unterminated cables add capacitance that must be included in the budget.
Where can I buy the SN74HC126N and what is its price?
The SN74HC126N can be ordered through XAIPART using the Request a Quote form on this page. The form allows you to request current unit pricing, quantity breaks, stock confirmation, and lead time for the Texas Instruments 14-pin DIP part. Live commercial terms change by quantity, market condition, and supply, so request a quote for the specific quantities and delivery schedule required by your build.
Is the SN74HC126N in stock and what is the lead time?
Current SN74HC126N inventory and lead time should be confirmed through the Request a Quote form on this page. The Request a Quote workflow returns an availability and lead-time response for the requested quantity rather than relying on a static stock statement. Specify your required delivery date, annual usage, and packaging quantity so the quotation reflects a realistic supply commitment.
What are the key specifications of the SN74HC126N that engineers should know?
The key SN74HC126N specifications are four non-inverting channels, a 2 V to 6 V supply range, active-high independently controlled 3-state outputs, and a 14-pin DIP package. The device is a 74HC-series CMOS bus buffer intended to strengthen logic signals and isolate shared buses. Its outputs must not be used to hold a defined state while disabled; pull-up or pull-down resistors provide that function.
What can replace the SN74HC126N in a legacy through-hole design?
The CD74HC126E is a direct functional candidate for a legacy through-hole replacement because it offers the same four-channel 3-state buffer function and 14-pin DIP configuration. Other qualified 74HC126N and MC74HC126N sources may also fit the same functional footprint, but their data sheets control the final substitution decision. Confirm pinout, active-high enable polarity, supply range, timing, and load ratings before substituting any part.

کے لیے انجینئرنگ ریفرنس ڈیٹا SN74HC126N — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the SN74HC126N for new or maintained 74HC-compatible systems that require four non-inverting, independently disabled 3-state outputs in a 14-pin through-hole package. It is particularly suitable when one of several bus drivers must be disconnected safely and when the board operates on a 2 V, 3.3 V, or 5 V logic rail. Choose the CD74HC126E when it is the qualified source already used in the original design, provided its timing and electrical ratings meet the system requirements. Consider MC74HC126N, 74HC126N, TC74HC126P, or HCF126M013 for second-source supply, but compare the individual manufacturer datasheet rather than assuming identical 74HC-family timing. Do not substitute an active-low-enable 74HC125-type device without changing the control logic. For a compact new product, a surface-mount 74HC126 variant is normally preferable to the through-hole SN74HC126N.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ CD74HC126E MC74HC126N 74HC126N TC74HC126P HCF126M013
Package 14-pin DIP 14-pin DIP 14-pin DIP 14-pin DIP 14-pin DIP 14-pin DIP
Brand Texas Instruments Texas Instruments onsemi onsemi Toshiba STMicroelectronics
Number of Channels 4 4 4 4 4 4
Logic Type Non-inverting buffer Non-inverting buffer Non-inverting buffer Non-inverting buffer Non-inverting buffer Non-inverting buffer
Output State 3-state, high impedance when disabled 3-state, high impedance when disabled 3-state, high impedance when disabled 3-state, high impedance when disabled 3-state, high impedance when disabled 3-state, high impedance when disabled
Output Enable Polarity Active high Active high Active high Active high Active high Active high
Operating Supply Voltage Range 2 V to 6 V 2 V to 6 V 2 V to 6 V 2 V to 6 V 2 V to 6 V 2 V to 6 V

اہم امتیازی خصوصیات

  • Manufacturer-specific ordering code with a consolidated Texas Instruments product and quality documentation set (بمقابلہ74HC126N)
  • Direct functional equivalent with the same four-channel active-high 3-state architecture (بمقابلہCD74HC126E)
  • Broader supply-voltage operating window than many older bipolar bus-driver families (بمقابلہMC74HC126N)

ڈیزائن نوٹس

Never enable two SN74HC126N outputs that are connected to the same net. The device supports high-impedance bus sharing, but it does not resolve drive contention between simultaneously active outputs. Design the enable controller so that it produces a valid break-before-make sequence, and use pull-up or pull-down resistors to establish a defined state whenever all drivers are disabled.

The SN74HC126N operates from 2 V to 6 V, but the usable timing margin depends on the actual rail level and the total capacitive load. Include package parasitics, PCB trace capacitance, connector capacitance, and the input capacitance of the driven device when checking the switching limits. Avoid relying on a nominal 5 V rail to guarantee operation if the system can fall outside the component's rated supply range.

Keep disabled outputs from being treated as signal sources. A high-impedance output can float to an unintended level, so add a pull resistor whenever the downstream receiver must interpret a stable value during reset, disable, or bus handoff. Select the resistor with the bus rise-time requirement and the enabled driver's current capability in mind, and verify the resulting level against the receiving device's input thresholds.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The SN74HC126N is a general-purpose 74HC CMOS logic IC rather than an automotive-qualified device. Compliance attributes should be confirmed for the exact manufacturing site and orderable suffix through the manufacturer product documentation.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-14 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

sn74hc126n datasheet SN74HC126N datasheet pdf SN74HC126N pinout SN74HC126N equivalent SN74HC126N replacement SN74HC126N cross reference SN74HC126N vs CD74HC126E SN74HC126N price SN74HC126N stock Texas Instruments SN74HC126N SN74HC126N 3-state buffer SN74HC126N 14-pin DIP SN74HC126N shared bus application SN74HC126N output enable polarity

متعلقہ اجزاء اور اصطلاحات

Texas Instruments SN74HC126N CD74HC126E MC74HC126N 74HC126N TC74HC126P HCF126M013 74HC CMOS logic bus buffer line driver quadruple buffer 3-state output tri-state logic high-impedance output non-inverting buffer active-high output enable output-enable control 2 V to 6 V supply 14-pin DIP through-hole package shared bus bidirectional interface pull-up resistor pull-down resistor
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں