SN74LS193D - 4-Bit Synchronous Up/Down Counter | Texas Instruments
MPN: SN74LS193D ✓ فعالSN74LS193D جائزہ
A counter IC is a synchronous sequential-logic device that stores a binary value and changes that value in response to clock edges. The SN74LS193 belongs to the 74LS TTL family, which sits within the broader hierarchy of digital logic ICs, counters, binary counters, and standard-surface-mount logic. Because all internal flip-flops are clocked together, the four outputs update simultaneously instead of producing the ripple transitions associated with asynchronous counting stages.
The key functional features are a 4-bit counting capacity, independent up-count and down-count clocks, a load input for parallel initialization, an asynchronous clear input, and a carry output for detecting overflow or underflow. The verified manufacturer description identifies the SN74LS193 as a synchronous 4-bit up/down binary counter with dual clock and clear. Its 16-SOIC package supports conventional surface-mount PCB assembly and is compatible with standard digital-logic design practices.
Synchronous operation is the device's principal engineering advantage. Since the four output bits change on the same active clock edge, downstream combinational logic sees a coherent new binary state rather than intermediate count values. This simplifies decoding and reduces uncertainty in control systems. The separate clock inputs also allow the same physical counter to perform upward counting, downward counting, or operation from a selected direction-control clock without redesigning the board.
Typical uses include programmable sequence generators, pulse and event counters, digital position indicators, frequency-divider stages, and control systems for industrial equipment. A load input can establish an initial count, and the carry output can flag the terminal count of 1111 during up counting or 0000 during down counting. These functions allow a single counter IC to coordinate multistage digital operations without requiring several separate accumulator devices.
PCB design should preserve clear access to the clock, load, and clear inputs because asynchronous control signals must not be allowed to float. Use a defined logic level for every input and route clock traces away from noisy switching nodes. The manufacturer datasheet should be consulted for the exact pin-description table, recommended operating conditions, timing limits, and maximum input voltages before finalizing the circuit.
This page combines the manufacturer function description, distributor package and pricing references, verified substitute data, and practical implementation guidance for engineers evaluating the SN74LS193D in legacy TTL, industrial-control, counter, and sequencing designs.
کے لیے ڈراپ اِن متبادل SN74LS193D — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
SN74LS193D
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →SN74LS193D
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →SN74LS193DM
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
74HC193D
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
74HCT193D
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
SN74LS193D زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Counter Type | Synchronous binary up/down counter |
| Counting Element | 1 element |
| Count Width | 4 bits |
| Counting Direction | Up or down |
| Clock Inputs | 2 independent clock inputs |
| Clock Edge | Positive edge |
| Clear Function | Asynchronous clear |
| Load Function | Parallel load |
| Carry Function | Overflow and underflow output |
| آؤٹ پٹ کی قسم | 4 parallel binary outputs |
| Logic Family | 74LS TTL |
| پیکیج | 16-SOIC, 0.154 inch body width, 3.90 mm width |
| ماؤنٹنگ ٹائپ | Surface mount |
SN74LS193D پن کنفیگریشن
| پن 1 | CLR — Asynchronous clear input |
| پن 2 | CLK DOWN — Down-count clock input |
| پن 3 | CLK UP — Up-count clock input |
| پن 4 | Q0 — Counter output Q0 |
| پن 5 | Q1 — Counter output Q1 |
| پن 6 | Q2 — Counter output Q2 |
| پن 7 | Q3 — Counter output Q3 |
| پن 8 | GND — Ground reference |
| پن 9 | LOAD — Parallel load control input |
| پن 10 | CARRY — Carry and borrow output |
| پن 11 | QA — Counter output A |
| پن 12 | QB — Counter output B |
| پن 13 | QC — Counter output C |
| پن 14 | QD — Counter output D |
| پن 15 | VCC — Power supply input |
| پن 16 | NC — Not connected |
عام استعمالات
SN74LS193D کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Sequence Controller, Programmable Pulse Counter, Frequency Divider, Digital Position Indicator, Digital Control System, Test and Measurement Counter.
Industrial Sequence Controller
The SN74LS193D fits industrial sequence-control logic because its four outputs change synchronously on the selected clock edge, giving downstream logic one coherent state to decode. Separate up and down clock inputs allow reversible sequences, while the load and clear controls establish or reset the initial state. The 16-SOIC package also simplifies maintenance of 74LS-based control boards. Confirm supply-voltage and timing limits against the Texas Instruments datasheet, especially when long field wiring connects directly to the counter inputs.
تجویز کردہ
Programmable Pulse Counter
The SN74LS193D can count incoming events in either direction when one of its two clock inputs is selected. A 4-bit count supports event totals from 00H to 1111, and the carry output can indicate the terminal count for use in a higher-order counting arrangement. Because the outputs are synchronous, a controller can decode the count without observing ripple transitions between valid binary states.
تجویز کردہ
Frequency Divider
For frequency division, the SN74LS193D uses one selected clock input and derives a lower-rate count state from its four binary outputs. The load and clear inputs allow a system to preset or reset the divider, while the carry output can mark overflow at the end of the count sequence. Designers should use the manufacturer timing data to establish the maximum usable input frequency and to preserve clock rise and fall requirements.
تجویز کردہ
Digital Position Indicator
The SN74LS193D can maintain a four-bit position state for a simple digital position or step counter. Its parallel outputs expose the current binary count, and synchronous state changes reduce intermediate decoding errors. The 16-SOIC package is useful in legacy instrumentation where replacing the logic family would require broader changes. Apply the clear and load controls according to the manufacturer pin table and confirm electrical behavior in the target operating environment.
تجویز کردہ
Digital Control System
The SN74LS193D fits legacy digital control systems that require a compact reversible state counter. Separate up and down clocks permit motion-command counting, while synchronous outputs let a state decoder act on a stable binary word. The clear and load inputs support initialization after reset or mode changes. For control equipment with long external leads, add suitable input conditioning and keep the counter’s clock path away from high-current switching nodes.
تجویز کردہ
Test and Measurement Counter
The SN74LS193D can serve as a low-order counting stage in test and measurement equipment where a 4-bit binary event count is required. Synchronous output updates simplify decoder logic, and the dual-clock interface permits count-up or count-down operation from separate event sources. Use the load control to establish a reference count and the carry indication to detect the terminal state. Validate clock timing and output transition requirements using the official manufacturer datasheet.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا SN74LS193D — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | SN74LS193D | SN74LS193D | SN74LS193DM | 74HC193D | 74HCT193D |
|---|---|---|---|---|---|---|
| Package | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC | 16-SOIC |
| Brand | Texas Instruments | ON Semiconductor | Signetics | Fairchild Semiconductor | Nexperia | Nexperia |
| Counter Type | Synchronous binary up/down counter | Synchronous binary up/down counter | Synchronous binary up/down counter | 74LS193 binary counter | 74HC193 binary counter | 74HCT193 binary counter |
| Count Width | 4 bits | 4 bits | 4 bits | 4 bits | 4 bits | 4 bits |
| Clock Inputs | 2 independent inputs | 2 independent inputs | 2 independent inputs | 2 independent inputs | 2 independent inputs | 2 independent inputs |
| Clear Function | Present | Present | Present | Present | Present | Present |
| Logic Family | 74LS | 74LS | 74LS | 74LS | 74HC | 74HCT |
| Number of Pins | 16 pins | 16 pins | 16 pins | 16 pins | 16 pins | 16 pins |
اہم امتیازی خصوصیات
- All four outputs change synchronously (بمقابلہ74HC193D)
- Separate up-count and down-count clock inputs (بمقابلہSN74LS191D)
- Original 74LS interface in a 16-SOIC footprint (بمقابلہ74HCT193D)
- Direct 74LS193 function match (بمقابلہSN74LS193DM)
ڈیزائن نوٹس
Do not leave the unused clock input floating. Define its inactive state at every operating mode and change direction only while the selected count requirement is satisfied. Because the device has separate up-count and down-count clocks, accidental pulses on the inactive clock can produce an unintended count. Use the manufacturer pin-description table to confirm active levels and clear the timing requirements before connecting external control logic.
Route the selected clock as a short, continuous trace and keep it away from switching-node copper and high-current return paths. The four counter outputs update synchronously, but valid data is still contingent on meeting setup and hold-time requirements. Use the manufacturer timing characteristics to determine the maximum external clock frequency, and add signal conditioning when the source is a mechanical switch, relay contact, or long cable.
Place the SN74LS193D according to the 16-SOIC footprint and preserve access to all clock, load, clear, output, and supply pins. Connect the ground and supply pins directly to appropriate planes or traces rather than routing return current through signal paths. For mixed analog and digital equipment, locate the counter away from analog inputs and provide a clear return path for switching currents.
Confirm the allowed supply range, input-voltage limits, and output-current ratings from the manufacturer datasheet before applying power. Decouple the supply connection locally with the capacitance and placement recommended by the device documentation. Legacy TTL circuits can experience threshold and timing shifts when supply voltage departs from the nominal condition, so validate both logic levels and maximum operating frequency across the expected supply tolerance.
تعمیل کی معلومات
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified in the manufacturer product-page snippet. The logical counter IC is not an automotive-qualified device unless a separate qualified ordering option is explicitly documented.