SN74LS467N - Octal 3-State Buffer | Texas Instruments
MPN: SN74LS467N ✓ Hoạt độngSN74LS467N Tóm tắt
A tri-state buffer is a digital logic component that presents a strong logic level when enabled and a high-impedance state when disabled. The high-impedance condition allows multiple devices to share a data bus without creating output conflicts. Within the broader semiconductor hierarchy, the SN74LS467N belongs to the logic IC family, where buffer and line-driver functions strengthen digital signals and provide controlled bus participation.
The SN74LS467N uses bipolar LS-series logic. Its 5 V nominal supply operation is compatible with conventional TTL signal environments, while the 18 ns propagation-delay figure provides defined timing for address, data, and control paths. The 24 mA maximum IOL specification is important when the output must sink current from a short bus or heavily loaded receiver. Because it is an eight-position device, one package can support multiple independently controlled bus segments when the application uses the appropriate enable structure.
Three-state outputs are most valuable when several physical devices connect to a common conductor. When all connected drivers are disabled simultaneously, the shared line can be released without permanently shorting it to a logic level. PCB design must still reserve adequate drive strength and termination for the intended bus topology. Long traces, capacitive loading, stubs, and simultaneous transitions can reduce practical timing margin even when the nominal propagation delay is suitable.
Typical uses include bus-interface buffering, digital signal isolation, address multiplexing, control-line routing, and industrial or legacy TTL systems. The 20-pin PDIP package also favors through-hole construction, repairable assemblies, prototyping, and equipment where leaded components are preferred over fine-pitch surface-mount packages. Its larger lead spacing also makes inspection and manual rework straightforward.
Designers should verify the enable truth table and signal states in the manufacturer datasheet before connecting unused sections. Keep disabled outputs electrically isolated from other drivers, maintain compatible logic thresholds throughout the bus, and account for the 18 ns delay in setup and hold timing. The 24 mA IOL limit should be checked against the worst-case load.
This product page combines the known electrical and package characteristics of the SN74LS467N with practical implementation guidance, source-backed purchasing information, and same-family replacement analysis for engineers evaluating legacy TTL bus-buffer designs.
Bộ thay thế dễ dàng lắp đặt cho SN74LS467N — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
SN74LS467
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
SN74LS467A
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
SN74LS467N Tỷ lệ tối đa & tính chất điện
| Device Type | Octal buffer with three-state outputs |
| Logic Family | LS-series bipolar TTL |
| Number of Output Elements | 8 elements |
| Kiểu đầu ra | 3-state, element per element |
| Nominal Supply Voltage | 5 V |
| Propagation Delay | 18 ns |
| Maximum Low-Level Output Current | 24 mA |
| Package Type | 20-pin PDIP |
| Số chân | 20 pins |
| Kiểu lắp đặt | Through-hole |
Hướng dẫn cấu hình chân SN74LS467N 20-pin pdip
Cấu hình chân cho SN74LS467N (20-pin pdip gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho SN74LS467N.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
SN74LS467N phù hợp cho 6 Áp dụngs: Legacy TTL Data Bus Buffering, Address Multiplexing, Control-Line Signal Isolation, Digital Test and Measurement Equipment, Industrial Control-System Backplanes, Legacy Processor Interface Buffering.
Legacy TTL Data Bus Buffering
The SN74LS467N fits a legacy 5 V TTL data bus where several buffered channels must connect to shared conductors. Its eight three-state output positions can be selectively enabled, while the 18 ns propagation delay provides a defined switching interval for conventional TTL timing. A 24 mA maximum low-level output current gives designers a clear sink-current ceiling when estimating worst-case bus loading. Keep enable decoding mutually exclusive so that no two enabled outputs drive the same line. Because this is a 20-pin through-hole device in a 5 V TTL environment, it is especially useful for maintaining existing through-hole control, test, or industrial equipment rather than introducing a mixed-voltage redesign.
Được đề xuất
Address Multiplexing
The SN74LS467N can support address or control multiplexing in a 5 V digital system that needs multiple buffered fields to share common conductors. Its octal structure provides eight three-state output positions, and each disabled position releases the bus so another source can take control. The 18 ns propagation-delay characteristic must be included in the multiplexer timing budget alongside enable decoding delay and receiver settling. Designers should use the device truth table to ensure that data and address fields do not overlap incorrectly during each select interval. The 20-pin PDIP format is particularly practical in legacy backplanes, laboratory equipment, and repair assemblies where leaded logic packages are standard.
Được đề xuất
Control-Line Signal Isolation
The SN74LS467N is useful when control signals from a 5 V TTL source need buffering before driving a shared digital interface. Its three-state outputs allow a section to become high impedance during another device's active interval, preventing contention on shared control conductors. The 18 ns propagation delay provides a timing value for sequencing enable and data signals, while the 24 mA maximum IOL rating defines the usable sink-current margin. A practical implementation should keep the disabled-output node free of pull-ups or pull-downs that would interfere with intentional high-impedance operation. Verify polarity and timing in the manufacturer truth table before assigning functions to the 20 pins.
Được đề xuất
Digital Test and Measurement Equipment
The SN74LS467N can serve as a bus-interface element in 5 V TTL test and measurement equipment that must route control or data signals among several circuit sections. Its eight three-state outputs support shared-bus architecture, and its 18 ns propagation delay is suitable for conventional instrument-control buses when the enable timing is included correctly. The 24 mA IOL limit should be compared with the worst-case receiver and termination load to avoid excessive sink current. The 20-pin PDIP package is advantageous for repairable laboratory equipment and through-hole prototyping because it provides generous lead spacing, straightforward inspection, and easier manual replacement than a fine-pitch surface-mount logic package.
Được đề xuất
Industrial Control-System Backplanes
The SN74LS467N is applicable to legacy industrial control backplanes that use 5 V TTL signaling and require grouped bus outputs with three-state control. The octal device allows several signal lines to share conductors when only one driver section is enabled at a time. Its stated 18 ns propagation delay should be checked against backplane length, receiver capacitance, and any additional transceiver delay, while the 24 mA maximum IOL rating limits direct load current. Long or capacitive backplanes may require series damping to control edge rates. The through-hole 20-pin PDIP package also remains practical for repair-oriented industrial equipment built with leaded logic components.
Được đề xuất
Legacy Processor Interface Buffering
The SN74LS467N can buffer legacy processor data or control lines where a shared 5 V TTL bus must support several possible drivers. The octal three-state architecture separates source signals from the shared conductors and permits unused outputs to remain inactive. Designers must incorporate the 18 ns propagation delay and the enable settling interval into processor setup and hold requirements. The 24 mA maximum low-level output current provides the primary current limit for receiver and termination analysis. Because the SN74LS467N is a 20-pin PDIP part, it is especially appropriate for maintaining an existing processor board without changing its footprint, provided the exact enable and data mapping matches the original circuit.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho SN74LS467N — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | SN74LS467 | SN74LS467A |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 20-pin PDIP | 20-pin PDIP | 20-pin PDIP |
| Function | Octal buffer with three-state outputs | Octal buffer with three-state outputs | Octal buffer with three-state outputs |
| Output Elements | 8 elements | 8 elements | 8 elements |
| Nominal Supply Voltage | 5 V | 5 V | 5 V |
| Mounting Type | Through-hole | Through-hole | Through-hole |
| Logic Family | LS-series bipolar TTL | LS-series bipolar TTL | LS-series bipolar TTL |
Bảo phân biệt quan trọng
- Element-level tri-state control supports shared-bus designs (vsSN74LS467)
- The original N ordering option is documented as a 20-pin PDIP device (vsSN74LS467A)
- Established through-hole construction supports legacy PCB compatibility (vsSN74LS467)
Ghi chú thiết kế
Do not enable two SN74LS467N output sections that drive the same conductor. Although the three-state outputs can be released, two simultaneously active drivers can create a direct logic conflict and excessive current. Build the enable decoder so that only one source owns each shared bus segment, and use the manufacturer truth table to verify active-high or active-low control behavior for every pin.
Include the stated 18 ns propagation delay, enable-transition delay, and receiver settling time when creating a timing budget. PCB capacitance and long traces can increase observed transition time beyond the nominal device figure. For long or lightly loaded lines, evaluate source termination rather than relying on the 24 mA IOL rating as a substitute for correct transmission-line design.
Maintain a common return path and place the device so shared-bus traces remain short and have controlled capacitive loading. The 20-pin PDIP package provides generous lead spacing, but pin-assignment mistakes remain easy without careful schematic review. Mark the orientation notch on the PCB, verify every enable and data signal, and inspect for solder bridges after hand soldering in legacy equipment.
Decouple the 5 V supply close to the device with the capacitance and placement prescribed by the manufacturer datasheet. Although the SN74LS467N is a logic IC rather than a power-conversion component, inadequate supply bypassing can add supply noise and reduce switching margin. Confirm that the 24 mA output-current rating is sufficient for the worst-case load while leaving margin for additional bus capacitance.
Thông tin tuân thủ
The device is a conventional logic IC rather than an automotive-qualified AEC-Q100 component. RoHS, REACH, lead-free, and halogen-free status require confirmation from the current manufacturer product documentation or lot documentation.