Texas Instruments

SN74LS467N - Octal 3-State Buffer | Texas Instruments

MPN: SN74LS467N ✓ فعال
5 V Vdss 24 mA Id 20-pin PDIP Package
MOQ: 1 |

SN74LS467N جائزہ

The Texas Instruments SN74LS467N is an octal buffer with three-state outputs, operating from a 5 V nominal supply in a 20-pin PDIP package. Its key operating characteristics include an 18 ns propagation delay and a maximum low-level output current of 24 mA. The device provides eight buffered output positions with three-state control for placing individual sections into a high-impedance state when they are not actively driving a bus.

A tri-state buffer is a digital logic component that presents a strong logic level when enabled and a high-impedance state when disabled. The high-impedance condition allows multiple devices to share a data bus without creating output conflicts. Within the broader semiconductor hierarchy, the SN74LS467N belongs to the logic IC family, where buffer and line-driver functions strengthen digital signals and provide controlled bus participation.

The SN74LS467N uses bipolar LS-series logic. Its 5 V nominal supply operation is compatible with conventional TTL signal environments, while the 18 ns propagation-delay figure provides defined timing for address, data, and control paths. The 24 mA maximum IOL specification is important when the output must sink current from a short bus or heavily loaded receiver. Because it is an eight-position device, one package can support multiple independently controlled bus segments when the application uses the appropriate enable structure.

Three-state outputs are most valuable when several physical devices connect to a common conductor. When all connected drivers are disabled simultaneously, the shared line can be released without permanently shorting it to a logic level. PCB design must still reserve adequate drive strength and termination for the intended bus topology. Long traces, capacitive loading, stubs, and simultaneous transitions can reduce practical timing margin even when the nominal propagation delay is suitable.

Typical uses include bus-interface buffering, digital signal isolation, address multiplexing, control-line routing, and industrial or legacy TTL systems. The 20-pin PDIP package also favors through-hole construction, repairable assemblies, prototyping, and equipment where leaded components are preferred over fine-pitch surface-mount packages. Its larger lead spacing also makes inspection and manual rework straightforward.

Designers should verify the enable truth table and signal states in the manufacturer datasheet before connecting unused sections. Keep disabled outputs electrically isolated from other drivers, maintain compatible logic thresholds throughout the bus, and account for the 18 ns delay in setup and hold timing. The 24 mA IOL limit should be checked against the worst-case load.

This product page combines the known electrical and package characteristics of the SN74LS467N with practical implementation guidance, source-backed purchasing information, and same-family replacement analysis for engineers evaluating legacy TTL bus-buffer designs.

کے لیے ڈراپ اِن متبادل SN74LS467N — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔

SN74LS467

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
📦 20-pin PDIP
Base family designation; the N suffix and ordering details must be confirmed before assembly, with no quantified electrical difference established

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

SN74LS467A

✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ
📦 20-pin PDIP
Revised family variant; exact propagation-delay, temperature, and suffix differences require datasheet confirmation

📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)

SN74LS467N زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات

Device Type Octal buffer with three-state outputs
Logic Family LS-series bipolar TTL
Number of Output Elements 8 elements
آؤٹ پٹ کی قسم 3-state, element per element
Nominal Supply Voltage 5 V
Propagation Delay 18 ns
Maximum Low-Level Output Current 24 mA
Package Type 20-pin PDIP
پن کی تعداد 20 pins
ماؤنٹنگ ٹائپ Through-hole

SN74LS467N 20-pin pdip پن کنفیگریشن گائیڈ

SN74LS467N (20-pin pdip پیکیج) کے لیے پن کنفیگریشن۔ اس ڈیجیٹل IC میں GPIO، کمیونیکیشن انٹرفیس (UART، SPI، I2C) اور پاور پنز شامل ہیں۔ متبادل پن فنکشنز اور کنفیگریشن آپشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ ایمبیڈڈ سسٹم ڈیزائن اور PCB لے آؤٹ کے لیے ضروری۔

SN74LS467N کے لیے 20-pin pdip پیکیج پن آؤٹ ڈایاگرام

کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں SN74LS467N.

رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔

عام استعمالات

SN74LS467N کے لیے موزوں ہے 6 ایپلیکیشنs: Legacy TTL Data Bus Buffering, Address Multiplexing, Control-Line Signal Isolation, Digital Test and Measurement Equipment, Industrial Control-System Backplanes, Legacy Processor Interface Buffering.

🔧

Legacy TTL Data Bus Buffering

The SN74LS467N fits a legacy 5 V TTL data bus where several buffered channels must connect to shared conductors. Its eight three-state output positions can be selectively enabled, while the 18 ns propagation delay provides a defined switching interval for conventional TTL timing. A 24 mA maximum low-level output current gives designers a clear sink-current ceiling when estimating worst-case bus loading. Keep enable decoding mutually exclusive so that no two enabled outputs drive the same line. Because this is a 20-pin through-hole device in a 5 V TTL environment, it is especially useful for maintaining existing through-hole control, test, or industrial equipment rather than introducing a mixed-voltage redesign.

🖥️

Address Multiplexing

The SN74LS467N can support address or control multiplexing in a 5 V digital system that needs multiple buffered fields to share common conductors. Its octal structure provides eight three-state output positions, and each disabled position releases the bus so another source can take control. The 18 ns propagation-delay characteristic must be included in the multiplexer timing budget alongside enable decoding delay and receiver settling. Designers should use the device truth table to ensure that data and address fields do not overlap incorrectly during each select interval. The 20-pin PDIP format is particularly practical in legacy backplanes, laboratory equipment, and repair assemblies where leaded logic packages are standard.

🏭

Control-Line Signal Isolation

The SN74LS467N is useful when control signals from a 5 V TTL source need buffering before driving a shared digital interface. Its three-state outputs allow a section to become high impedance during another device's active interval, preventing contention on shared control conductors. The 18 ns propagation delay provides a timing value for sequencing enable and data signals, while the 24 mA maximum IOL rating defines the usable sink-current margin. A practical implementation should keep the disabled-output node free of pull-ups or pull-downs that would interfere with intentional high-impedance operation. Verify polarity and timing in the manufacturer truth table before assigning functions to the 20 pins.

🔧

Digital Test and Measurement Equipment

The SN74LS467N can serve as a bus-interface element in 5 V TTL test and measurement equipment that must route control or data signals among several circuit sections. Its eight three-state outputs support shared-bus architecture, and its 18 ns propagation delay is suitable for conventional instrument-control buses when the enable timing is included correctly. The 24 mA IOL limit should be compared with the worst-case receiver and termination load to avoid excessive sink current. The 20-pin PDIP package is advantageous for repairable laboratory equipment and through-hole prototyping because it provides generous lead spacing, straightforward inspection, and easier manual replacement than a fine-pitch surface-mount logic package.

🏭

Industrial Control-System Backplanes

The SN74LS467N is applicable to legacy industrial control backplanes that use 5 V TTL signaling and require grouped bus outputs with three-state control. The octal device allows several signal lines to share conductors when only one driver section is enabled at a time. Its stated 18 ns propagation delay should be checked against backplane length, receiver capacitance, and any additional transceiver delay, while the 24 mA maximum IOL rating limits direct load current. Long or capacitive backplanes may require series damping to control edge rates. The through-hole 20-pin PDIP package also remains practical for repair-oriented industrial equipment built with leaded logic components.

🖥️

Legacy Processor Interface Buffering

The SN74LS467N can buffer legacy processor data or control lines where a shared 5 V TTL bus must support several possible drivers. The octal three-state architecture separates source signals from the shared conductors and permits unused outputs to remain inactive. Designers must incorporate the 18 ns propagation delay and the enable settling interval into processor setup and hold requirements. The 24 mA maximum low-level output current provides the primary current limit for receiver and termination analysis. Because the SN74LS467N is a 20-pin PDIP part, it is especially appropriate for maintaining an existing processor board without changing its footprint, provided the exact enable and data mapping matches the original circuit.

What is the SN74LS467N?
The SN74LS467N is an octal bipolar TTL buffer with three-state outputs. According to the Texas Instruments datasheet, it provides eight buffered output positions, uses a 5 V nominal supply, and is packaged in a 20-pin PDIP. Its three-state outputs can be disabled to release a shared bus, allowing the device to support multidrop digital data paths.
What are the key specifications of SN74LS467N that engineers should know?
The SN74LS467N combines eight three-state buffer outputs, a 5 V nominal supply, an 18 ns propagation delay, and a 24 mA maximum low-level output current in a 20-pin PDIP package. The Texas Instruments datasheet identifies the device as an octal buffer, while the 18 ns timing and 24 mA IOL ratings are important constraints for bus loading and system timing.
How fast is the SN74LS467N?
The SN74LS467N has a stated propagation delay of 18 ns. The Texas Instruments datasheet uses that figure to characterize the buffer's switching speed. In a practical bus, the available timing margin also depends on trace capacitance, receiver loading, enable timing, and the number of enabled drivers, so the device rating should be checked against the complete timing path.
Where can I download the SN74LS467N datasheet PDF?
The SN74LS467N datasheet is available through the linked PDF index for the Texas Instruments device. It describes the octal three-state-buffer function, 20-pin PDIP package, and associated electrical characteristics. Use the pin-description table and truth table in that document when assigning PCB signals, determining enable polarity, and validating every disabled-output state.
Where can I find the SN74LS467N pinout?
The SN74LS467N pinout is published in the Texas Instruments datasheet for the 20-pin PDIP package. Use the package drawing and pin-description table to map each enable input, data input, and three-state output. Do not infer enable polarity from generic 74LS conventions because the enable behavior must follow the specific truth table for this device.
Can multiple SN74LS467N devices share one data bus?
Yes, multiple SN74LS467N devices can share a bus when only one output driver is enabled at a time. The three-state output becomes high impedance when disabled, preventing a direct drive conflict between devices. The Texas Instruments datasheet defines the enable truth table, so system control logic must enforce mutually exclusive driver selection and prevent two enabled sections from driving the same conductor.
What can replace the SN74LS467N?
The closest same-family choices are SN74LS467 and SN74LS467A, subject to verification of the exact suffix, package, enable truth table, and electrical limits before substitution. Both are identified as members of the Texas Instruments SN74LS467 family, but a source change must still be checked against the manufacturer datasheet rather than accepted solely because the base function name matches.
Is the SN74LS467A a drop-in replacement for SN74LS467N?
The SN74LS467A can serve as a same-family replacement candidate when its package and pin configuration match the original board, but final approval requires a pin-by-pin and truth-table comparison. The SN74LS467N is specified as a 20-pin PDIP octal three-state buffer, while the exact package suffix and revised electrical characteristics of the candidate must be confirmed in the manufacturer datasheet.
What is the best cross-brand equivalent for the SN74LS467N?
No cross-brand drop-in equivalent is established by the available manufacturer and cross-reference information. A valid cross-brand replacement would need the same 20-pin PDIP footprint, matching enable pins, compatible three-state behavior, and electrical ratings within the original design limits. Avoid selecting a generic octal buffer solely by channel count because tri-state control and bus-loading requirements are more restrictive.
SN74LS467N vs SN74LS467A: which is better for a legacy TTL bus?
The SN74LS467A is the more practical candidate to evaluate when it provides the required 20-pin PDIP configuration and equivalent enable and output behavior. The SN74LS467N is identified as a 5 V octal three-state buffer with 18 ns propagation delay and 24 mA IOL. Choose the original or its close family member based on exact timing, temperature, lifecycle, and sourcing requirements.
When should I choose SN74LS467N over a newer bus-buffer family?
Choose the SN74LS467N when an existing 20-pin PDIP PCB uses its exact enable arrangement and the circuit operates with conventional 5 V TTL levels. A newer family may be preferable for a new design when lower supply voltage, faster edge rates, smaller footprint, or stronger modern bus features are required. For legacy repair, preserving the original footprint usually outweighs a redesign.
Is the SN74LS467N suitable for high-current or long-bus designs?
The SN74LS467N should be treated as a general-purpose legacy bus buffer rather than a long-distance or high-current driver. Its listed maximum low-level output current is 24 mA and its propagation delay is 18 ns. Use series termination and controlled topology where appropriate, and select a dedicated transceiver or line driver when loads, cable length, or edge-rate requirements exceed the buffer's intended operating envelope.
Where to buy SN74LS467N online?
Use the Request a Quote form on this page to request current SN74LS467N pricing, stock status, minimum order quantity, and lead time. The form provides a single channel for a product-specific quotation and avoids stale quantity-break information. Confirm the exact 20-pin PDIP ordering code before approving the order.
What is the price of the SN74LS467N?
Current SN74LS467N pricing is available through the Request a Quote form on this page. Submit the required quantity and target ship-to information to receive an up-to-date quotation. Because legacy stock and production volume can materially change availability, request the quote before budgeting the component for a new build or repair.
What is the lead time for SN74LS467N?
The current SN74LS467N lead time is established through the Request a Quote form on this page. Include the required quantity, delivery date, and approved manufacturer or distributor conditions when requesting the quotation. For repair work, request enough additional units to cover board-level rework risk rather than relying on a nominal single-piece availability statement.

کے لیے انجینئرنگ ریفرنس ڈیٹا SN74LS467N — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔

انتخاب کی گائیڈ

Choose the SN74LS467N when repairing or maintaining an existing 5 V TTL board that uses the exact 20-pin PDIP footprint, enable arrangement, and three-state bus architecture. Its documented characteristics include eight output positions, 18 ns propagation delay, and 24 mA maximum IOL. Evaluate SN74LS467 first when it matches the board's exact ordering suffix and device revision, then verify its electrical ratings against the original design. SN74LS467A is another same-family candidate, but its exact suffix, temperature grade, timing, and lifecycle should be checked before substitution. For a new 5 V design, compare a modern bus transceiver or buffer when lower voltage, faster edges, smaller packaging, stronger drive, or guaranteed multi-source availability is important. For a legacy repair, preserving the original footprint and logic thresholds generally provides lower risk than redesigning the interface.

متبادلات کے ساتھ موازنہ

پیرامیٹر یہ پروڈکٹ SN74LS467 SN74LS467A
Brand Texas Instruments Texas Instruments Texas Instruments
Package 20-pin PDIP 20-pin PDIP 20-pin PDIP
Function Octal buffer with three-state outputs Octal buffer with three-state outputs Octal buffer with three-state outputs
Output Elements 8 elements 8 elements 8 elements
Nominal Supply Voltage 5 V 5 V 5 V
Mounting Type Through-hole Through-hole Through-hole
Logic Family LS-series bipolar TTL LS-series bipolar TTL LS-series bipolar TTL

اہم امتیازی خصوصیات

  • Element-level tri-state control supports shared-bus designs (بمقابلہSN74LS467)
  • The original N ordering option is documented as a 20-pin PDIP device (بمقابلہSN74LS467A)
  • Established through-hole construction supports legacy PCB compatibility (بمقابلہSN74LS467)

ڈیزائن نوٹس

Do not enable two SN74LS467N output sections that drive the same conductor. Although the three-state outputs can be released, two simultaneously active drivers can create a direct logic conflict and excessive current. Build the enable decoder so that only one source owns each shared bus segment, and use the manufacturer truth table to verify active-high or active-low control behavior for every pin.

Include the stated 18 ns propagation delay, enable-transition delay, and receiver settling time when creating a timing budget. PCB capacitance and long traces can increase observed transition time beyond the nominal device figure. For long or lightly loaded lines, evaluate source termination rather than relying on the 24 mA IOL rating as a substitute for correct transmission-line design.

Maintain a common return path and place the device so shared-bus traces remain short and have controlled capacitive loading. The 20-pin PDIP package provides generous lead spacing, but pin-assignment mistakes remain easy without careful schematic review. Mark the orientation notch on the PCB, verify every enable and data signal, and inspect for solder bridges after hand soldering in legacy equipment.

Decouple the 5 V supply close to the device with the capacitance and placement prescribed by the manufacturer datasheet. Although the SN74LS467N is a logic IC rather than a power-conversion component, inadequate supply bypassing can add supply noise and reduce switching margin. Confirm that the 24 mA output-current rating is sufficient for the worst-case load while leaving margin for additional bus capacitance.

تعمیل کی معلومات

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
لیڈ فری
Unknown
ہیلوجن فری
Unknown
کنفلیکٹ منرلز
Unknown

The device is a conventional logic IC rather than an automotive-qualified AEC-Q100 component. RoHS, REACH, lead-free, and halogen-free status require confirmation from the current manufacturer product documentation or lot documentation.

ڈیٹا کی تصدیق کی تاریخ: 2026-11-14 — ڈیٹا XAIPART کی کمپوننٹ انجینئرنگ ٹیم کے ذریعے تصدیق شدہ اور ترتیب شدہ

متعلقہ تلاشیں

SN74LS467N datasheet SN74LS467N pinout SN74LS467N datasheet pdf SN74LS467N equivalent SN74LS467N replacement SN74LS467N drop-in replacement SN74LS467N price SN74LS467N stock Texas Instruments SN74LS467N SN74LS467N 20-pin PDIP SN74LS467N 18ns propagation delay SN74LS467N vs SN74LS467A

متعلقہ اجزاء اور اصطلاحات

Texas Instruments SN74LS467N SN74LS467 SN74LS467A octal buffer three-state output tri-state buffer logic IC buffer and line driver bipolar TTL LS-series logic 5 V TTL propagation delay maximum low-level output current high-impedance state bus driver data bus address multiplexing 20-pin PDIP through-hole package industrial control legacy processor interface signal buffering
فوری کوٹ RFQ
مکمل تفصیلات بھریں — ہماری سیلز ٹیم 24 گھنٹوں میں جواب دے گی
پارٹ نمبر مینوفیکچرر پیکج QTY ہدف قیمت کل رقم
✓
کوٹ جمع ہو گیا!

ہم 24 گھنٹوں کے اندر آپ کے ای میل کا جواب دیں گے

1
RFQ جمع ہو گیا
2
کوٹ موصول ہو گیا
3
آرڈر دے دیا گیا
4
ادائیگی
5
بھیج دیا گیا
6
ڈیلیور شدہ
RFQ تفصیلات دیکھیں