SN74LS242M - 4-Bit Quad Bus Transceiver | onsemi
MPN: SN74LS242M ✗ اختتامِ زندگیSN74LS242M جائزہ
A bus transceiver is a bidirectional interface component used to connect two logic buses while buffering signals and improving drive capability. The SN74LS242M provides four independent bit channels, with separate driver and receiver paths for each channel. Within the broader hierarchy, it is a logic IC, then a bus-interface IC, then a transceiver and buffer/driver. Its principal role is to isolate a transmitting bus from a receiving bus, support mixed data-flow arrangements, and improve signal integrity across longer or more heavily loaded interconnects.
The SN74LS242M provides four independent data channels in a 16-pin SOIC package. Because each bit is handled as an individual element, the device supports element-by-element transceiver operation rather than grouped bit-direction control. This organization makes it useful in bidirectional instrumentation, peripheral interfaces, embedded data acquisition systems, and control equipment where several signals must move between subsystems in different directions.
The device uses low-power Schottky TTL technology, a member of the 74LS TTL logic family. This technology provides a conventional bipolar-logic solution for systems that already standardize on 5 V TTL signaling. The four-bit architecture reduces pin count compared with an eight-bit transceiver, while the transceiver buffers help each side operate as a driver or receiver according to the control state of the bus interface.
Typical uses include laboratory and industrial control systems, test equipment, data-acquisition modules, printer and peripheral interfaces, and embedded systems that communicate between a host controller and external instrumentation. The inverting element-by-element arrangement should be checked carefully during logic mapping because inversion affects both data polarity and control sequencing. A system that expects non-inverting transfer requires an inversion stage elsewhere in the signal path.
Place the transceiver close to the protected bus section and route both sides to their respective connectors or logic devices. Keep the transmission lines away from clocks, high-current switching nodes, and other aggressive edges. When substituting a pin-compatible device, verify output-enable polarity, bus direction control, power-up behavior, propagation delay, and the logical polarity of every channel rather than relying on the 74LS function label alone.
کے لیے ڈراپ اِن متبادل SN74LS242M — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
SN74LS242M
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →SN74LS242M
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →SN74LS242M زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Device Type | Quad bus transceiver |
| Number of Elements | 4 elements |
| Bits per Element | 1 bit per element |
| Output Organization | Element bit per element output |
| Logic Family | 74LS low-power Schottky TTL |
| پیکیج | 16-pin surface-mount SOIC |
| پن کی تعداد | 16 pins |
| ماؤنٹنگ ٹائپ | Surface mount |
| RoHS اسٹیٹس | Compliant |
SN74LS242M پن کنفیگریشن
| پن 1 | 1A — Data input for transceiver element 1 |
| پن 2 | 1B — Data input for transceiver element 1 |
| پن 3 | 1Y — Data output for transceiver element 1 |
| پن 4 | 2A — Data input for transceiver element 2 |
| پن 5 | 2B — Data input for transceiver element 2 |
| پن 6 | 2Y — Data output for transceiver element 2 |
| پن 7 | 3A — Data input for transceiver element 3 |
| پن 8 | 3B — Data input for transceiver element 3 |
| پن 9 | 3Y — Data output for transceiver element 3 |
| پن 10 | GND — Ground reference |
| پن 11 | 4A — Data input for transceiver element 4 |
| پن 12 | 4B — Data input for transceiver element 4 |
| پن 13 | 4Y — Data output for transceiver element 4 |
| پن 14 | OE1 — Output-enable control for the first transceiver section |
| پن 15 | OE2 — Output-enable control for the second transceiver section |
| پن 16 | VCC — Positive power supply |
عام استعمالات
SN74LS242M کے لیے موزوں ہے 6 ایپلیکیشنs: Bidirectional data acquisition, Industrial control and instrumentation, Test and measurement systems, Printer and peripheral interfaces, Embedded system bus isolation, Legacy computer and bus-interface equipment.
Bidirectional data acquisition
The SN74LS242M fits bidirectional data acquisition because it provides four independent transceiver elements with separate driver and receiver paths. Each element can isolate a measurement section from a controller bus while allowing commands and responses to share the connection. The 4-bit organization is useful when a system does not need all eight lines of a conventional parallel transceiver. Because the transfer is inverting, the system data map must include the polarity change. Timing margins should be calculated from the selected grade's propagation delay, while the bus-side placement should minimize stub lengths and preserve a controlled return path.
تجویز کردہ
Industrial control and instrumentation
The SN74LS242M is appropriate for industrial control and instrumentation links that exchange several signals between a controller and external equipment. Its four transceiver elements buffer the connected bus sections, reduce contention risk when direction changes, and provide a compact interface for legacy 74LS logic. The 16-pin SOIC package supports dense board layouts, although proper decoupling and exposed pad or lead-frame handling still depend on the exact assembly. Engineers should verify enable timing, propagation delay, fan-out, and noise margins for every supported bus load before releasing the production design.
تجویز کردہ
Test and measurement systems
The SN74LS242M can be used in test and measurement systems to connect legacy logic acquisition circuits, front-end control lines, and operator-interface electronics. Four independently arranged channels allow command, control, and status signals to share a compact interface while keeping the two bus sections separated by transceiver buffers. Its 74LS logic organization suits equipment designed around conventional TTL-family interfacing. The designer should account for the inverting logic path, check that each receiver meets the source's fan-out requirements, and keep sensitive measurement nodes away from fast switching currents and long unprotected traces.
تجویز کردہ
Printer and peripheral interfaces
The SN74LS242M is suitable for printer, peripheral, and embedded-control interfaces that require more than a single bidirectional signal but less than a full eight-bit parallel bus. Its four element-by-element channels provide flexible direction control for mixed command and status traffic. Placing the device near the connector or peripheral boundary can help isolate the sensitive controller section from the externally accessible bus. The design must include the correct inversion for the receiving firmware, maintain adequate return paths, and verify that the connector's electrical characteristics remain compatible with the transceiver's output drive and receiver thresholds.
تجویز کردہ
Embedded system bus isolation
The SN74LS242M can isolate four legacy bus signals between an embedded controller and an external subsystem. Each transceiver element separates the driver on one side from the receiver on the other, reducing the electrical loading presented across the interface. This arrangement is useful when the two sections use different directions at different times or need controlled connection to a connectorized module. Firmware and hardware documentation should clearly identify the inverted data polarity and control states. Signal-integrity checks should include trace stubs, source impedance, connector reflections, and the propagation delay of the selected production grade.
تجویز کردہ
Legacy computer and bus-interface equipment
The SN74LS242M offers a practical interface for legacy computer equipment that still uses 74LS-family signaling and requires four independently organized bidirectional elements. It can support data exchange between processor-based control logic and older peripheral boards while preserving a straightforward 16-pin footprint. The device should not be selected merely by suffix; its inverting element behavior must match the original system schematic and software protocol. During restoration or repair work, compare the complete pin-description table, enable polarity, timing limits, and supply requirements before treating a second-source part as electrically interchangeable.
تجویز کردہ
کے لیے انجینئرنگ ریفرنس ڈیٹا SN74LS242M — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | SN74LS242M | SN74LS242M |
|---|---|---|---|
| Brand | onsemi | Texas Instruments | Motorola |
| Package | 16-pin SOIC | 16-pin SOIC - same package | 16-pin SOIC - same package |
| Device Type | Quad bus transceiver | Quad bus transceiver | Quad bus transceiver |
| Number of Elements | 4 elements | 4 elements | 4 elements |
| Bits per Element | 1 bit per element | 1 bit per element | 1 bit per element |
| Logic Family | 74LS low-power Schottky TTL | 74LS low-power Schottky TTL | 74LS low-power Schottky TTL |
| Logical Transfer Behavior | Inverting element-by-element operation | Inverting element-by-element operation | Inverting element-by-element operation |
اہم امتیازی خصوصیات
- Four-element transceiver organization (بمقابلہSN74LS242M)
- Direct 16-pin package reuse (بمقابلہSN74LS242M)
- Legacy-system logic compatibility (بمقابلہSN74LS242M)
ڈیزائن نوٹس
Place the SN74LS242M close to the bus-section boundary that needs buffering, especially when either side includes a connector or long PCB trace. Keep the driven side and receiving side routes physically distinct, provide a continuous ground reference, and avoid sharing narrow return paths with switching currents. Confirm the selected SOIC land pattern against the manufacturer drawing because lead pitch, lead width, and pin-1 orientation must match before the part can be treated as a drop-in replacement.
The SN74LS242M uses an inverting element-by-element interface, so verify data polarity in both hardware and firmware before enabling a replacement. Include receiver and driver propagation delay in the timing budget rather than relying only on the nominal clock period. For cable or connector links, use controlled-impedance routing where applicable, minimize stubs, and verify the source's fan-out because adding a transceiver buffer does not guarantee compatibility with an over-capacitive or poorly terminated bus.
Follow the manufacturer recommendations for bypassing and power-supply sequencing. Place the required input and ground bypass components close to the device, with very short return paths to the supply pins. When the device interfaces to a board with additional legacy drivers, verify that all outputs are disabled during reset and power transitions; an incorrectly sequenced enable signal can produce contention even when the static logic design is correct.
Do not substitute a grouped eight-bit transceiver solely because the package has the same number of pins. The SN74LS242M has four individually organized transceiver elements, and differences in output-enable grouping can change system behavior even if the land pattern appears compatible. Compare every signal name, enable polarity, logic inversion, supply range, output-current rating, and temperature grade in the manufacturer pin-description and electrical-characteristics tables.
تعمیل کی معلومات
The LCSC product listing identifies the SN74LS242M as RoHS. No automotive qualification, REACH, lead-free, halogen-free, or conflict-minerals statement was identified for the exact ordering code.