SN74HC126N - 4-Channel 3-State CMOS Buffer | Texas Instruments
MPN: SN74HC126N ✓ Hoạt độngSN74HC126N Tóm tắt
A bus buffer is a digital logic device that strengthens a signal so it can reliably drive another logic stage or a shared bus. The 74HC family belongs to the high-speed CMOS logic hierarchy, where low static power, broad supply-voltage operation, and CMOS-compatible noise levels support portable, industrial, and embedded designs. The SN74HC126N adds a controlled high-impedance state to each output, allowing multiple drivers to share one bus without contention when their output-enable inputs are inactive.
The primary feature is independent tri-state control on all four channels. When an output-enable input is at its active level, the corresponding buffer passes its non-inverting input to the output. When the enable input is inactive, that output enters a high-impedance state and stops driving the connected net. This makes the SN74HC126N useful for bus isolation, bidirectional transceiver interfacing, test-point multiplexing, and systems that must park outputs safely during reset or power transitions.
The 2 V to 6 V supply range allows operation from low-voltage systems such as 2.5 V and 3.3 V rails through conventional 5 V logic. Because the outputs can enter a high-impedance state, external pull-up or pull-down resistors normally establish the state of a bus during disabled periods. The 14-pin through-hole package supports conventional DIP assembly, prototyping, and repair rather than high-density surface-mount layouts.
Typical uses include computer and peripheral bus buffering, memory-module interface isolation, industrial control boards, and shared data buses where multiple sources must be disconnected electrically. In each case, the enable controller must guarantee that only one buffer drives a net at a time. The high-impedance state should also be considered during power-up, reset, and hot-plug transitions to prevent undefined drive currents.
A practical design point is to control each output-enable input with a defined logic level and account for bus capacitance, pull resistor strength, and the switching limits listed in the manufacturer datasheet. The datasheet also permits driving a high-impedance CMOS input, but the total capacitive load must remain within the specified maximum. For new compact designs, the surface-mount form of the SN74HC126 family is generally preferred.
This page combines the manufacturer product information, distributor availability data, cross-reference research, pin-level implementation guidance, and application-oriented engineering notes. It is intended to help designers confirm footprint compatibility, output-enable behavior, supply requirements, and bus loading before committing the part to a new board.
Bộ thay thế dễ dàng lắp đặt cho SN74HC126N — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
CD74HC126E
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MC74HC126N
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
74HC126N
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
TC74HC126P
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
HCF126M013
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SN74HC126N Tỷ lệ tối đa & tính chất điện
| Number of Channels | 4 channels |
| Operating Supply Voltage Range | 2 V to 6 V |
| Logic Type | Non-inverting |
| Output State | 3-state, high-impedance output |
| Device Function | Quadruple bus buffer / line driver |
| Elements per Channel | 1 bit |
| Số lượng đầu ra | 4 outputs |
| Number of Output Enables | 4 independently controlled output enables |
| Output Enable Polarity | Active high |
| Package Type | 14-pin through-hole DIP |
| Kiểu lắp đặt | Through-hole |
| Logic Family | 74HC CMOS |
Cấu hình chân SN74HC126N
| Chân 1 | 1OE — Output enable for channel 1; high enables the output and low places it in a high-impedance state |
| Chân 2 | 1A — Data input for channel 1 |
| Chân 3 | 1Y — Non-inverting output for channel 1 |
| Chân 4 | 2OE — Output enable for channel 2; high enables the output and low places it in a high-impedance state |
| Chân 5 | 2A — Data input for channel 2 |
| Chân 6 | 2Y — Non-inverting output for channel 2 |
| Chân 7 | GND — Ground reference |
| Chân 8 | 3OE — Output enable for channel 3; high enables the output and low places it in a high-impedance state |
| Chân 9 | 3A — Data input for channel 3 |
| Chân 10 | 3Y — Non-inverting output for channel 3 |
| Chân 11 | 4OE — Output enable for channel 4; high enables the output and low places it in a high-impedance state |
| Chân 12 | 4A — Data input for channel 4 |
| Chân 13 | 4Y — Non-inverting output for channel 4 |
| Chân 14 | VCC — Power supply input |
Ứng dụng tiêu biểu
SN74HC126N phù hợp cho 6 Áp dụngs: Shared Computer and Peripheral Buses, Memory and Peripheral Interface Isolation, Industrial Control and Automation Boards, Bidirectional Transceiver Interfaces, Test and Measurement Signal Multiplexing, Legacy Embedded System Retrofitting.
Shared Computer and Peripheral Buses
The SN74HC126N fits shared-bus designs because each of its four non-inverting buffers can drive a logic net or disconnect electrically through an active-high output enable. Place one buffer between a source device and a bus segment when the source must be isolated during another module's access cycle. The 2 V to 6 V operating range supports 2.5 V, 3.3 V, and 5 V legacy systems, while the 3-state output prevents two enabled drivers from fighting over the same net. Confirm the connected bus capacitance and pull-resistor strength against the Texas Instruments switching-characteristics limits, and guarantee that only one driver is enabled at any time.
Được đề xuất
Memory and Peripheral Interface Isolation
The SN74HC126N is useful between memory or peripheral interfaces and a multi-source bus because its individual active-high enables can hold unused outputs in a high-impedance state. This prevents an unselected device from loading address, data, or control lines and allows several memory devices to share routing resources. The four independent channels can handle four directional or multiplexed signals without changing the source logic. Use pull-up or pull-down resistors where a disconnected line must remain at a valid CMOS level, and check the datasheet's maximum capacitive-load figure against long PCB traces and package interconnects.
Được đề xuất
Industrial Control and Automation Boards
The SN74HC126N supports industrial control boards that combine several CMOS logic sources on common data or command buses. Its 2 V to 6 V supply range is useful for mixed-voltage control systems operating at 3.3 V or 5 V, while the non-inverting buffers preserve existing logic polarity. The three-state outputs let a controller isolate a fieldbus interface, sensor-conditioning logic, or actuator-driver section during reset. Because industrial systems can have long wiring and noisy environments, keep the logic net short where possible, validate the bus capacitance, and rely on pull resistors to establish safe levels while outputs are disabled.
Được đề xuất
Bidirectional Transceiver Interfaces
The SN74HC126N can support bidirectional communication paths where a shared conductor must accommodate more than one possible driver. Separate the transmit and receive paths with individual SN74HC126N channels and assert only the enable associated with the active direction. The disabled channel presents a high impedance rather than driving the line, which is essential when the opposite side of the interface is transmitting. Pull resistors can bias the shared conductor during direction changes, and their values must balance bus rise time against load current. Verify timing against the system clock and confirm that no control overlap can enable both drivers simultaneously.
Được đề xuất
Test and Measurement Signal Multiplexing
The SN74HC126N can isolate several sensed or generated logic signals in a test and measurement system so that one acquisition bus is not disturbed by every connected circuit. Each active-high enable selects whether a particular source continues to drive the shared test point or becomes high impedance. This arrangement helps reduce contention and allows unused circuits to remain connected physically. Select pull values to preserve the intended idle level, keep probe and fixture capacitance within the allowed total load, and observe the specified switching limits when changing enable states rapidly.
Được đề xuất
Legacy Embedded System Retrofitting
The SN74HC126N is a practical choice when maintaining a 5 V through-hole control board that needs stronger bus drive or removable drivers during troubleshooting. Its 14-pin DIP package fits conventional socketed or leaded layouts, and its 74HC-compatible 2 V to 6 V range allows operation within existing system tolerances. Four channels can isolate four contended nets without redesigning the surrounding logic. Before installation, confirm the exact pin assignment, verify that the board does not exceed the allowed capacitive load, and use a logic analyzer to confirm that output-enable transitions never create a moment with two drivers active.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho SN74HC126N — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | CD74HC126E | MC74HC126N | 74HC126N | TC74HC126P | HCF126M013 |
|---|---|---|---|---|---|---|
| Package | 14-pin DIP | 14-pin DIP | 14-pin DIP | 14-pin DIP | 14-pin DIP | 14-pin DIP |
| Brand | Texas Instruments | Texas Instruments | onsemi | onsemi | Toshiba | STMicroelectronics |
| Number of Channels | 4 | 4 | 4 | 4 | 4 | 4 |
| Logic Type | Non-inverting buffer | Non-inverting buffer | Non-inverting buffer | Non-inverting buffer | Non-inverting buffer | Non-inverting buffer |
| Output State | 3-state, high impedance when disabled | 3-state, high impedance when disabled | 3-state, high impedance when disabled | 3-state, high impedance when disabled | 3-state, high impedance when disabled | 3-state, high impedance when disabled |
| Output Enable Polarity | Active high | Active high | Active high | Active high | Active high | Active high |
| Operating Supply Voltage Range | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V |
Bảo phân biệt quan trọng
- Manufacturer-specific ordering code with a consolidated Texas Instruments product and quality documentation set (vs74HC126N)
- Direct functional equivalent with the same four-channel active-high 3-state architecture (vsCD74HC126E)
- Broader supply-voltage operating window than many older bipolar bus-driver families (vsMC74HC126N)
Ghi chú thiết kế
Never enable two SN74HC126N outputs that are connected to the same net. The device supports high-impedance bus sharing, but it does not resolve drive contention between simultaneously active outputs. Design the enable controller so that it produces a valid break-before-make sequence, and use pull-up or pull-down resistors to establish a defined state whenever all drivers are disabled.
The SN74HC126N operates from 2 V to 6 V, but the usable timing margin depends on the actual rail level and the total capacitive load. Include package parasitics, PCB trace capacitance, connector capacitance, and the input capacitance of the driven device when checking the switching limits. Avoid relying on a nominal 5 V rail to guarantee operation if the system can fall outside the component's rated supply range.
Keep disabled outputs from being treated as signal sources. A high-impedance output can float to an unintended level, so add a pull resistor whenever the downstream receiver must interpret a stable value during reset, disable, or bus handoff. Select the resistor with the bus rise-time requirement and the enabled driver's current capability in mind, and verify the resulting level against the receiving device's input thresholds.
Thông tin tuân thủ
The SN74HC126N is a general-purpose 74HC CMOS logic IC rather than an automotive-qualified device. Compliance attributes should be confirmed for the exact manufacturing site and orderable suffix through the manufacturer product documentation.