STM32F072R8T6 - 48MHz Cortex-M0 64KB MCU | STMicroelectronics
MPN: STM32F072R8T6 ✓ فعالSTM32F072R8T6 جائزہ
A microcontroller is a programmable semiconductor device that combines a processor core, memory, and peripherals on one integrated circuit. In the hierarchy of embedded semiconductors, the STM32F072R8T6 is a general-purpose MCU, while its ARM Cortex-M0 core provides deterministic 32-bit instruction execution for real-time control, communication, and human-interface applications.
Verified listing information identifies the device as a 48 MHz ARM Cortex-M0 MCU with 64 KB Flash, 16 KB SRAM, USB, CAN, and a 64-LQFP package. The STM32F0 family is suited to USB-enabled peripherals, CAN-connected equipment, industrial control modules, motor-control support, sensor nodes, and cost-constrained consumer products. Its 2 V to 3.6 V operating range, as reported by the verified search data, supports common embedded supply systems.
The STM32F072x8/xB device family combines high-performance processing with embedded peripherals and flexible memory options. The USB interface and CAN capability are important differentiators for designs that need device connectivity alongside general-purpose control. Exact peripheral counts, pin names, electrical limits, and timing values must be confirmed in the manufacturer datasheet before a production design is released.
Typical applications include USB-to-serial accessories, CAN gateway boards, motor-control and actuator electronics, industrial sensors, instrumentation, and low-power embedded controllers. Designers should preserve the recommended decoupling and routing practices, provide a stable clock and reset implementation, and verify all unused pins against the selected package pinout.
A key design consideration is that firmware compatibility is not guaranteed merely because another MCU has a similar peripheral set. Migration requires checking startup code, memory-map assumptions, interrupt priorities, clock trees, USB or CAN configuration, and package-level pin assignments. The STM32F072R8T6 is best selected when its verified 64 KB Flash, 48 MHz core, 16 KB SRAM, USB, and CAN combination matches the system requirements.
This page combines the verified manufacturer and distributor listing information with package-aware engineering context, application guidance, and replacement checks. Because the supplied search results do not include complete manufacturer electrical tables or a verified pin-by-pin mapping, unavailable values are explicitly marked rather than inferred.
کے لیے ڈراپ اِن متبادل STM32F072R8T6 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں STM32F072R8T6 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Core, Pin Count, Product Type, Flash Memory.
STM32F072R8T7
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →STM32F072RBT6
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →STM32F072RBT7
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →STM32F030RCT6
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →STM32F072R8T6 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Core | ARM Cortex-M0 32-bit RISC |
| Maximum CPU Frequency | 48 MHz |
| Flash Memory | 64 KB |
| SRAM | 16 KB |
| Operating Voltage Range | 2 V to 3.6 V |
| پیکیج | 64-LQFP, 10 x 10 mm |
| Architecture | 32-bit ARM Cortex-M0 |
| USB | Supported |
| CAN | Supported |
| Product Type | Microcontroller IC |
| ماؤنٹنگ ٹائپ | Surface Mount |
| Series | STM32F0 |
| Core Frequency | Up to 48 MHz |
| Flash Organization | 64K x 8 bits |
STM32F072R8T6 64-lqfp, 10 x 10 mm پن کنفیگریشن گائیڈ
STM32F072R8T6 (64-lqfp, 10 x 10 mm پیکیج) کے لیے پن کنفیگریشن۔ اس ڈیجیٹل IC میں GPIO، کمیونیکیشن انٹرفیس (UART، SPI، I2C) اور پاور پنز شامل ہیں۔ متبادل پن فنکشنز اور کنفیگریشن آپشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ ایمبیڈڈ سسٹم ڈیزائن اور PCB لے آؤٹ کے لیے ضروری۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں STM32F072R8T6.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
STM32F072R8T6 کے لیے موزوں ہے 7 ایپلیکیشنs: USB Peripheral Controller, CAN-Connected Industrial Sensor Node, USB-to-Serial Data Logger, Low-Power Embedded Control Module, Motor-Control and Actuator Interface, USB-CAN Protocol Gateway, Compact Instrumentation Front End.
USB Peripheral Controller
The STM32F072R8T6 is suitable for USB-enabled embedded accessories because the verified listing identifies USB support alongside a 48 MHz ARM Cortex-M0 core and 64 KB of Flash. A typical design places the MCU beside a USB transceiver and connector, then uses the MCU to enumerate the device, exchange data, and manage control functions. The 64 KB Flash limit should be checked against bootloader, application, and update requirements. Firmware architecture, USB clocking, decoupling, and connector protection are more important than simply matching the 64-LQFP package.
تجویز کردہ
CAN-Connected Industrial Sensor Node
The STM32F072R8T6 fits compact CAN-connected sensor nodes because the verified data identifies CAN support, a 48 MHz Cortex-M0 core, 16 KB SRAM, and a 2 V to 3.6 V supply range. The MCU can sample sensors, format measurements, and transmit them over a CAN transceiver to a larger controller. The design must account for transceiver standby behavior, bus termination, protection, common-mode requirements, and timing margins. Firmware should verify the exact peripheral pin assignments and interrupt behavior in the manufacturer documentation.
تجویز کردہ
USB-to-Serial Data Logger
The STM32F072R8T6 can act as the controller in a USB-to-serial data logger when its USB capability and 48 MHz processing rate are sufficient for the selected protocol and data rate. A practical design uses the MCU to receive sensor or host data, buffer it in the 16 KB SRAM, and forward it over USB. The available Flash must be budgeted for USB stack configuration, protocol handling, logging, and future updates. Test enumeration, suspend behavior, bus protection, and connector grounding on the assembled board.
تجویز کردہ
Low-Power Embedded Control Module
The STM32F072R8T6 is appropriate for compact embedded controllers that need general-purpose control, communication, and modest memory in a surface-mount package. Its 2 V to 3.6 V operating range permits integration with common low-voltage rails, while low-power modes can help reduce energy use when the final firmware and peripherals permit. Actual standby and wake-up behavior, current consumption, and clock-tree settings are not quantified in the supplied data and must be verified from the datasheet before making battery-life claims.
تجویز کردہ
Motor-Control and Actuator Interface
The STM32F072R8T6 can supervise actuator interfaces, motor-control logic, or small industrial equipment when its timers, GPIO, communication interfaces, and processing speed meet the system timing requirements. The 48 MHz Cortex-M0 core provides a responsive control platform, while USB and CAN can provide commissioning or network connectivity. Motor environments require isolation from switching noise, proper gate-driver placement, current sensing, protection, and thermal design. Verify the exact timer outputs and pin multiplexing before assigning a motor-control function.
تجویز کردہ
USB-CAN Protocol Gateway
The STM32F072R8T6 is a natural fit for a small protocol-conversion board that bridges USB to CAN. Its verified USB capability supports host or device connectivity, while CAN supports communication with industrial equipment. The firmware can translate frames, buffer messages, and expose configuration over USB. A production design still needs a USB transceiver, CAN transceiver, connector protection, accurate termination, common-mode handling, and a defined power budget. The 64 KB Flash and 16 KB SRAM should be checked against protocol stacks and logging features.
تجویز کردہ
Compact Instrumentation Front End
The STM32F072R8T6 can support compact instrumentation that combines sensor acquisition, local control, USB configuration, and optional CAN reporting. The 48 MHz core provides timing headroom for digital filtering and communication tasks, while the 16 KB SRAM can support short working buffers. Exact ADC characteristics were not included in the verified data, so analog measurement resolution, sampling behavior, reference requirements, and input ranges must be confirmed before selecting it for a precision measurement design.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا STM32F072R8T6 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | STM32F072R8T7 | STM32F072RBT6 | STM32F072RBT7 | STM32F030RCT6 |
|---|---|---|---|---|---|
| Package | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) | 64-LQFP (10x10 mm) |
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
اہم امتیازی خصوصیات
- USB and CAN connectivity in a 48 MHz Cortex-M0 MCU (بمقابلہSTM32F030RCT6)
- 64 KB Flash and 16 KB SRAM combination (بمقابلہSTM32F072R8T7)
- Documented 64-LQFP 10 x 10 mm package (بمقابلہSTM32F072RBT6)
ڈیزائن نوٹس
Design the supply for the verified 2 V to 3.6 V operating range and include local decoupling at every supply connection. USB, CAN transceivers, LEDs, sensors, and external memory should be included in the load budget, not treated as separate afterthoughts. Check startup ordering, regulator transient response, and the maximum current available during USB attachment. Exact capacitor values and current limits are not supplied here and must be taken from the manufacturer datasheet.
Place decoupling capacitors and any clock or reset components close to their associated STM32F072R8T6 pins, with short and continuous return paths. Keep USB and CAN traces away from noisy switching nodes and analog inputs, and follow the transceiver vendors' layout recommendations. The 64-LQFP footprint should be checked against the official package drawing before PCB release; the verified data confirms the 10 x 10 mm LQFP but does not provide a complete pin map.
Do not treat a same-family STM32 MPN as automatically drop-in compatible. Confirm pin names, alternate functions, Flash size, SRAM size, voltage limits, USB and CAN availability, clock configuration, startup behavior, and qualification markings. A replacement also requires checking bootloader and firmware dependencies. The supplied cross-reference snippets identify candidates but do not prove a complete equivalent, so engineering validation is required before production substitution.
تعمیل کی معلومات
The supplied verified data does not provide explicit compliance declarations for STM32F072R8T6. Check the current STMicroelectronics product documentation and distributor declarations before production release.