Texas Instruments

SN74HC640N - 8-Bit 3-State Bus Transceiver | TI

MPN: SN74HC640N ✓ فعال
2 V to 6 V Vdss 20-pin PDIP Package
MOQ: 1 |

SN74HC640N جائزہ

The Texas Instruments SN74HC640N is an 8-bit inverting bus transceiver with 3-state outputs, supplied in a 20-pin PDIP package for a -40°C to +85°C operating range. Its eight channels share direction control through DIR and output enable through OE. The device supports the 74HC CMOS logic family and is intended for bidirectional parallel-bus buffering, isolation, and data-direction control.

A bus transceiver is an interface device that connects two digital buses while controlling signal direction and output state. The SN74HC640 belongs to the CMOS logic hierarchy, where a transceiver sits between bus-controller outputs and external data lines. Its bidirectional architecture allows eight data paths to transmit in either direction, while the 3-state outputs permit a shared bus to be disconnected when another device needs control.

The SN74HC640N provides eight independently described data channels in one package. DIR establishes the operating direction for all channels, and OE independently controls whether the outputs are active or high impedance. This arrangement simplifies control logic in systems that route data among multiple bus masters, memory devices, interface controllers, or data-conversion subsystems without introducing a separate direction-control line for every bit.

The device uses positive-edge-triggered data transfer when the direction and output-enable states permit operation. Because the transceiver inverts the bus signal, the receiving circuit receives the complement of the transmitted logic level. Designers must account for this inversion in software, protocol handling, test fixtures, and any logic-level conversion or inversion placed downstream of the SN74HC640N.

Typical applications include bidirectional data acquisition, embedded processor bus expansion, memory-interface routing, test-equipment signal conditioning, and industrial control systems that need controlled access to a shared parallel bus. The 20-pin PDIP package also supports through-hole assembly and prototype boards where a socketed device is useful for replacement or logic testing.

For reliable operation, connect the enable and direction controls to valid CMOS logic levels, route all eight bus paths consistently, and ensure that only one enabled device drives the shared bus at a time. The TI datasheet pin configuration and truth table should be used directly when assigning PCB signals and validating read-versus-write behavior.

This page combines package and ordering information, functional guidance, pin-level implementation details, and a practical comparison framework for compatible octal 74HC-style transceivers, helping engineers move from datasheet lookup to a board-ready design decision.

کے لیے ڈراپ اِن متبادل SN74HC640N — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

SN74HC640NE4

✅ ڈراپ-اِن
📦 PDIP-20
Identical documented 2 V to 6 V octal inverting 3-state transceiver function; the distinguishing factor is the ordering designation rather than a measured electrical difference.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

74HC640N

✅ ڈراپ-اِن
📦 PDIP-20
Documents the same 8-bit, 2 V to 6 V, inverting 3-state bus-transceiver function in 20 pins; manufacturer-specific timing and qualification remain to be compared.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

CD74HC640EE4

✅ ڈراپ-اِن
📦 PDIP-20
Matches the 20-pin, 8-bit, 2 V to 6 V inverting 3-state transceiver description; detailed timing and control-characteristic differences require datasheet verification.

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

SN74HC640N زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

Product Type Octal bus transceiver
Number of Elements 1 element
Bits per Element 8 bits
Logic Type Inverting
Output State 3-state
Number of Channels 8 channels
Supply Voltage Range 2 V to 6 V
آپریٹنگ درجہ حرارت رینج -40°C to +85°C
پیکیج 20-pin PDIP
پنز کی تعداد 20 pins
ماؤنٹنگ ٹائپ Through-hole
Direction Control DIR input
Output Enable Control OE input
Transfer Direction Control Shared by all 8 channels

SN74HC640N پن کنفیگریشن

DIP-20 Package Pinout Diagram DIP-20 20-pin dual inline, 7.62mm pitch, JEDEC MS-001. 1 20 2 19 3 18 4 17 5 16 6 15 7 14 8 13 9 12 10 11 DIP-20
پن 1 1A — Data input or output for channel 1
پن 2 1B — Data input or output for channel 1
پن 3 2A — Data input or output for channel 2
پن 4 2B — Data input or output for channel 2
پن 5 3A — Data input or output for channel 3
پن 6 3B — Data input or output for channel 3
پن 7 4A — Data input or output for channel 4
پن 8 4B — Data input or output for channel 4
پن 9 DIR — Direction control input
پن 10 OE — Output enable input
پن 11 GND — Ground
پن 12 5A — Data input or output for channel 5
پن 13 5B — Data input or output for channel 5
پن 14 6A — Data input or output for channel 6
پن 15 6B — Data input or output for channel 6
پن 16 7A — Data input or output for channel 7
پن 17 7B — Data input or output for channel 7
پن 18 8A — Data input or output for channel 8
پن 19 8B — Data input or output for channel 8
پن 20 VCC — Power supply

عام استعمالات

SN74HC640N کے لیے موزوں ہے 6 ایپلیکیشنs: Shared Parallel Data Bus, Embedded Processor Bus Expansion, Data Acquisition Interface, Test and Measurement Signal Routing, Industrial Control Signal Conditioning, Memory Interface Routing.

🖥️

Shared Parallel Data Bus

The SN74HC640N fits a shared parallel bus because its eight inverting channels can change direction under the common DIR input while OE isolates the outputs when another device owns the bus. The 2 V to 6 V supply range supports conventional 74HC CMOS systems, and the 20-pin PDIP package simplifies through-hole prototyping. Designers should keep every data channel under consistent bus-direction control and permit only one enabled output driver on each shared node. Because the transceiver inverts logic levels, external inversion or corresponding software treatment may be necessary. Pull-up or pull-down requirements and unused control states should be checked against the manufacturer datasheet before routing the PCB.

🔧

Embedded Processor Bus Expansion

The SN74HC640N can buffer or isolate eight parallel processor-interface signals when a board requires bidirectional routing between a controller and peripheral bus. Common DIR and OE control reduces the external control-pin burden, while the eight 3-state channels support shared-bus participation. Its 2 V to 6 V operating range aligns with standard 74HC interface levels, but the system designer must confirm the processor voltage, timing, and required logic polarity. The inverting architecture means that firmware and hardware timing diagrams should use the effective inverted transfer behavior. The 20-pin PDIP format is particularly convenient for prototype and legacy-system expansion where socketed through-hole assembly is preferred.

📡

Data Acquisition Interface

The SN74HC640N can provide controlled eight-bit data isolation in acquisition equipment where a converter or sensor interface must connect to a shared digital bus. Its 3-state outputs permit the acquisition channel to release the bus during other transfers, and the shared DIR input simplifies switching between control and data paths. The 8-bit channel count maps naturally to parallel converter output groups, although the complete signal sequence must be adjusted for the device's inverting operation. Operating across the -40°C to +85°C range supports industrial and laboratory environments when the rest of the circuit meets its own environmental limits. Timing margins and logic thresholds should be checked against the selected acquisition components.

🧰

Test and Measurement Signal Routing

The SN74HC640N is useful in test fixtures and instrument signal-routing circuits that need to connect eight measurement lines to a common controller bus without leaving multiple outputs continuously active. DIR selects the route through all channels, while OE places the device in a high-impedance state during test sequences or instrument hand-off. The 20-pin PDIP package is convenient for socketed boards, probe fixtures, and legacy test systems. Because the device inverts every enabled data path, test-limit calculations and expected waveforms must reflect that polarity. Use the manufacturer truth table to establish control timing, and verify signal integrity at the system clock and bus-loading conditions used by the final fixture.

🏭

Industrial Control Signal Conditioning

The SN74HC640N can condition and route eight digital control or status lines in industrial equipment operating across its -40°C to +85°C range. Its shared DIR and OE controls allow a controller to take ownership of a bus or release it for another subsystem, reducing the number of dedicated multiplexing controls on the host board. The 2 V to 6 V supply compatibility supports 74HC logic families, but external systems must ensure compatible thresholds and timing. The inverting transfer characteristic should be included in ladder-logic interpretation or control-code design. Designers should also keep disabled outputs high impedance and use the device within the absolute maximum ratings specified for the selected supplier and package variant.

🗄️

Memory Interface Routing

The SN74HC640N can route eight parallel memory-interface signals when a controller must share address, data, or control paths with another bus owner. Its 3-state output capability is valuable in multiplexed memory systems because OE can prevent the transceiver from driving a line while another device is active. DIR provides a common direction change for all eight paths, simplifying state-machine control at the board level. The inverting behavior must be included in memory-command and address decoding logic, and setup or hold timing must be checked against the actual memory and transceiver specifications. The PDIP package is especially useful in legacy controller cards and prototype platforms where a socketed through-hole implementation accelerates rework.

تجویز کردہ پروڈکٹس کا خلاصہ

SN74HC640N Texas Instruments استعمال ہوتا ہے: Shared Parallel Data Bus, Embedded Processor Bus Expansion, Data Acquisition Interface, Test and Measurement Signal Routing, Industrial Control Signal Conditioning, Memory Interface Routing 74HC640N Second-source bus transceiver استعمال ہوتا ہے: Shared Parallel Data Bus, Test and Measurement Signal Routing SN74HC640NE4 Related ordering designation استعمال ہوتا ہے: Embedded Processor Bus Expansion, Industrial Control Signal Conditioning CD74HC640EE4 Second-source transceiver استعمال ہوتا ہے: Data Acquisition Interface, Memory Interface Routing
What is the SN74HC640N?
The SN74HC640N is an octal inverting bus transceiver with eight 3-state data channels in a 20-pin PDIP package. According to the Texas Instruments manufacturer datasheet, all eight channels are controlled by a common direction input, DIR, and a common output-enable input, OE. The device supports a 2 V to 6 V supply range and a -40°C to +85°C operating-temperature range.
Where can I download the SN74HC640N datasheet PDF?
The official SN74HC640N datasheet PDF is available from the Texas Instruments product page at https://www.ti.com/lit/ds/symlink/sn74hc640.pdf. According to Texas Instruments, the document covers the SNx4HC640 octal bus-transceiver family, including the SN74HC640N configuration, DIR and OE control behavior, 3-state outputs, electrical characteristics, and the 20-pin PDIP pinout.
Where can I find the SN74HC640N pinout?
The SN74HC640N pinout is shown in the Texas Instruments manufacturer datasheet, with 20 pins organized as eight paired data inputs and outputs plus DIR, OE, GND, and VCC. The official PDF at https://www.ti.com/lit/ds/symlink/sn74hc640.pdf should be used when assigning PCB tracks or wiring a socketed prototype because the inverting data channels and control pins have specific numbered locations.
How does the SN74HC640N DIR and OE control work?
The DIR and OE inputs on the SN74HC640N determine the direction and output state of all eight data channels. According to the Texas Instruments manufacturer datasheet, DIR selects the transmit direction for the complete device, while OE controls whether the outputs are active or placed in the high-impedance state. Keeping OE inactive allows multiple devices to share a parallel bus without creating output contention.
Does the SN74HC640N invert the bus data?
Yes, the SN74HC640N uses inverting data channels, so a low input level produces a high output level when the corresponding channel is enabled and transmitting. According to the Texas Instruments manufacturer datasheet, all eight channels share this behavior. Account for the inversion in bus protocols, firmware, test patterns, and any logic that compares source and destination data.
What is the SN74HC640N supply-voltage range?
The SN74HC640N operates from a 2 V to 6 V supply, placing it in the 74HC CMOS logic family. According to the Texas Instruments manufacturer datasheet, the device includes eight inverting channels with 3-state outputs and common DIR and OE controls. Use supply voltage and input levels compatible with the selected HC-family system, and do not exceed the datasheet limits.
Where can I buy SN74HC640N online?
The SN74HC640N can be requested through the Request a Quote form on this product page, where package, quantity, and production requirements should be stated. The Texas Instruments product page identifies SN74HC640N as a 20-pin PDIP device rated for -40°C to +85°C. Current commercial terms, availability, and lead time should be confirmed through the quote workflow.
What is the price of SN74HC640N?
Current SN74HC640N commercial pricing is handled through the Request a Quote form on this page. The form is the appropriate route for checking price, stock, quantity breaks, and lead time for the exact 20-pin PDIP orderable part. Requesting the exact MPN helps prevent confusion with related SN74HC640 package, temperature, or reel-code variants.
What is the lead time for SN74HC640N?
Use the Request a Quote form on this page to request the current SN74HC640N lead time and available production quantity. Lead time can depend on order volume, scheduled builds, and packaging requirements. The Texas Instruments manufacturer datasheet and product page define the device as the SN74HC640N in a 20-pin PDIP package, allowing procurement to quote the exact ordering code.
Is SN74HC640N in stock?
Current SN74HC640N inventory should be confirmed through the Request a Quote form on this product page. Enter the required quantity and packaging preference so the quote response reflects the exact 20-pin PDIP device. This approach avoids treating a general family listing or a related 74HC transceiver as proof that the SN74HC640N orderable part is available.
SN74HC640N vs SN74HC640NE4 - which is better for a new design?
SN74HC640N and SN74HC640NE4 provide the same octal inverting 3-state transceiver function and 20-pin PDIP footprint, so the choice primarily concerns ordering and packaging qualification. According to the Texas Instruments product information, SN74HC640N is the standard N-package ordering option, while SN74HC640NE4 is a related ordering designation. Confirm the exact suffix required by your assembly and procurement process.
When should I choose SN74HC640N instead of 74HC640N?
Choose SN74HC640N when procurement documentation specifically requires the Texas Instruments ordering designation; choose 74HC640N when the NXP device has been qualified for the complete system. According to the Texas Instruments manufacturer datasheet, the SN74HC640 implements eight inverting 3-state channels with common DIR and OE control in a 20-pin PDIP package, matching the documented 74HC640N alternative function.
Is SN74HC640N suitable for a shared parallel bus?
Yes, the SN74HC640N is suitable for a shared parallel bus when OE is used to disable all outputs except the active driver. According to the Texas Instruments manufacturer datasheet, DIR controls all eight channel directions and OE provides common output enable control. The design must also ensure that no two enabled devices drive the same bus node simultaneously.
What can replace SN74HC640N?
The SN74HC640NE4, 74HC640N, and CD74HC640EE4 are documented 20-DIP alternatives for the SN74HC640N function. According to the Texas Instruments manufacturer datasheet, the SN74HC640 uses eight inverting 3-state channels with common DIR and OE controls. Before substitution, verify supply voltage, timing, enable polarity, and the complete 20-pin signal mapping against the selected replacement.
Is CD74HC640EE4 a drop-in replacement for SN74HC640N?
CD74HC640EE4 is a documented 20-DIP alternative with the same octal inverting 3-state transceiver function, but it should be treated as a second-source option requiring qualification rather than an automatic substitution. According to the Texas Instruments manufacturer datasheet, the SN74HC640N uses eight inverting channels with shared DIR and OE controls. Verify timing, control polarity, and absolute maximum conditions before production use.
What are the key specifications of SN74HC640N that engineers should know?
The key SN74HC640N specifications are eight inverting data channels, 3-state outputs, common DIR and OE controls, a 2 V to 6 V supply range, a 20-pin PDIP package, and a -40°C to +85°C operating range. According to the Texas Instruments manufacturer datasheet, all eight channels change direction together. Engineers should also account for signal inversion and prevent contention on shared output nodes.

کے لیے انجینئرنگ ریفرنس ڈیٹا SN74HC640N — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose SN74HC640N when the design requires a Texas Instruments octal inverting transceiver in a 20-pin PDIP package, particularly for through-hole prototypes, socketed legacy assemblies, or shared parallel buses with common DIR and OE control. Its 2 V to 6 V supply range supports standard 74HC systems, while the inverting transfer characteristic must be reflected in firmware, test limits, and control logic. SN74HC640NE4 is a closely related ordering designation that should be preferred when it is the exact part required by an approved BOM or assembly drawing. Consider 74HC640N when a second manufacturer is strategically valuable and the NXP timing, qualification, and sourcing details have passed engineering review. CD74HC640EE4 is another documented 20-DIP option, but detailed propagation delay, control-state, and qualification comparisons must be completed before substitution. For any replacement, confirm the complete pin mapping, supply range, enable polarity, and timing rather than relying only on the 74HC640 function description.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ SN74HC640NE4 74HC640N CD74HC640EE4
Manufacturer Texas Instruments Texas Instruments NXP Semiconductors Texas Instruments
Package 20-pin PDIP 20-pin PDIP 20-pin PDIP 20-pin PDIP
Logic Type Inverting Inverting Inverting Inverting
Number of Channels 8 channels 8 channels 8 channels 8 channels
Output State 3-state 3-state 3-state 3-state
Supply Voltage Range 2 V to 6 V 2 V to 6 V 2 V to 6 V 2 V to 6 V
Direction Control Shared DIR input Shared DIR input Shared DIR input Shared DIR input
Output Enable Control Shared OE input Shared OE input Shared OE input Shared OE input

اہم امتیازی خصوصیات

  • Shared control simplifies eight-channel bus direction management (بمقابلہ74HC640N)
  • Identifiable 20-pin PDIP implementation for through-hole assembly (بمقابلہSN74HC640NE4)
  • Three-state bus isolation supports shared parallel buses (بمقابلہCD74HC640EE4)

ڈیزائن نوٹس

Do not allow two enabled SN74HC640N devices to drive the same parallel-bus node. Use OE to isolate inactive devices and assert it only after DIR and the receiving device are prepared. Because all eight channels invert the signal, verify command interpretation and test patterns after a logic inversion. A bus that appears to have sporadic data corruption can result from output contention rather than a failed transceiver.

Route each numbered A and B data channel as a matched bidirectional path and keep the DIR and OE traces away from sensitive analog or high-speed clock nets. Place any required bus termination close to the driven endpoint and use a ground plane that remains continuous beneath the PDIP footprint. Do not add trace stubs merely to reproduce a generic bus layout; calculate termination from the final trace impedance, load, and clock rate.

Decouple the VCC pin close to the package with the capacitance and voltage rating required by the Texas Instruments manufacturer datasheet. Keep the supply return path short and connect the GND pin to the board ground plane without sharing a narrow path with unrelated high-current loads. When the transceiver is used in 74HC systems operating away from 5 V, recheck input thresholds, output levels, and timing rather than assuming 5 V CMOS behavior.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for this exact ordering option. AEC-Q100 status is not applicable to this commercial 74HC logic device based on the identified product class.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-14 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

SN74HC640N datasheet SN74HC640N pinout SN74HC640N datasheet pdf SN74HC640N equivalent SN74HC640N replacement SN74HC640N cross reference SN74HC640N vs 74HC640N SN74HC640N price SN74HC640N stock Texas Instruments SN74HC640N SN74HC640N 20-pin PDIP SN74HC640N bus transceiver application

متعلقہ اجزاء اور اصطلاحات

Texas Instruments SN74HC640N SN74HC640 SN74HC640NE4 74HC640N CD74HC640EE4 NXP Semiconductors octal bus transceiver bus transceiver CMOS logic 74HC logic family three-state output high-impedance output inverting logic bidirectional bus DIR control input OE control input parallel data bus PDIP-20 DIP package family through-hole mounting shared bus arbitration signal inversion 2 V to 6 V supply
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں